In-Situ Intrinsic Interface Strength Measurement at Elevated Temperatures and its Relationship to Interfacial Structure

A previously developed laser spallation technique has been modified to measure the tensile strength of thin film interfaces in-situ at temperatures up to 1100°C. Tensile strengths of Nb/A-plane sapphire, FeCrAl/A-plane sapphire and FeCrAlY/A-plane sapphire were measured up to 950°C. The measured strengths at high temperatures were substantially lower compared with their corresponding strengths at ambient temperature. For example, at 850°C, the interface tensile strength for the Nb/sapphire (151 ± 17 MPa), FeCrAl/sapphire (62 ± 8 MPa) and FeCrAlY/sapphire (82 ± 11 MPa) interface systems were lower by factors of approximately, 3, 5, and 8, respectively, over their corresponding ambient values. These results underscore the importance of using such in-situ measured values under operating conditions as the failure criterion in any life prediction or reliability models of such coated systems where local interface temperature excursions are expected. The results on alloy film interfaces also demonstrate that the presence of Y increases the strength of FeCrAl/Al₂O₃ interfaces.     

A high‐resolution scheme for low Mach number flows

A method for computing low Mach number flows using high‐resolution interpolation and difference formulas, within the framework of the Marker and Cell (MAC) scheme, is presented. This increases the range of wavenumbers that are properly resolved on a given grid so that a sufficiently accurate solution can be obtained without extensive grid refinement. Results using this scheme are presented for three problems. The first is the two‐dimensional Taylor–Green flow which has a closed form solution. The second is the evolution of perturbations to constant‐density, plane channel flow for which linear stability solutions are known. The third is the oscillatory instability of a variable density plane jet. In this case, unless the sharp density gradients are resolved, the calculations would breakdown. Under‐resolved calculations gave solutions containing vortices which grew in place rather than being convected out. With the present scheme, regular oscillations of this instability were obtained and vortices were convected out regularly. Stable computations were possible over a wider range of sensitive parameters such as density ratio and co‐flow velocity ratio. Copyright © 2004 John Wiley Sons, Ltd.     

Working group report: Quantum chromodynamics

This is the report of the subgroup QCD of Working Group-4 at WHEPP-9. We present the activities that had taken place in the subgroup and report some of the partial results arrived at following the discussion at the working group meetings.     

Quark mass corrections to the perturbative thrust and its effect on the determination of αs

We consider the effects of quark masses to the perturbative thrust in e ⁺ e ⁻ annihilation. In particular we show that perturbative power corrections resulting from non-zero quark masses considerably alters the size of the non-perturbative power corrections and consequently, significantly changes the fitted value of α_s.     

Change point estimation in non-monotonic aging models

The problem of estimating change points in various non-monotonic aging models is considered. A general methodology for consistent estimation of the change point is developed and applied to non-monotonic aging models based on the hazard rate function as well as on the mean residual life function.     

Use of Adogen-464 in some parent — daughter separations by reverse phase extraction chromatography

Seperation of few carrier-free daughter isotopes from their respective parents, e.g.,¹³²I from¹³²Te,¹⁴⁰La from¹⁴⁰Ba and²³⁴Th from²³⁸U, using Adogen-464, a high molecular weight quaternary ammoaium salt by reversed phase extraction chromatographic technique is reported.     

燃煤循环流化床燃烧脱硫的模型预测

燃煤循环流化床燃烧脱硫的模型预测池涌，岑可法，倪明江Ｐ·Ｂａｓｕ（浙江大学能源系杭州３１００２７）关键词：循环流化床，燃烧，脱硫，模型预测一、引言循环流化床锅炉在过去十几年中得到了广泛的应用，但与此同时由于循环流化床内流体动力特性的高度复杂使得数学模...     

Working group report: Neutrino and astroparticle physics

This is the report of neutrino and astroparticle physics working group at WHEPP-7. Discussions and work on CP violation in long baseline neutrino experiments, ultra high energy neutrinos, supernova neutrinos and water Cerenkov detectors are discussed.     

Synergistic effect of neutral donors on the extraction of zirconium(IV) by salicylaldoxime in dichloromethane

Liquid-liquid extraction of zirconium(IV) was investigated from dilute hydrochloric acid medium by salicyaldoxime (HA) in dichloromethane. The metal was spiked with ⁹⁵Zr and analyzed by its radioactivity. The effects of different donors, like trioctyl phosphine oxide (TOPO), triphenyl phosphine oxide (TPPO), tributyl phosphine oxide (TBPO), tributyl phosphate (TBP), trioctyl amine (TOA) and Amberlite LA-2 were studied. The adduct formation constants for both binary species (metal-ligand) and ternary species (metal-ligand-donor) were also calculated form the distribution data.One of the authors (S.B.) thanks The University of Burdwan for providing senior research fellowship to her. She also wishes to thank Dr. D. Mukherjee and Dr. S. Bhattacharya, B.U. for their valuable suggestions.     

Degradation process in organic thin film devices fabricated using P3HT

The stability of regioregular poly(3-hexylthiophene 2,5-diyl) (P3HT) thin films sandwiched between indium tin oxide (ITO) and aluminium (Al) electrodes have been investigated under normal environmental conditions (25°C and RH∼45–50%). Electrical and optical properties of ITO/P3HT/Al devices have been studied over a period of 30 days. Mobility μ of the order of 10⁻⁴ cm²/V-s has been obtained from the V ² law in the as-deposited P3HT films. Scanning electron microscopy (SEM) investigations show blistering of Al contacts in devices with a poly(3,4-ethylenedioxythiophene) (PEDOT) interlayer on application of voltage whereas no blistering is seen in devices without PEDOT. The results have been explained in terms of trap generation and propagation and the moisture-absorbing nature of PEDOT.