Surfactant effect on electrochemical-induced synthesis of α-Ni(OH)2

Nickel hydroxide films were electrosynthesized in the presence of different diluted surfactant solutions by galvanostatic electroprecipitation. Lamellar α-Ni(OH)₂ films are obtained using cationic surfactant cetyltrimethylammonium bromide (CTAB), anionic surfactant sodium dodecyl sulfate (SDS), and also neutral surfactant Tween® 80. The films were structurally and morphologically characterized by X-ray diffraction, thermal gravimetric analysis, Fourier transform infrared spectroscopy, and scanning electron microscopy, and electrochemically by cyclic voltammetry and electrochemical quartz crystal microbalance (EQCM). The results evidenced that SDS remains intercalated between the lamellae of α-Ni(OH)₂. Albeit the presence of CTAB and Tween® 80, it was noticed in FTIR spectra that the surfactants did not intercalate. The morphology was affected by the presence of different surfactants. All studied surfactants displaced the oxidation potential (E _O) of Ni²⁺/Ni³⁺ process to less positive values. Also, the presence of surfactants improved the electrode charge efficiency and the charge response for the same number of moles of nickel ions deposited. The ratio of the charge and frequency change is 4.4 times bigger for films deposited with SDS when compared with pure α-Ni(OH)₂ films.     

Decoding interleaved Reed–Solomon codes beyond their joint error-correcting capability

A new probabilistic decoding algorithm for low-rate interleaved Reed–Solomon (IRS) codes is presented. This approach increases the error correcting capability of IRS codes compared to other known approaches (e.g. joint decoding) with high probability. It is a generalization of well-known decoding approaches and its complexity is quadratic with the length of the code. Asymptotic parameters of the new approach are calculated and simulation results are shown to illustrate its performance. Moreover, an upper bound on the failure probability is derived.     

Inverse colloidal crystal membranes for hydrophobic interaction membrane chromatography

A collaborative study on the robustness and portability of a capillary electrophoresis‐mass spectrometry method for peptide mapping was performed by an international team, consisting of 13 independent laboratories from academia and industry. All participants used the same batch of samples, reagents and coated capillaries to run their assays, whereas they utilized the capillary electrophoresis‐mass spectrometry equipment available in their laboratories. The equipment used varied in model, type and instrument manufacturer. Furthermore, different types of sheath‐flow capillary electrophoresis–mass spectrometry interfaces were used. Migration time, peak height and peak area of ten representative target peptides of trypsin‐digested bovine serum albumin were determined by every laboratory on two consecutive days. The data were critically evaluated to identify outliers and final values for means, repeatability (precision within a laboratory) and reproducibility (precision between laboratories) were established. For relative migration time the repeatability was between 0.05 and 0.18% RSD and the reproducibility between 0.14 and 1.3% RSD. For relative peak area repeatability and reproducibility values obtained were 3–12 and 9–29% RSD, respectively. These results demonstrate that capillary electrophoresis‐mass spectrometry is robust enough to allow a method transfer across multiple laboratories and should promote a more widespread use of peptide mapping and other capillary electrophoresis‐mass spectrometry applications in biopharmaceutical analysis and related fields.     

Thermal transformations up to 1200 °C of Al-pillared montmorillonite precursors prepared by different OH–Al polymers

Aluminum-pillared montmorillonites are useful materials for their application as catalysts, adsorbents and ceramic composites. The precursor is a pillared montmorillonite that is not thermally stabilized. The precursor preparation methods, textural properties and catalytic activity have been extensively investigated, but comparatively, studies concerning their thermal transformations at high temperature are limited. In this work, precursors were prepared using two types of montmorillonites, Cheto (Ch) and Wyoming (W), and using two different OH–Al polymer sources: hydrolyzed (H) and commercial (C) solutions. Structural and thermal transformations of the precursors with heating up to 1200 °C were determined by X-ray diffraction and thermogravimetric analysis. Thermal analysis of these precursors below 600 °C revealed the influence of OH–Al polymers from the two solutions. The major phases developed at 1200 °C from the original montmorillonites were mullite for W and cordierite for Ch. The content of these phases depended on the aluminum in the octahedral sheet of the pristine montmorillonites. Amorphous phase, cristobalite, spinel, sapphirine and others phases were also found. The intercalation of OH–Al polymers in montmorillonites caused an increase in amorphous content after treatment at 1030 °C; however, it favored mullite development above 1100 °C. Although total aluminum content of both W and Ch precursors was similar, the transformation to mullite was directly related to the octahedral aluminum/magnesium ratio. The phase composition of the products at 1200 °C was not dependent on the type of intercalated OH–Al polymers. The increase in mullite content of the thermally treated precursors contributes to its possible application as advanced ceramic products.     

Optimal transport and a bilevel location-allocation problem

In this paper a two-stage optimization model is studied to find the optimal location of new facilities and the optimal partition of the consumers (location-allocation problem). The social planner minimizes the social costs, i.e. the fixed costs plus the waiting time costs, taking into account that the citizens are partitioned in the region according to minimizing the capacity costs plus the distribution costs in the service regions. By using optimal transport tools, existence results of solutions to the location-allocation problem are presented together with some examples.     

PET Diagnostic Molecules Utilizing Multimeric Cyclic RGD Peptide Analogs for Imaging Integrin αvβ3 Receptors

Multimeric ligands consisting of multiple pharmacophores connected to a single backbone have been widely investigated for diagnostic and therapeutic applications. In this review, we summarize recent developments regarding multimeric radioligands targeting integrin α_vβ₃ receptors on cancer cells for molecular imaging and diagnostic applications using positron emission tomography (PET). Integrin α_vβ₃ receptors are glycoproteins expressed on the cell surface, which have a significant role in tumor angiogenesis. They act as receptors for several extracellular matrix proteins exposing the tripeptide sequence arginine-glycine-aspartic (RGD). Cyclic RDG peptidic ligands c(RGD) have been developed for integrin α_vβ₃ tumor-targeting positron emission tomography (PET) diagnosis. Several c(RGD) pharmacophores, connected with the linker and conjugated to a chelator or precursor for radiolabeling with different PET radionuclides (¹⁸F, ⁶⁴Cu, and ⁶⁸Ga), have resulted in multimeric ligands superior to c(RGD) monomers. The binding avidity, pharmacodynamic, and PET imaging properties of these multimeric c(RGD) radioligands, in relation to their structural characteristics are analyzed and discussed. Furthermore, specific examples from preclinical studies and clinical investigations are included.