Closed tube sample introduction for gas chromatography-ion mobility spectrometry analysis of water contaminated with a chemical warfare agent surrogate compound

Ion mobility spectrometry (IMS) is a proven technology for detection of vapor phase chemical warfare agents. The technology is suitable for field portable instrumentation due to its small size, high sensitivity, speed of analysis, and low power consumption. However, it suffers from a limited dynamic range and potential difficulties in identifying compounds in complex matrices. The use of gas chromatography (GC) coupled to IMS can overcome the difficulty of chemical identification in mixtures by separating the sample into individual components before detection. Using this approach, IMS technology has previously been adapted to detect biological aerosols using an open tube pyrolyzer and a short GC column (Py-GC-IMS). The open sample introduction tube of a Py-GC-IMS instrument would be a convenient configuration to accept aerosol particulates, and while viewed as needed for aerosol trapping, is not optimal for liquid chemical analyses. To examine the usefulness of an existing Py-GC-IMS system for analysis of chemicals in water, an existing open-port sample interface was replaced with a septum-equipped closed tube injector to contain analyte vapors resulting from liquid injection. Tributylphosphate (TBP) was used as a surrogate chemical warfare agent, and aqueous injections into both closed and open tube assemblies were performed. Sample introduction into the closed tube inlet was also accomplished using solid phase microextraction (SPME) preconcentration. The limit of detection for TBP using an open tube, closed tube, and closed tube configuration with SPME sample introduction was 0.980, 0.196, and 0.0098 mg/L, respectively.     

Optimization of quartz tube pyrolysis atmospheric pressure ionization mass spectrometry for the generation of bacterial biomarkers

Experimental procedures were investigated to improve the efflux of biomolecule pyrolyzates from quartz tube pyrolysis under atmospheric pressure ionization mass spectrometry conditions. Heating regimes, airflows, and ion focusing parameters were optimized to increase the informative mass spectral signals generated from the pyrolysis of Gram-positive bacterial spores and vegetative cells. Dipicolinic acid (DPA) is found in 5-15% by weight in Gram-positive Bacillus spores, and the parameter optimization procedures provided an intense mass spectral signature of the m/z 168 protonated DPA molecule with a minimization of pyrolytic and ionization fragments. Moreover, mass spectral information from the optimization protocols yielded peaks and mass patterns characteristic of DNA and RNA nitrogen bases, protein diketopiperazines, and amino sugars.     

Switchable Q-switched and laser operating mode-locked erbium-doped fiber in the L-band region

We demonstrate a switchable Q-switched and mode-locked erbium-doped fiber laser （EDFL） operating in the L-band region using the nonlinear polarization rotation effect. The switching operation is achieved by controlling intensity-dependent loss using a polarization controller. In Q-switching mode, the EDFL produces a pulse train with a repetition rate of 21.1 kHz, pulse width of 7.7 #s, and pulse energy of 13.6 nJ. The EDFL also generates a multi-wavelength comb with a very narrow and constant wavelength spacing of 0.045 nm and optical signal-to-noise ratio of at least l0 dB. During mode locking, the EDFL produces stretched pulses with 3-dB bandwidth of 26.2 nm, pulse width of 350 fs, repetition rate of 2.38 MHz, and pulse energy of 48.56 pJ.     

Determination of total arsenic in soil and arsenic-resistant bacteria from selected ground water in Kandal Province, Cambodia

Cambodia has geological environments conducive to generation of high-arsenic groundwater and people are at high risk of chronic arsenic exposure. The aims of this study are to investigate the concentration of total arsenic and to isolate and identify arsenic-resistant bacteria from selected locations in Kandal Province, Cambodia. The INAA technique was used to measure the concentration of total arsenic in soils. The arsenic concentrations in soils were above permissible 5 mg/kg, ranging from 5.34 to 27.81 mg/kg. Bacteria resistant to arsenic from two arsenic-contaminated wells in Preak Russey were isolated by enrichment method in nutrient broth (NB). Colonies isolated from NB was then grown on minimal salt media (MSM) added with arsenic at increasing concentrations of 10, 20, 30, 50, 100 and 250 ppm. Two isolates that can tolerate 750 ppm of arsenic were identified as Enterobacter agglomerans and Acinetobacter lwoffii based on a series of biochemical, physiological and morphological analysis. Optimum growth of both isolates ranged from pH 6.6 to 7.0 and 30–35 °C. E. agglomerans and A. lwoffii were able to remove 66.4 and 64.1 % of arsenic, respectively at the initial concentration of 750 ppm, within 72 h of incubation. Using energy dispersive X-ray technique, the percentage of arsenic absorbed by E. agglomerans and A. lwoffii was 0.09 and 0.15 %, respectively. This study suggested that arsenic-resistant E. agglomerans and A. lwoffii removed arsenic from media due to their ability to absorb arsenic.     

