Physico-chemical characterization of nanofiltration membranes.

This study presents a methodology for an in-depth characterization of six representative commercial nanofiltration membranes. Laboratory-made polyethersulfone membranes are included for reference. Besides the physical characterization [molecular weight cut-off (MWCO), surface charge, roughness and hydrophobicity], the membranes are also studied for their chemical composition [attenuated total reflectance Fourier spectroscopy (ATR-FTIR) and X-ray photoelectron spectroscopy (XPS)] and porosity [positron annihilation spectroscopy (PAS)]. The chemical characterization indicates that all membranes are composed of at least two different layers. The presence of an additional third layer is proved and studied for membranes with a polyamide top layer. PAS experiments, in combination with FIB (focused ion beam) images, show that these membranes also have a thinner and a less porous skin layer (upper part of the top layer). In the skin layer, two different pore sizes are observed for all commercial membranes: a pore size of 1.25-1.55 angstroms as well as a pore size of 3.20-3.95 angstroms (both depending on the membrane type). Thus, the pore size distribution in nanofiltration membranes is bimodal, in contrast to the generally accepted log-normal distribution. Although the pore sizes are rather similar for all commercial membranes, their pore volume fraction and hence their porosity differ significantly.     

Some aspects of the interactions of orthopositronium with perfect and defect surfaces of insulating materials

ETLA (Elastic Thermalisation Lifetime Analysis) is a new model function for the fitting of lifetime spectra of slowly thermalising orthopositronium in the free space between the grains of insulating oxide powders. From this model one can obtain three fundamental parameters; the mass of the cluster of atoms which scatters the o-Ps, the probability that the o-Ps is forced into two-quantum decay at each collision and the emission energyE(0) of the o-Ps from the powder surface. As a consequence of full thermalisation of the Ps it is shown that the o-Ps quenching constant _q () follows atT ^1/2 dependency for MgO, Al₂O₃ and SiO₂ and for temperatures between 77 and 500 K. In MgO powder at low temperatures the irradiation by the positrons induces surface paramagnetic defects which are identified as Mg⁺ sites. These surface defects do not affect the thermalisation, but they induce paramagnetic o-p conversion i.e., an increase in , and they are also responsible for an increase in the emission energyE(0) of the o-Ps.     

First observation of the doubly charmed baryon Xi(+)(cc)

We observe a signal for the doubly charmed baryon Xi(+)(cc) in the charged decay mode Xi(+)(cc)-->Lambda(+)(c)K-pi(+) in data from SELEX, the charm hadroproduction experiment at Fermilab. We observe an excess of 15.9 events over an expected background of 6.1+/-0.5 events, a statistical significance of 6.3sigma. The observed mass of this state is 3519+/-1 MeV/c(2). The Gaussian mass width of this state is 3 MeV/c(2), consistent with resolution; its lifetime is less than 33 fs at 90% confidence.     

Lineshape factors and counting rate in annihilation radiation

Annihilation lineshape factor measurements are found to be influenced by the total counting rate observed by the Ge(Li) detector, and by the output pulse width of the main (semi-Gauss) amplifier. Counting rates have to be kept very low, typically below 2kHz.     

Microstructure and Defect Characterization of Nanostructured Ni3Al

 Nanostructured Ni₃Al was produced by the inert gas condensation and in situ compaction technique and characterized by means of high-resolution transmission electron microscopy (HRTEM), X-ray diffraction, and density measurements. The defect structure was investigated using positron annihilation lifetime spectroscopy (PALS). It is shown that in some samples besides the cubic also the martensitic phase can be present. The defect structure can be divided into three major components: vacancy-like defects in the grain boundaries and nano-voids with a size of 1 nm as seen with PALS, and large pores with sizes up to 8 nm as seen with HRTEM. Furthermore, it is shown that an increasing compaction temperature leads to significantly smaller nano-voids.     

ILEEMS: Methodology and Applications to Iron Oxides

ILEEMS is the acronym for Integral Low-energy Electron Mössbauer Spectroscopy. In this variant of Mössbauer spectroscopy the low-energy electrons, E < ～15 eV, emitted by the probe nuclei in the absorber are counted as a function of source velocity. As a consequence of their low energy, the detected electrons' origin lies within a very thin surface layer with thickness of a few nanometers and consequently, ILEEMS is a useful technique to examine surfaces of Fe-containing substances. In a first part of this paper the authors briefly describe the design of a home-made ILEEMS equipment allowing the temperature of the investigated sample to be varied between 77 K and room temperature. The second part of this contribution deals with a selection of results obtained from ILEEMS spectra for various Fe oxides. In particular, the following items are covered: (1) surface versus bulk Morin transition in small-particle and near-bulk hematite, α-Fe₂O₃; (2) bulk and thin-film magnetite, Fe₃O₄; (3) ferrihydrite, 5Fe₂O₃·9H₂0, goethite, α-FeOOH, and lepidocrocite, γ-FeOOH, all to some extent in relation to their morphology. Interesting and intriguing findings concerning the surface properties of these oxides were obtained and it is argued that the results encourage more systematic research in this and related fields using the surface-sensitive ILEEMS technique.