Quantitative electron probe microanalysis for the characterization of thin carbon-boron layers in fusion devices

Summary The first wall of the fusion device TEXTOR at the Forschungszentrum Jülich has been coated in situ with an amorphous hydrogen rich carbon/boron film (a-C/B:H) which reduces plasma impurities caused by the plasma surface interaction. The results of the coating process of the 35 m² large inner wall surface have been controlled by a recently developed modification of the quantitative electron probe microanalysis, which has been applied to 12 samples from specified positions inside the tokamak. The quantification itself is based on a Monte Carlo simulation of electron trajectories providing very accurate results for X-ray intensities emitted by elements present in the electron bombarded sample. The Monte Carlo results are used in the present work to calibrate the measured X-ray intensities emitted by boron and carbon from the a-C/B:H layers deposited on pure silicon substrates. As a result the total deposited mass of the layer per area unit as well as the composition of the layers (except hydrogen) could be determined very accurately. The relative errors were less than 7%. The limit of detectability were found to be in the range of one monolayer for boron as well as for carbon.     

3,7-Dioxaazelaamides as Ionophores for Lithium Ion Selective Liquid Membrane Electrodes

Lipophilic neutral carriers were synthesized which show Li⁺/Na⁺ selectivities of up to ca. 80 in highly lipophilic liquid membranes. The sensor membranes exhibit improved response times and increased lifetimes as compared to systems described earlier. They allow reliable measurements of Li⁺ in blood serum within the clinical concentration range. A 1:1 Li⁺/ionophore complex of one representative (N,N,N′,N′-tetracyclohexyl-5,5-dimethyl-3,7-dioxaazelaamide) has been prepared, and its structure was elucidated by X-ray analysis.     

Cyclobut-2-enones from Alkynes via Dichlorocyclobut-2-enones

The [2 + 2]-cycloaddition of dichloroketene (prepared in situ from CCl₃COCl and Zn(Cu)) with three alkynes 1a–c to form 2,3-dimethyl-( 2a ), 2,3-diethyl-( 2b ) and 3-butyl-4,4-dichlorocyclobut-2-enone ( 2c ) proceeds rapidly in the absence of POCl₃. The primary products 2a–c rearrange in situ to the 2,4-dichlorocyclobut-2-enones 3a–c under the influence of ZnCL₂ produced during the reaction. ZnCl₂ converts both 2a and 3a into a 4:6 equilibrium mixture of the two; this isomerization does not occur with LiCl. The Cl-atoms of both 2a , b and 3a , b and of 2c may reductively be removed with Zn(Cu) in AcOH/pyridine to afford the alkylcyclobutenones 4a-c . Without pyridine, this reduction gives ca. 1:1 mixtures of the double-bond isomers 4 and 5 in low yields. The cyclobutenones 2c and 4c may be deuterated by CD₃COOD in the presence of pyridine. D -Atom is introduced into 2c at C(4) and at C(γ), and into 4c at C(2) and C(4). A mechanism for this deuteration is considered, which does not involve a cyclobutadienolate 7 , but rather a cyclobutenolate of type 8 . The reductions of 2 and 3 to 4 might also pass through the same type of intermediate 8 .     

N,N,N′,N′-Tetrabutyl-3,6-dioxaoctan-dithioamid,Ionophor mit Selektivität für Cd2+

N,N,N′,N′-Tetrabutyl-3,6-dioxaoctane-dithioamide, an Ionophore with Selectivity for Cd²⁺ The dioxa-dithioamide 3 behaves as a highly selective ionophore for Cd²⁺ in solvent polymeric membranes. It induces cation-permselectivity in these membranes with a transference number of 1 for Cd(NO₃)₂- and of 2 for CdCl₂-solutions. In the presence of a proton carrier, 3 may be used to selectively pump Cd²⁺ through membranes by coupling with a pH gradient.     

Determination of short-lived activation products in neutron-irradiated sodium through application of hydrated antimony pentoxide

A method for the determination of short-lived activation products in neutron-irradiated sodium is described. It is based on hydrolysis of sodium with methanol, separation of Na⁺ with specially prepared antimony pentoxide (HAP) possessing very high selectivity and capacity, and subsequent gamma-spectroscopic measurement of the activation products.     

Preparation of Neutral Ionophores for Alkali and Alkaline Earth Metal Cations and their application in ion selective membrane electrodes

The preparation of a series of non-cyclic, uncharged ligands able to selectively complex alkali and alkaline earth metal cations is described. These molecules are designed to be used as carriers for cations through membranes. Some of the compounds show high Ca²⁺ and Na⁺ selectivity, respectively, in liquid membrane electrodes.     

Lipophilic Diamides as Ionophores for Alkali and Alkaline Earth Metal Cations

A series of lipophilic N, N, N′,N′-tetrasubstituted diamides were prepared and their selectivity in solvent polymeric membranes was studied, cis-N, N, N′, N′-Tetraisobutylcyclohexane-1,2-dicarboxamide induces a selectivity in membranes for Li⁺over alkaline earth metal cations and other alkali metal cations by a factor of about 1000 and 100 respectively. The ionophore N, N′-diheptyl-N,N′-dimethylethylmalonamide is an attractive candidate for the use in microelectrodes for the determination of intracellular Mg²⁺-activities.     

Studies on the preparation of hydrated antimony pentoxide (HAP) to separate Na+ in the field of radioanalytical investigations

Summary Hydrated antimony pentoxide with favourable chemical and mechanical properties could be produced from an aqueous suspension of antimonic acid by a two stage drying process.A decisive factor for the pre-drying is that the compound should be given the chance to form crystalline structure, the existence of which is the primary condition for the retentive effect of HAP on Na⁺-ions.The post-drying leads to a decrease of elutability of Na⁺-ions. This is accompanied by a reduction of the lattice constant and the water content of the products.

---

Über die Herstellung von wasserhaltigem Antimonpentoxid zur Abtrennung von Na⁺ bei radioanalytischen Untersuchungen

Zusammenfassung Wasserhaltiges Antimonpentoxid mit ausgezeichneten chemischen und mechanischen Eigenschaften läßt sich durch einen zweistufigen Trocknungsprozeß aus einer wäßrigen Suspension von Antimon-V-säure herstellen. Entscheidend für die Vortrocknung ist, daß die Verbindung kristalline Struktur annimmt. Dies ist die erste Bedingung für den Retentionseffekt gegenüber Na-Ionen. Die Nachtrocknung führt zur Abnahme der Auswaschbarkeit dieser Ionen. Daneben erfolgt eine Herabsetzung der Gitterkonstante und des Wassergehaltes der Produkte.