Determination of neutron flux parameters in PUSPATI TRIGA Mark II Research Reactor, Malaysia

In standardization NAA, it is necessary to characterize the neutron spectrum parameters such as epithermal neutron flux shape factor (α), thermal to epithermal neutron flux ratio (f), thermal neutron flux (φ _th) and epithermal neutron flux (φ _epi) in the irradiation facility to determine the concentration of an element in the sample using absolute and k ₀ standardization methods. The α and f were determined using Cd-ratio multi monitor method using experimental data obtained in PUSPATI TRIGA Mark II research reactor at four irradiation positions (10, 20, 30 and 40) of the rotary rack. The calculated values of α and f ranged from 0.006 to 0.0281 and 18.56 to 19.12 respectively. The average values of φ _th and φ _epi were found as 2.33 × 10¹² and 1.23 × 10¹¹ n cm^?2 s^?1 respectively. Moreover, a comparison of the neutron flux parameters in the present study shows an acceptable level of consistency with those of previous studies.     

Investigate the capability of INAA absolute method to determine the concentrations of 238U and 232Th in rock samples

This work aimed to study the capability of INAA absolute method in determining the elemental concentration of ²³⁸U and ²³²Th in the rock samples. The INAA absolute method was implemented in PUSPATI TRIGA Mark II research reactor, Malaysian Nuclear Agency (NM). The accuracy of INAA absolute method was performed by analyzing the IAEA certified reference material (CRM) Soil-7. The analytical results showed the deviations between experimental and certified values were mostly less than 10 % with Z-score in most cases less than 1. In general, the results of analysed CRM Soil-7 show a good agreement between certified and experimental results which mean that the INAA absolute method can be used accurately for elemental analysis of uranium and thorium in various types of samples. The concentration of ²³⁸U and ²³²Th ranged from 1.77 to 24.25 and 0.88 to 95.50 ppm respectively. The highest value of ²³⁸U and ²³²Th was recorded for granite rock sample G17 of ²³⁸U and sample G9 of ²³²Th, whereas the lower value was 1.77 ppm of ²³⁸U recorded in sandstone rock and 0.88 ppm of ²³²Th for gabbro. Moreover, a comparison of the ²³⁸U and ²³²Th results obtained by the INAA absolute method shows an acceptable level of consistency with those obtained by the INAA relative method.     

Hybrid flat gain C-band optical amplifier with Zr-based erbium-doped fiber and semiconductor optical amplifier

An efficient gain-flattened C-band optical amplifier is demonstrated using a hybrid configuration with a Zirconia-based Erbium-doped fibre (Zr-EDF) and a semiconductor optical amplifier (SOA). The amplifier utilizes a two-stage structure with a midway isolator to improve flat gain characteristic and reduce noise figure. At input signal power of −30 dBm, a flat gain of 28 dB is obtained from wavelength region of 1530 to 1560 nm with gain variation of less than 4 dB. The noise figure is maintained below 11 dB at the flat-gain region. This amplifier has the potential to be used in the high channel count dense wavelength division multiplexing system due to its simplicity and compact design.     

Characterization and properties of low-linear-density polyethylene/Typha latifolia composites

The characterization of the effects of different sizes and loadings of Typha latifolia on the tensile, thermal, and morphological properties of linear-low-density polyethylene (LLDPE)/T. latifolia composites were evaluated using tensile test, Fourier transform infrared spectroscopy, thermogravimetric analysis, and scanning electron microscopy analyses. Results indicated the tensile strength and elongation at break decreased as T. latifolia loading increased. However, T. latifolia fine size (fs) exhibited better tensile properties than coarse size at the same loading in the composite. T. latifolia (15%, fs) recorded higher thermal stability than LLDPE control and other T. latifolia loadings and sizes due to the strong interaction of T. latifolia (15%, fs) in LLDPE matrix as shown in morphology.     

DFT investigation of NH3 physisorption on CuSO4 impregnated SiO2

In this quantum chemical investigation, NH(3) physisorption onto a model of copper sulfate impregnated silica is compared with pure silica and copper sulfate adsorbents. The physisorption process is modeled as direct binding of the NH(3) molecule to the adsorption site of the dry adsorbents and as displacement of a H(2)O molecule by NH(3) in the hydrated complexes. The surface of silica is represented by a hydroxyl group attached to a silsesquioxane cage, H(7)Si(8)O(12)(OH) and silica impregnated with CuSO(4) by the most stable configuration of the cluster containing a CuSO(4) ion pair placed adjacent to the silica cage. H(2)O is systematically added to the dehydrated adsorbents to investigate the role of water in NH(3) adsorption. Modeling hydrated environments of each type of adsorbent is focused on H(2)O molecules that directly coordinate with the active sites. The results indicate that the binding energy of adsorbing NH(3) onto the mixed adsorbent is greater than in pure silica. This enhanced binding in the mixed adsorbent is consistent with improved Br?nsted acidity of the silanol in the presence of CuSO(4).