Experimental analysis, modeling, and theoretical design of McMaster pore-filled nanofiltration membranes

A side-by-side comparison of the performance of McMaster pore-filled (MacPF) and commercial nanofiltration (NF) membranes is presented here. The single-salt and multi-component performance of these membranes is studied using experimental data and using a mathematical model. The pseudo two-dimensional model is based on the extended Nernst–Planck equation, a modified Poisson–Boltzmann equation, and hydrodynamic calculations. The model includes four structural properties of the membrane: pore radius, pure water permeability, surface charge density and the ratio of effective membrane thickness to water content. The analysis demonstrates that the rejection and transport mechanisms are the same in the commercial and MacPF membranes with different contributions from each type of mechanism (convection, diffusion and electromigration). Solute rejection in NF membranes is determined primarily by a combination of steric and electrostatic effects. The selectivity of MacPF membranes is primarily determined by electrostatic effects with a significantly smaller contribution of steric effects compared to commercial membranes. Hence, these membranes have the ability to reject ions while remaining highly permeable to low molecular weight organics. Additionally, a new theoretical membrane design approach is presented. This design procedure potentially offers the optimization of NF membrane performance by tailoring the membrane structure and operating variables to the specific process, simultaneously. The procedure is validated at the laboratory scale.     

Physical properties of glycosaminoglycan hydrogels

The chemical composition of glycosaminoglycan (GAG) hydrogels was found to have a profound effect on the physical properties of gels. Hyaluronan (HA) and chondroitin sulfate (CS) were each modified with adipic dihydrazide (ADH) with carbodiimide chemistry. The resulting polymer was crosslinked with various concentrations of poly(ethylene glycol) dialdehyde (PEG‐diald) to produce a series of hydrogels. The physical properties of these GAG hydrogels varied in a concentration‐dependent fashion. Maximal crosslinking was observed at a theoretical crosslinking of 50% for the HA‐ADH‐PEG‐diald hydrogels and 75% for the CS‐ADH‐PEG‐diald hydrogels. Adding PEG‐diald beyond the optimum for crosslinking prolonged the in vitro enzymatic degradation time of the hydrogels. The swelling of the crosslinked GAG hydrogels was correlated with the amount of PEG‐diald used rather than with the crosslinking density. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4344–4356, 2004     

Hyperfine magnetic fields at sp-sites in Co2YZ Heusler alloys

The systematics of hyperfine magnetic fields at sp impurities on the Z-sites in Co based Heusler alloys are investigated. New TDPAC measurements of Cd hyperfine fields are reported.     

Synthesis and characterization of a semiflexible liquid crystalline polyester with a broad nematic region

In this paper, we report on the synthesis and detailed characterization of a new semiflexible nematic liquid crystalline polyester which could serve as a 'model' polyester for a variety of physical and physico-chemical investigations. The polymer is a nematic liquid over a wide temperature range-from the glass transition temperature at ∼95°C to the isotropic transition at ∼240°C. We expect this polyester to be particularly useful for studying the effect of flow on the orientation of liquid crystalline polymers, as well as the production and removal of disclinations.     

Quantitative measurements of Ge surface segregation during SiGe alloy growth

Ge segregation during the growth of Si_{1 − x}Ge_x alloys (x = 5, 10, 20, and 40%) was studied using X-ray photoelectron spectroscopy. The alloys were grown in thicknesses up to 20.0 nm at 500°C to measure quantitatively the amount of segregated surface Ge. The length of alloy needed to reach steady-state growth edge was found to decrease with increasing alloy concentration (4.8, 2.8, 2.4, and 2.0 nm, respectively). It was found that each alloy had a complete monolayer of Ge on the surface and an increasing amount of segregated Ge in the second layer (20, 55, 80, and 95%, respectively) during steady-state growth. An increase in the temperature of alloy growth (400–750°C) resulted in an increase in the leading edge of alloy growth but did not change the amount of segregated Ge during steady-state growth. We propose that film stress is responsible for the amount of Ge segregation.     

Integration of microbolometers with infrared microstrip antennas

We report on various integration schemes of infrared microbolometers with microstrip antennas. The first integration design consists of two gold (Au) rectangular microstrip patches coupled along the radiating edges by a narrow niobium (Nb) strip. Devices using silicon oxide are compared to devices using amorphous silicon as antenna substrate. An extension of the twin-patch detector design is the microstrip dipole antenna-coupled microbolometer. Two ways of connecting the device to the contact pads via narrow dc leads are presented and compared. The contribution of the dc leads to the detector response is eliminated by directly connecting the dipole to the contact pads. The thermal isolation of the microbolometer from the silicon wafer is improved by incorporating air into the antenna dielectric substrate. This leads to higher detector responsivity and shifts the resonance towards longer antennas. The implementation of a bridge microstrip dipole antenna structure is also discussed.     

A short proof that N 3 is not a circle containment order

A partially ordered set P is called a circle containment order provided one can assign to each xP a circle C _x so that . We show that the infinite three-dimensional poset N ³ is not a circle containment order and note that it is still unknown whether or not [n]³ is such an order for arbitrarily large n.     

Production and characterisation of polyclonal antibodies to a derivative of 3-amino-2-oxazolidinone, a metabolite of the nitrofuran furazolidone

Polyclonal antibodies were produced to detect 3-amino-2-oxazolidinone (AOZ), a stable metabolite of the nitrofuran antibiotic furazolidone, following derivatisation with o-nitrobenzaldehyde. A carboxyphenyl derivative of AOZ was prepared, purified and conjugated to immunogenic carrier protein. Six antisera were produced from the immunisation of seven rabbits using various immunogen doses and time-scales. IC₅₀ values, as determined by competitive enzyme-linked immunosorbent assay (ELISA) suggested that reducing immunogen dose from 0.3 to 0.05 mg, while lengthening rest periods between booster immunisations from 2 to 8 weeks, increased the sensitivity of the antibodies to 3-{[(2-nitrophenyl)methylene]amino}-2-oxazolidinone (NPAOZ) from 3.8 to 0.3 μg l⁻¹. An IC₅₀ of 0.065 μg l⁻¹ (AOZ in the form of NPAOZ) was achieved with antiserum R670 by altering ELISA conditions. This antibody was highly specific for NPAOZ and did not cross-react with various nitrofuran metabolites, their nitrophenyl derivatives or a range of veterinary drugs. Antibody R670 is suitable for incorporation into an immunoassay for AOZ with sufficient sensitivity to satisfy current criteria for monitoring of veterinary drug residues. This is the first publication of an antibody for detection of a nitrofuran metabolite.