Incorporation methods for cholic acid chitosan-g-mPEG self-assembly micellar system containing camptothecin

A water-insoluble anticancer agent, camptothecin (CPT) was incorporated to a polymeric micelle carrier system preparing from cholic acid chitosan-grafted poly (ethylene glycol) methyl ether (CS-mPEG-CA). CS-mPEG-CA formed a core–shell micellar structure with a critical micelle concentration (CMC) of 7.08 μg/ml. Incorporation efficiency was investigated by varying physical incorporation method and initial drug loading. Among three incorporation methods (dialysis, emulsion and evaporation methods), an emulsion method showed the highest CPT incorporation efficiency. Increasing the initial CPT loading from 5 to 40%, the incorporation efficiency decreased. In all examined CPT-loaded CS-mPEG-CA micelles, 5% initial drug loading showed the highest drug incorporation efficiency. Release of CPT from the micelles was sustained when increasing the initial CPT loading. This indicates the importance of incorporation method and the initial drug loading to obtain the optimum particle size with high drug loading and sustained drug release. When compared to the unprotected CPT, CPT-loaded CS-mPEG-CA micelles were able to prevent the hydrolysis of the lactone group of the drug. This novel CS-mPEG-CA polymer presents considerable potential interest in the further development of CPT carrier.     

Rheological and morphological characterizations on physical stability of gamma-oryzanol-loaded solid lipid nanoparticles (SLNs)

In the present study, gamma-oryzanol was incorporated into glycerol behenate (Compritol 888 ATO) nanoparticles (SLNs) at 5 and 10% (w/w) of lipid phase. Increasing lipid phase concentration resulted in increased consistency and particle diameter of SLNs. Upon storage over 60 days at 4, 25 and 40 °C, the instability was observed by rheological analysis for all samples due to the formation of gelation. Rheological measurement revealed the increase in storage modulus and critical stress during storage at all temperatures. However, at 40 °C, the pronounced instability was observed from the highest increase in storage modulus and a formation of rod-like network structure from scanning electron micrographs. An increase in crystallinity, determined by differential scanning calorimetry, was also found during storage at all temperatures, confirming the instability of SLNs. Particle diameters and zeta potentials of both concentrations at all storage conditions failed to explain the observed instability. These investigations may help to develop formulations of solid lipid nanoparticles, which are optimized with respect to the desired rheological properties.     

Formulation and stability of Moringa oleifera oil microemulsion

Moringa oleifera oil with comparable caprylic triglyceride to Lexol® 865 and higher oleic acid was prepared into microemulsions. A system comprising natural and synthetic oils (O_mix), surfactant (Tween 80 and Span 80; S_mix), and water was microemulsion prepared by a visual grading. Twelve microemulsions with diameter of 83.75–286.76 nm, pH of 6.75–8.23, and viscosity of 280.00–517.20 mPa?s were produced. Their antioxidant were 0.926–2.921 μg Trolox/mg. Microemulsions with O_mix:S_mix mass ratio of 2:8 and 5:5 that had O_mix of 2:1 and 1:1 were stable following a 4 months stability evaluation at 25°C and 45ºC. Microemulsions containing moringa oil produced by a practical low-energy method exhibited good viscosity with an acceptable pH and antioxidant activity were therefore applicable for further applications.     

Gelatin scaffolds functionalized by silver nanoparticle‐containing calcium alginate beads for wound care applications

The embedding of silver nanoparticle (nAg)‐containing calcium alginate (CaAlg) beads in gelatin scaffolds was aimed to reduce the burst release and prolong the release of silver (Ag⁺) ions for a long period of time. The reduced sizes of the nAg‐containing CaAlg beads were prepared by an emulsification/external gelation method. The diameter of these beads was ~2 µm. The nAg‐containing CaAlg beads were then embedded into gelatin scaffolds by a freeze‐drying method for evaluating the potential of these scaffolds as wound dressings. The compressive modulus of these scaffolds embedded with nAg‐containing CaAlg beads ranged between 7 and 9 kPa. For release study, the cumulative released amounts of Ag⁺ ions from the nAg‐containing CaAlg beads embedded in gelatin scaffolds were lower than those from the nAg‐containing CaAlg beads. Moreover, the nAg‐containing CaAlg beads embedded in gelatin scaffolds had great antibacterial activity and low cytotoxicity. Thus, these scaffolds had potential for sustaining the release and use in wound care applications, especially chronic wound. Copyright © 2016 John Wiley & Sons, Ltd.     

Preparation of PMMA/acid-modified chitosan core-shell nanoparticles and their potential as gene carriers

The core-shell nanoparticles consisting of poly(methyl methacrylate) (PMMA) cores surrounded by various acid-modified chitosan shells were synthesized using a surfactant-free emulsion copolymerization, induced by a tert-butylhydroperoxide (TBHP) solution. Methyl methacrylate (MMA) was grafted onto four acid-modified chitosans (hydrochloric, lactic, aspartic, and glutamic acids) with MMA conversions up to 64%. The prepared nanoparticles had diameter ranging from 100 to 300 nm characterized by atomic force microscopy and displayed highly positive surface charges up to +77 mV. Transmission electron microscopic images clearly revealed well-defined core-shell morphology of the nanoparticles where PMMA cores were coated with acid-modified chitosan shells. The effect of acid-modified chitosans on particle size, intensity of surface charge, morphology, and thermal stability were determined systematically. The plasmid DNA/nanoparticles complexes were investigated with ζ-potential measurement. The results suggested that these nanoparticles can effectively complex with plasmid DNAs via electrostatic interaction and could be used as gene carriers.