Argon sorption and partial molar volume in poly(ethyl methacrylate) above and below the glass transition temperature

Sorption and dilation isotherms for argon in poly(ethyl methacrylate) (PEMA) are reported for pressures up to 50 atm over the temperature range 5–85°C. At temperatures below the glass transition (T_g=61°C), sorption isotherms are well described by the dual-mode sorption model; and isotherms above T_g follow Henry's law. However, isotherms for dilation due to sorption are linear in pressure at all temperatures over the range investigated. Partial molar volumes of Ar in PEMA are obtained from these isotherms. The volumes are approximately constant above T_g (about 40 cm³/mol), whereas the volumes below T_g are smaller and dependent on both temperature and concentration (19–26 cm³/mol). By analyzing the experimental data according to the dual-mode sorption and dilation model, the volume occupied by a dissolved Ar molecule and the mean size of microvoid in the glass are estimated to be 67 129 ų, respectively. The cohesive energy density of the polymer is also estimated as 61 cal/cm³ from the temperature dependence of the dual-mode parameters.     

Quantitative assessment of solid oxide electrochemical doping

Quantitative analysis of metal cation doping by solid oxide electrochemical doping (SOED) has been performed under galvanostatic doping conditions. A M–β″-Al₂O₃ (M=Ag, Na) microelectrode (contact radius: about 10 μm) was used as cation source to attain a homogeneous solid–solid contact between the β″-Al₂O₃ and doping target. In Ag doping into alkali borate glass, the measured dopant amount closely matched the theoretical value. High Faraday efficiencies of above 90% were obtained. This suggests that the dopant amount can be precisely controlled on a micromole scale by the electric charge during electrolysis. On the other hand, current efficiencies of Na doping into Bi₂Sr₂CaCu₂O_y (BSCCO) ceramics depended on the applied constant current. Efficiencies of above 80% were achieved at a constant current of 10 μA (1.6 A cm⁻²). The relatively low efficiencies were explained by the saturation of BSCCO grain boundaries with Na. By contrast, excess Na was detected on the anodic surface of ceramics at a constant current of 100 μA (16 A cm⁻²). In the present study, we demonstrate that SOED enables micromole-scale control over dopant amount.     

ELECTRON GUN FOR LARGE ORBIT GYROTRON (LOG) WITH DECREASED INFLUENCE OF CATHODE PLASMA ON ELECTRON BEAM PROPERTIES

High power Large Orbit Gyrotron (LOG) [1] is now under development at FIR FU. First version of this device was recently manufactured and then assembled with power supply ETIGO-IV [2]. Results of preliminary tests of electron-optic system are presented. The conditions when stableflat form of current pulse realized are discussed. Analytical estimations of cathode-anode distance to achieve small influence of cathode plasma during high voltage (HV) pulse are performed. Two new electron gun versions with decreased influence of the cathode plasma on its impedance and pulse form are suggested and optimized. New optimal magnetic field distributions are found. First gun has quiasi-flat cathode configuration near the anode diaphragm and provides operating current about 60 A. Second one uses blade cathode with operating current about 30 A. Beam quality for both guns is suitable for LOG operation.     

Electrical conducting and magnetic properties of (ethylenedithiotetrathiafulvalenothioquinone-1,3-diselenolemethide)2.FeBr4 (GaBr4) crystals with two different interlayer arrangements of donor molecules

Two donor molecules newly synthesized, dimethylthio- and ethylenedithio-tetrathiafulvalenothioquinone-1,3-diselenolemethides (1 and 2), were used to prepare their charge-transfer (CT) salts with a magnetic FeBr(4)(-) counteranion. For 1, a low electrical conducting 1:1 salt (1.FeBr(4)) was obtained, in which molecules of 1 are tightly dimerized in a one-dimensional (1D) stacking column. On the other hand, 2 gave a 2:1 salt (2(2).FeBr(4)) as two different kinds of plate crystals (I and II). Both I and II possess similar stacking structures of molecules of 2 in each 1D column with a half-cut pipelike structure along the c axis. However, for I, the stacking columns are aligned in the same direction along the a and b axes, while for II they are in the same direction along the a axis, but in the reverse direction along the b axis, resulting in the difference in the relative arrangement of molecules of 2 and FeBr(4)(-) ions between the two crystals. The room-temperature electrical conductivities of the single crystals of I and II were 13.6 and 12.7 S cm(-)(1), respectively. The electrical conducting behavior in I was metallic above 170 K but changed to be semiconducting with a very small activation energy of 7.0 meV in the temperature range 4-170 K. In contrast, II showed the semiconducting behavior in the whole temperature range 77-285 K. The corresponding nonmagnetic GaBr(4)(-) salts with almost the same crystal structure as I and II showed definitively different electrical conducting properties in the metal to semiconductor transition temperature in I as well as in the magnitude of activation energy in the semiconducting region of I and II. The interaction between the d spins of FeBr(4)(-) ions was weak and antiferromagnetic in both I and II, but the magnitude of the spin interaction was unexpectedly larger compared with that in the FeBr(4)(-) salt of the corresponding sulfur derivative of 2 with closer contact between the neighboring FeBr(4)(-) ions. These electrical conducting and magnetic results suggest a significant interaction between the conducting pi electrons and the d spins of FeBr(4)(-) ions located near the columns or layers.     

Synthesis of photoreactive polyimide having indan structure

Polyimide containing an indan unit and alkyl moiety with a high molecular weight was prepared from 5,7‐diamino‐1,1,4,6‐tetramethylindan and 3,3′,4,4′‐benzophenone tetracarboxylic dianhydride. This polyimide was amorphous and soluble in common organic solvents, such as tetrahydrofuran, chloroform, and cyclopentanone. Thermogravimetry of the polyimide showed good thermal stability, indicating that a 10% weight loss of the polyimide was observed at 500 °C in nitrogen. The glass‐transition temperature of the polyimide was not observed by DSC measurement between room temperature and 400 °C at a heating rate of 10 °C/min (Apparatus: DSC3100 MAC Science Co., Ltd.). Transparency of the polyimide at 365 nm was 80%. The polyimide acted as a photosensitive resist of negative type by UV radiation. The resist had a sensitivity of 31 mJ/cm² and a contrast of 2.3 when it was developed with cyclopentanone at room temperature. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 423–428, 2002     

Use of transition elements to enhance sensitivity for selenium determination by graphite-furnace atomic-absorption spectrophotometry combined with solvent extraction with the APDC-MIBK system

A microanalytical method for the measurement of selenium in waters and biological materials by a flameless atomic-absorption technique has been developed. The ammonium pyrrolidinedithiocarbamate-methyl isobutyl ketone extraction system is used for separation from interfering materials such as large amounts of alkali and alkaline earth metal salts and mineral acids. The atomic-absorption sensitivity for selenium is found to be enhanced to a large extent by co-extraction of some transition metal ions. Copper(II) has been used successfully as such an additive to diminish the volatility of selenium in the graphite furnace during the ashing step of the atomization cycle. When the aqueous phase/organic solvent volume ratio is 5 and the volume injected into the graphite furnace is 20 mul, the sensitivity for selenium is 0.3 ng/ml for 1% absorption. The relative standard deviation is ca. 2%. Interference by other metal ions is prevented by masking with EDTA. The method has been applied satisfactorily for the determination of minute amounts of selenium in waters and various biological materials.