Pfaffian systems and Radon transforms on affine Grassmann manifolds

Mathematische Annalen -     

Determination of aqueous plutonium oxidation states by solvent extraction

The reliability of two solvent extraction techniques for the determination of Pu oxidation states in solution was tested with low-ionic-strength solutions and with high-Na and high-Mg brines that contained Pu concentrations sufficient for spectrophotometric analysis. One procedure only differentiates between reduced Pu [Pu(III) and Pu(IV)] and oxidized Pu [Pu(V) and Pu(VI)], whereas the second procedure was designed to differentiate between Pu(IV), Pu(V), and Pu(VI) in solution. Both procedures successfully differentiated between oxidized and reduced Pu in both dilute solutions and brines when tested with samples that contained only the Pu(IV), Pu(V), or Pu(VI) oxidation states. However, when the second solvent extraction procedure, which differentiates between Pu(V) and Pu(VI), was employed for solutions that did not contain a strong oxidant to maintain the Pu(VI) oxidation state, significant quantities of Pu(VI) were reduced to Pu(V) during extraction, indicating that accurate quantification of Pu(V) and Pu(VI) is not possible with this procedure.Work supported by the U. S. Department of Energy under Contract DE-ACO6-76RLO 1830.     

Flow-through particles for the high-performance liquid chromatographic separation of biomolecules: perfusion chromatography

This paper reports a new technique for reducing resistance to stagnant mobile phase mass transfer without sacrificing high adsorbent capacity or necessitating extremely high pressure operation. The technique involves the flow of liquid through a porous chromatographic particle, and has thus been termed "perfusion chromatography". This is accomplished with 6000-8000 A pores which transect the particle. Data from electron microscopy, column efficiency, frontal analysis and theoretical modelling all suggest that mobile phase will flow through these large pores. In this manner, solutes enter the interior of the particles through a combination of convective and diffusional transport, with convection dominating for Peclet numbers greater than one. The implications of flow through particles on bandspreading, resolution and dynamic loading capacity are examined. It is shown that the rate of solute transport is strongly coupled to mobile phase velocity such that bandspreading, resolution of proteins and dynamic loading capacity are unaffected by increases in mobile phase velocity up to several thousand centimeters per hour. The surface area of this very large-pore diameter material is enhanced by using a network of smaller, 500-1500 A interconnecting pores between the throughpores. Scanning electron micrographs show that the pore network is continuous and that no point in the matrix is more than 5000-10,000 A from a through-pore. As a consequence, diffusional path lengths are minimized and the large porous particles take on the transport characteristics of much smaller particles but with a fraction of the pressure drop. Capacity and resolution studies show that these materials bind and separate an amount of protein equivalent to that of conventional high-performance liquid chromatography as well as low performance agarose-based media at greater than 10-100 times higher mobile phase velocity with no loss in resolution.     

Use of the64Ni(36S,34,35Si)66,65Zn reactions to measure the masses of34Si and35Si

The ground-state masses of³⁵Si and³⁴Si have been measured using the reactions⁶⁴Ni(³⁶S,^35,34Si)^65,66Zn at a³⁶S beam energy of 198 MeV.^34,35Si¹⁴⁺ ions were analysed and identified in a QMG/2 magnetic spectrometer and gas-filled focal-plane detector. The experimental mass excess of³⁵Si was determined to be ?14.58± _0.12 ^0.07 MeV while that of³⁴Si was measured as ?19.961±0.034 MeV. A comparison is made with the results of mass model predictions.     

An efficient synthesis of cyclodextrin-based carbohydrate cluster compounds

[formula: see text] The photoaddition of the thiol 2,3,4,6-tetra-O-acetyl-beta-D-1-thioglucopyranose to the allyl ether functions of per-2-allyl-, per-6-allyl-, and per-2,6-diallyl-beta-cyclodextrin derivatives provides a remarkably simple and efficient way for attaching glucopyranose units onto (1) the secondary face, as well as (2) the primary face, of beta-cyclodextrin--not to mention (3) both the primary and secondary faces, simultaneously--in yields of up to 70%.