Formation of porous polymer morphology by microsyneresis during divinylbenzene polymerization

This article describes the investigation of the importance of various reaction conditions on microsyneretic pore formation during polymerization of divinylbenzene (DVB) under so‐called “solvothermal” conditions. To induce microsyneretic pore formation, the most important parameter is an unusually high dilution of monomers with a “good” porogen solvating the polymer chains. High dilution and solvation of the growing poly(DVB) chains promote the prolongation of the polymer chains rather than their interconnection by crosslinking. Consequently, when the polymer gel density reaches the point where syneresis starts, the polymer network is geometrically too extensive to be broken up into precipitating entities and, instead, porogen droplets are formed within the continuous polymer gel. The pore geometry created by microsyneresis offers high surface area in wide mesopores and hence, high capacity for supporting functional groups or reactions with much better accessibility than narrow pores between polymer microspheres produced by macrosyneresis in conventional styrenic polymer supports. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 774–781     

Mechanical properties of metallic ribbons investigated by depth sensing indentation technique

The paper presents mechanical properties of two kinds of Co-based and one Fe-based metallic ribbons by the depth sensing indentation (DSI) technique. Investigations were carried out on two kinds ternary alloy Co₇₇Si_11,5B_11,5 and Fe₇₈Si₁₃B₉ and multicomponent Co₆₈Fe₄Mo₁Si_13,5B_13,5, which are so-called “zero-magnetostriction” materials. Metallic ribbons were investigated in amorphous state and partially crystallized state after annealing in 400°C in argon atmosphere. Heating of ribbons obtained by melt spinning technique was performed to check its effect on changes of mechanical properties.     

Synthesis and evaluation of a C8 stationary phase on a silica hydride surface by hydrosilation of 1-octyne

The silanization/hydrosilation method is used to bond an alkyne (1-octyne) to a silica hydride surface. The new bonded material is characterized by elemental analysis and diffuse reflectance infrared Fourier transform spectroscopy. The hydrophobic behavior of this material was determined by the retention characteristics of aromatic solutes and the shape selectivity as well as phase classification (monomeric or polymeric) was measured by the polycyclic aromatic hydrocarbon mixture standard reference material 869. The presence of residual silanols on the bonded phase was probed by several basic solutes at pH 7. Long-term stability studies were conducted by measuring retention and peak symmetry of basic compounds over several thousand column volumes at pH 10.     

Mesoporous electrode material from alumina-stabilized anatase TiO2 for lithium ion batteries

A mesoporous electrode material whose structure is composed of anatase nanocrystals stabilized by alumina is reported. Powder X-ray diffraction shows the anatase phase only, but micro-Raman spectroscopy shows that the materials have a core-shell morphology with grains of bulk anatase covered by a thin rutile layer on the surface. This structure is unique when compared to analogous materials stabilized by zirconia (PNNL-1). Nitrogen adsorption isotherms demonstrate a monotonous increase in surface area and mesopore volume with increasing Al content. Thin film electrodes from these materials were characterized by lithium insertion electrochemistry. Cyclic voltammograms exhibit significant differences in Li accommodation in Al-free and Al-stabilized materials.     

Fullerenes separation with monomeric type C30 stationary phase in high-performance liquid chromatography

The temperature effect on the separation of fullerenes in LC was examined using monomeric type C30, C18 and C8 alkyl bonded stationary phases. It appears that the C30 phase exhibits superior separation ability for fullerenes. It is observed that the maximum retention temperature of fullerenes on the C30 phase is around 20 degrees C. A strong correlation between the changes in NMR spectra and the retention behavior of the solutes was found. The interpretation of the retention behavior of fullerenes on the alkyl bonded stationary phases, including the behavior in subambient temperature, is discussed using the information obtained by CP-MAS solid-state NMR spectroscopy and LC.     

Electrochemical doping of chirality-resolved carbon nanotubes

Raman spectra of electrochemically charged single-wall carbon nanotubes (HiPco) were studied by five different laser photon energies between 1.56 and 1.92 eV. The bands of radial breathing modes (RBM) were assigned to defined chiralities by using the experimental Kataura plot. The particular (n,m) tubes exhibit different sensitivity to electrochemical doping, monitored as the attenuation of the RBM intensities. Tubes which are in good resonance with the exciting laser exhibit strong doping-induced drop of the RBM intensity. On the other hand, tubes whose optical transition energy is larger than the energy of an exciting photon show only small changes of their RBM intensities upon doping. This rule presents a tool for analysis of mixtures of single-walled carbon tubes of unknown chiralities. It also asks for a re-interpretation of some earlier results which were reported on the diameter-selectivity of doping. The radial breathing mode in strongly n- or p-doped nanotubes exhibited a blue-shift. A suggested interpretation follows from the charging-induced structural changes of SWCNTs bundles, which also includes a partial de-bundling of tube ropes.     

Cyanato-copper(II) complexes with organic ligands,Part XXIII. Properties and structure characterization of cyanato-copper(II) complexes with aminopyridines

Summary New cyanato-copper(II) complexes with aminopyridines (ampy) were prepared and studied;viz. Cu(NCO)₂(3-ampy)₂ (- and -form), Cu(NCO)₂(3-ampy)₂(H₂O), Cu(NCO)₂(4ampy)₂, and Cu(NCO)₂(2-ampy). According to physical results, the Cu(NCO)₂L₂ complexes exhibitpseudo-octahedral structures with amine nitrogens or cyanate oxygens occupying axial sites. For - and -Cu(NCO)₂(3-ampy)₂ the crystal structure reorganization is connected with a change in axial distortion. The compound Cu(NCO)₂(2-ampy) is square pyramidal or — more probably — rhombic octahedral and its strong antiferromagnetism reveals the N-bridging function of the NCO groups.Part XXII, Ref. 9.