Experimental observation of quantum corrections to electrical resistivity in nanocrystalline soft magnetic alloys

X-ray diffraction patterns of nanocrystalline Fe-Cu-Nb-Si-B (FINEMET) alloys reveal that bcc α-Fe/α-FeSi crystallites with the average grain size of 20(5) nm are dispersed in amorphous matrix. Enhanced electron—electron interaction (EEI) and quantum interference (QI) effects as well as electron-magnon (and/or electron-spin fluctuation) scattering turn out to be the main mechanisms that govern the temperature dependence of resistivity. Of all the inelastic scattering processes, inelastic electron-phonon scattering is the most effective mechanism to destroy phase coherence of electron wave functions. The diffusion constant, density of states at the Fermi level and the inelastic scattering time have been estimated, for the first time, for the alloys in question Article presented at the International Symposium on Advances in Superconductivity and Magnetism: Materials, Mechanisms and Devices, ASMM2D-2001, 25–28 September 2001, Mangalore, India.     

Study of the peak effect phenomenon in single crystals of 2H-NbSe2

The weakly pinned single crystals of the hexagonal 2H-NbSe₂ compound have emerged as prototypes for determining and characterizing the phase boundaries of the possible order-disorder transformations in the vortex matter. We present here a status report based on the ac and dc magnetization measurements of the peak effect phenomenon in three crystals of 2H-NbSe₂, in which the critical current densities vary over two orders of magnitude. We sketch the generic vortex phase diagram of a weakly pinned superconductor, which also utilizes theoretical proposals. We also establish the connection between the metastability effects and pinning.     

A novel method for the preparation of T3 free plasma/serum for routine RIA

A novel method to eliminate T₃ from gross sera/plasma based on prior treatment with 8-anilino-1-naphthalene sulphonic acid has been standardized. This method is rapid with a minimum loss of protein and uses only small quantities of charcoal. The treated sera have been tested for acceptance in the RIA system for routine assays.     

Critical points in the Bragg glass phase of a weakly pinned crystal of Ca3Rh4Sn13

New experimental data are presented on the scan rate dependence of the magnetization hysteresis width ΔM(H) (∞ critical current densityJ _c(H)) in isothermalMH scans in a weakly pinned single crystal of Ca₃Rh₄Sn₁₃, which displays second magnetization peak (SMP) anomaly as distinct from the peak effect (PE). We observe an interesting modulation in the field dependence of a parameter which purports to measure the dynamical annealing of the disordered bundles of vortices injected through the sample edges towards the destined equilibrium vortex state at a givenH. These data, in conjunction with the earlier observations made while studying the thermomagnetic history dependence inJ _c(H) in the tracing of the minor hysteresis loops, imply that the partially disordered state heals towards the more ordered state between the peak field of the SMP anomaly and the onset field of the PE. The vortex phase diagram in the given crystal of Ca₃Rh₄Sn₁₃ has been updated in the context of the notion of the phase coexistence of the ordered and disordered regions between the onset field of the SMP anomaly and the spinodal line located just prior to the irreversibility line. A multi-critical point and a critical point in the (H,T) region of the Bragg glass phase have been marked in this phase diagram and the observed behavior is discussed in the light of recent data on multi-critical point in the vortex phase diagram in a single crystal of Nb.     

Degradation process in organic thin film devices fabricated using P3HT

The stability of regioregular poly(3-hexylthiophene 2,5-diyl) (P3HT) thin films sandwiched between indium tin oxide (ITO) and aluminium (Al) electrodes have been investigated under normal environmental conditions (25°C and RH∼45–50%). Electrical and optical properties of ITO/P3HT/Al devices have been studied over a period of 30 days. Mobility μ of the order of 10⁻⁴ cm²/V-s has been obtained from the V ² law in the as-deposited P3HT films. Scanning electron microscopy (SEM) investigations show blistering of Al contacts in devices with a poly(3,4-ethylenedioxythiophene) (PEDOT) interlayer on application of voltage whereas no blistering is seen in devices without PEDOT. The results have been explained in terms of trap generation and propagation and the moisture-absorbing nature of PEDOT.      

AUTOMATED WIND TUNNEL MEASUREMENTS

It is common practice in power transmission to use bundled overhead electrical conductors because the lower rate of corona discharge, compared with single conductors, makes the bundle attractive for high voltages. However, secondary problems may arise from the vibrations induced by the aerodynamic forces which act on the leeward conductors as a result of their immersion in the wake of a windward conductor. Thus, in addition to possible aeolian and galloping oscillations observed for a single conductor, bundle conductors may also be subjected to wake-induced oscillations. ^1,2 Although extensive research has been done on the aeroelastic behavior of single and bundled conductors which are bare, little is known about the galloping or wake oscillation characteristics of given bundle conductors which, depending upon the environmental conditions during the formation of ice, may have five or so representative shaped cross-sections. One important task involves the aerodynamic quasi-static force and moment measurements in a wind tunnel using full scale conductor cross-sections each of which must be rotated through many angles at different spacings. Such measurements are repetitive as well as tediously time consuming and, hence, are beneficially automated. A reliable, accurate and inexpensive automated apparatus is described in this paper which permits the aerodynamic measurements to be performed efficiently and without intervention. Most importantly, it relieves the operator of the usual responsibility for manually controlling the separation and orientation of the sections as well as the need to manually compensate fluctuations in the free stream air speed. For simplicity, the apparatus is detailed in the context of a twin bundle conductor.     

Patents and literature

Protein engineering and site-directed mutagenesis is becoming immensely important in both fundamental studies and commercial applications involving proteins and enzymes in biocatalysis. Protein engineering has become a powerful tool to help biochemists and molecular enzymologists elucidate structure-function relationships in enzymic active sites, to understand the intricacies of protein folding and denaturation, and to alter the selectivity of enzymatic catalysis. Commercial applications of engineered enzymes are being developed to increase protein stability, widen or narrow substrate specificity, and to develop novel approaches for use of enzymes in organic synthesis, drug design, and clinical applications. In addition to protein engineering, novel expression systems have been designed to prepare large quantities of genetically engineered proteins. Recent US patents and scientific literature on protein engineering, site-directed mutagenesis, and protein expression systems related to protein engineering are surveyed. Patent abstracts are summarized individually and a list of literature references are given.     

Development of an optical fibre Al(III) sensor based on immobilised chrome azurol S

Chrome azurol S immobilised on XAD-2 has been used in this study as a reagent phase for the development of an optical fibre Al(III) sensor. Using a kinetic approach, this sensor was able to give a linear response in the Al(III) concentration range of 1.3 x 10(-5)-2.0 x 10(-4) M with a limit of detection of 1.0 x 10(-4) M. The optimum responses were obtained at pH 6.0 and when the solution was stirred. The sensor response was found to have a repeatability and reproducibility of 1.6% and 5.8%, respectively. The results obtained for Al(III) determination in aqueous sample were in good agreement with those obtained using graphite furnace-atomic absorption spectrometry.