On the physical adsorption of gases on carbon materials from molecular simulation

In this paper we present a series of work covering a range of aspects relating molecular simulation to experiment. The importance of surface mediation type effects to the adsorption of simple and complex gases is demonstrated. Coupled with the adsorption of simple gases is their projection area when used for surface area determination. The pressure dependence of a projection area is demonstrated for argon at 77 and 87.3 K. A simple model is used to account for the degree of graphitisation of a surface is demonstrated and used to account for the isosteric heat behaviour of non-graphitised carbon blacks. Turning from surfaces to porous solids, an alternative treatment of experiment data (either sub or super critical) is presented that avoids the ambiguity of excess amounts adsorbed. Using this method one is able to obtain pore size distributions and amounts adsorbed without relying on such things as helium expansion volumes. Since this type of method is usually applied to composite solids we also demonstrate the correct method for calculating the heat of adsorption using independent sets of simulations. The final topic covered in this paper is an example of the information that can be gained from the heat capacity of an adsorbed phase.     

Crystal chemistry of the (Ta6Si4O26)6− and (Ta14Si4O47)8− frameworks

The range of chemical flexibilities of the hexagonal frameworks (Ta₆Si₄O₂₆)^6? and (Ta₁₄Si₄O₄₇)^8? have been partially explored. This has been done with high-temperature preparations as in general ionic mobilities in these frameworks are too low to permit low-temperature ion exchange. Ionic site potential calculations indicate that preferential site-occupancy factors as well as geometric constraints are responsible for the absence of ionic motion. New phases K_6?xNa_xTa₆Si₄O₂₆ (x ? 4), K_8?xNa_xTa₁₄Si₄O₄₇ (x ? 5), and impure Ba_3?xNa_2xTa₆Si₄O₂₆ have been prepared. Introduction of up to 2 moles of Li⁺ and 1 mole of Mg²⁺ ions per formula unit into sites of the framework not normally occupied has been demonstrated as well as the possibility of partially substituting Zr⁴⁺ for Ta⁵⁺ ions. Substitutions designed to introduce large tunnel vacancies in the presence of only monovalent K⁺ or Na⁺ ions (P for Si, W for Ta and F for O) generally proved unsuccessful. Competitive phases also frustrated attempts to substitute either the larger Rb⁺ or the smaller Li⁺ ions into the large-tunnel sites. A large area of solid solution was discovered in the BaONa₂OTa₂O₅ phase diagram; it has a (TaO₃)-framework with the structure of tetragonal potassium tungsten bronze.     

Scanning electron microscopy of foreleg tarsal sense organs of the poultry red mite, Dermanyssus gallinae (DeGeer) (Acari:Dermanyssidae)

Scanning electron microscopy (SEM) studies on the poultry red mite, Dermanyssus gallinae (DeGeer), showed that the tip of the foreleg tarsus of both sexes and early instar stages (larvae, protonymph and deutonymph) bears a cluster of 10 blunt peg-type sensillae. Diversity in size, shape and surface features of the wall of these sensillae characterize the sensilla complex (sensory field). Two short setae (1 and 2) with smooth walls lack detectable pores, whereas three medium-sized setae (4, 5 and 8) bear pores in the wall. Four medium or long setae (3, 6, 7 and 9) have longitudinal grooves or ribs in the wall, whilst one seta (10) possesses both pores and grooves in the wall. Based on the morphology, it is suggested that the porous setae could be olfactory receptors, and the grooved setae could be mechanoreceptors.     

The adsorption of water in finite carbon pores

Grand canonical Monte Carlo simulations were applied to the adsorption of SPCE model water in finite graphitic pores with different configurations of carbonyl functional groups on only one surface and several pore sizes. It was found that almost all finite pores studied exhibit capillary condensation behaviour preceded by adsorption around the functional groups. Desorption showed the reverse transitions from a filled to a near empty pore resulting in a clear hysteresis loop in all pores except for some of the configurations of the 1.0?nm pore. Carbonyl configurations had a strong effect on the filling pressure of all pores except, in some cases, in 1.0?nm pores. A decrease in carbonyl neighbour density would result in a higher filling pressure. The emptying pressure was negligibly affected by the configuration of functional groups. Both the filling and emptying pressures increased with increasing pore size but the effect on the emptying pressure was much less. At pressures lower than the pore filling pressure, the adsorption of water was shown to have an extremely strong dependence on the neighbour density with adsorption changing from Type IV to Type III to linear as the neighbour density decreased. The isosteric heat was also calculated for these configurations to reveal its strong dependence on the neighbour density. These results were compared with literature experimental results for water and carbon black and found to qualitatively agree.     

Comparative simulation study of nitrogen and ammonia adsorption on graphitized and nongraphitized carbon blacks

Grand canonical Monte Carlo simulation is used to study the adsorption of nitrogen at 77 K and ammonia at 240 K to represent weakly polar and polar molecules, respectively, on infinite and finite graphite surfaces. These graphite surfaces were modeled with different percentages of carbons removed (defects) from the top graphite layer. Increasing the number of defects increases the adsorption and the isosteric heat of nitrogen at low pressure. At moderate pressures the amount adsorbed is less due to the disruption in the packing of the nitrogen in the first layer. In contrast, the adsorption of ammonia at all pressures is reduced as the percentage of defects is increased. This is due to the disruption in ammonia bonding caused by the defects. The condensation-like step change in the ammonia isotherm on the perfect graphite surface is not observed for any of these surfaces with defects even for the case of only 10% defects. At high percentage of defects the adsorption isotherm is close to Henry law behavior for much of the pressure range. The adsorption on finite surfaces shows that the amount adsorbed for both molecules decreases compared with that of the infinite surfaces, resulting from interaction potentials with the surface and other fluid molecules at the edge. The decrease is much greater for the ammonia adsorption because the bonding between ammonia molecules is disrupted, meaning that the adsorption cannot follow the mechanism of condensation seen for the infinite surface.     

The drilling and cutting of polymethyl methacrylate (Perspex) by CO2 laser

Experiments were performed to determine the effect of lens, position and focal plane, speed of cut and power on the cutting and drilling rates of Perspex. The results were compared to the thermal conductivity and vapour removal theories developed and presented in the paper. The latter was found to be in good agreement with the experimental observations, and provides a sound basis for the assessment of laser machining of other materials which behave in a similar manner.     

Fast and efficient microwave-assisted synthesis of functionalized peptoids via Ugi reactions

A wide range of N-alkylglycines (peptoids) can be efficiently prepared via Ugi reactions using microwave irradiations. The results confirm the versatility and efficiency of the methodology for the preparation of functionalized peptoids. The products can be used in consecutive Ugi reactions to yield cyclic peptoids of potential biological interest.