Optic Fiber Interferometer for Absolute Distance Measurement

1.IntroductionAbsolutedistancemeasurementisfarfromanewtopic.However,itisstillafieldstimulatinggreatinterestsnowadaysduetoitSimportantroleinmanufacturingandassembly['J.SincethegreatsuccessachievedbyMichelsonandBenoitwhentheyfirstdevelopedaninterferometertodeterminethestandardmeterintermsofthemonochromaticredcadmiumline,theopticinterferometerhasbeenprovedtobeoneofthemostpreciseandefficientwayindisplacementmeasurementbecauseofitshighdiscriminationandsimplestructure.However,thetraditionalinterfe…     

离心力场作用下多孔介质中强制对流换热的研究

对离心流化床中空气通过多孔物料层的强制对流换热进行了理论和实验研究。获得了气流和物料间强制对流换热的准则关联式。研究结果表明,在气流速度和温度梯度方向一致的条件下,强制对流换热比通常的边界层强制对流换热有所强化,其换热的准则关联式具有 Nu=CRePr的线性形式。从而验证了改变气流方向和热流密度矢量之间夹角可以强化换热的这一强化传热新原理。     

Calibrating software reliability models when the test environment does not match the user environment

Software failures have become the major factor that brings the system down or causes a degradation in the quality of service. For many applications, estimating the software failure rate from a user's perspective helps the development team evaluate the reliability of the software and determine the release time properly. Traditionally, software reliability growth models are applied to system test data with the hope of estimating the software failure rate in the field. Given the aggressive nature by which the software is exercised during system test, as well as unavoidable differences between the test environment and the field environment, the resulting estimate of the failure rate will not typically reflect the user‐perceived failure rate in the field. The goal of this work is to quantify the mismatch between the system test environment and the field environment. A calibration factor is proposed to map the failure rate estimated from the system test data to the failure rate that will be observed in the field. Non‐homogeneous Poisson process models are utilized to estimate the software failure rate in both the system test phase and the field. For projects that have only system test data, use of the calibration factor provides an estimate of the field failure rate that would otherwise be unavailable. For projects that have both system test data and previous field data, the calibration factor can be explicitly evaluated and used to estimate the field failure rate of future releases as their system test data becomes available. Copyright © 2002 John Wiley & Sons, Ltd.     

掺钕聚甲基丙烯酸甲酯的光学特性

研究了制备的掺钕螯合物Nd(DBM)3Phen材料的吸收光谱、激发光谱、荧光光谱,应用Judd-Ofelt理论计算了该材料的强度参量．分析了钕离子激发态4F3／2的辐射寿命(631 μs)和4F3／2→4IJ′跃迁的受激发射截面和荧光分支比．     

不同入射角度下强流脉冲电子束能量沉积剖面和束流传输系数模拟计算

 强流脉冲电子束在材料中的能量沉积剖面、能量沉积系数和束流传输系数受其入射角的影响很大，理论计算了0.5~2.0MeV的电子束以不同的入射角在Al材料中的能量沉积剖面和能量沉积系数，并且还计算了0.4~1.4MeV电子束以不同入射角穿透不同厚度C靶的束流传输系数。计算结果表明，随着入射角的增大，靶材表面层单位质量中沉积的能量增大，电子在靶材料中穿透深度减小，能量沉积系数减小，相应的束流传输系数也减小；能量为0.5~2.0MeV的电子束当入射角在60°~70°时在材料表面层单位质量中沉积的能量较大。     

A Promising MoO_x-based Catalyst for n-Heptane Isomerization

The increasing demand for higher-octane gasoline and the regulations limiting the amount of aromatics in the fuel motivate the interest in catalytic isomerization of n-alkanes. In the last ten years, transition metal oxides or oxycarbides based on molybdenum or tungstate have attracted much attention due to their high activity and isomerization selectivity compared to the conventional bifunctional supported platinum catalyst and high resistance to sulphur and nitrogen catalyst poisons1-5. Ma…     

纳米氧化钛-乙二醇溶胶溶液的研究

选用了钛酸丁酯、硬脂酸和乙二醇作为表面活性剂，采用表面化学修饰和表面物理修饰2种方法修饰纳米氧化钛，然后分散在乙二醇溶剂中形成溶胶溶液．并通过红外光谱仪、紫外分光计、原子力显微镜，分析了表面化学修饰后的纳米氧化钛表面化学结构的变化，观测了纳米氧化钛溶胶在乙二醇溶剂中稳定性．试验结果表明表面活性剂与纳米氧化钛的表面的不饱和键之间形成了新的化学结构，粒子表面可能接枝上有机长链，提高了纳米粒子在溶剂中的相容性．表面化学修饰后的纳米氧化钛与乙二醇溶剂形成了较稳定的溶胶体系，而且纳米溶胶粒径较小．表面活性剂添加量与纳米粒子添加量控制在(1～1．2)：1时，可以获得纳米溶胶粒径较小，同时溶胶稳定性较好的纳米氧化钛-乙二醇溶胶体系．