Molecular ordering and 2D conductivity in ultrathin poly(3-hexylthiophene)/gold nanoparticle composite films

This paper reports the first comparison of the structure and electrical conductivity properties of spin cast (SC) and Langmuir-Schaeffer (LS) films of regioregular poly(3-hexylthiophene) (P3HT). In addition, the effect of incorporating highly monodisperse Au nanoparticles (NPs), with a core diameter of approximately 5 nm, into SC and LS P3HT films is described. A detailed picture of molecular organization in the films has been obtained using ultraviolet-visible absorption spectroscopy, atomic force microscopy, field-emission scanning electron microscopy, X-ray diffraction, and X-ray reflectivity. Film morphology was correlated with pseudo-two-dimensional conductivity measured using scanning electrochemical microscopy, with P3HT in the semiconducting regime. It was found that SC films, which were slightly thicker than those formed with the LS technique, exhibited greater organization. This resulted in an order of magnitude higher lateral conductivity for the SC films. Inclusion of Au NPs (50 wt %) into both SC and LS films resulted in the formation of uniform and relatively flat (rms roughness approximately 1 nm) composite films. Surprisingly, the addition of NPs did not disrupt the characteristic crystal structure found for the native P3HT films. The effect of Au NPs on film lateral conductivity was found to be determined by the distribution of Au NPs within the polymer, which varied significantly between SC and LS films. Whereas Au NPs aggregated into hexagonally packed clusters in SC films, NPs in LS films were predominantly uniformly distributed between the lamella bilayer. It was found that, while the inclusion of Au NPs caused the lateral conductivity to decrease in SC films, in LS films, the lateral conductivity increased by a factor of 2.     

Interfacial polymerisation of anilinium at Langmuir monolayers

Anilinium is strongly adsorbed at monolayers of the phospholipid L-alpha-dimyristoylphosphatidic acid (DMPA) and hexadecanesulfonic acid (HDSA) at the air-water interface, and undergoes chemical polymerisation under conditions where bulk polymerisation does not occur.     

Electrochemical templating of metal nanoparticles and nanowires on single-walled carbon nanotube networks

The use of single-walled carbon nanotube (SWNT) networks as templates for the electrodeposition of metal (Ag and Pt) nanostructures is described. Pristine SWNTs, grown on insulating SiO2 surfaces using catalyzed chemical vapor deposition, served as the working electrode. In the simplest case, electrical contact was made by depositing a gold strip on the SWNT substrate (device 1). Deposition of Ag and Pt over extensive periods (30 s) resulted in a high density of particles on the SWNTs, with almost contiguous nanowire formation from the Au/SWNT boundary moving to isolated nanoparticles at further distances from the contact. For direct electrochemical studies of Ag and Pt nucleation, the assembly was coated in a resist layer and a small window opened up to expose only the electrically connected SWNTs to solution (device 2). In this case, the electrochemical signature in voltammetric and amperometric studies of metal deposition was due solely to processes at the SWNTs. Coupled with high-resolution microscopy measurements (atomic force microscopy and field emission scanning electron microscopy), this approach provided detail on the nucleation and growth mechanisms of Ag and Pt on SWNTs under electrochemical control. In particular, Ag growth was found to be rapid and progressive with an increasing nanoparticle density with time, whereas Pt deposition was characterized by lower nucleation densities and slower growth rates with a tendency for larger particles to be produced over long times.     

Scanning electrochemical microscopy as a probe of Ag+ binding kinetics at Langmuir phospholipid monolayers

A new method has been developed for measuring local adsorption rates of metal ions at interfaces based on scanning electrochemical microscopy (SECM). The technique is illustrated with the example of Ag+ binding at Langmuir phospholipid monolayers formed at the water/air interface. Specifically, an inverted 25 microm diameter silver disc ultramicroelectrode (UME) was positioned in the subphase of a Langmuir trough, close to a dipalmitoyl phosphatidic acid (DPPA) monolayer, and used to generate Ag+ via Ag electro-oxidation. The method involved measuring the transient current-time response at the UME when the electrode was switched to a potential to electrogenerate Ag+. Since the Ag+/Ag couple is reversible, the response is highly sensitive to local mass transfer of Ag+ away from the electrode, which, in turn, is governed by the interaction of Ag+ with the monolayer. The methodology has been used to determine the influence of surface pressure on the adsorption of Ag+ ions at a phospholipid (dipalmitoyl phosphatidic acid) Langmuir monolayer. It is shown that the capacity for metal ion adsorption at the monolayer increased as the density of surface adsorption sites increased (by increasing the surface pressure). A model for mass transport and adsorption in this geometry has been developed to explain and characterise the adsorption process.     

A high-speed optical receiver

The design and performance of a high-speed optical receiver for the 1.3m and 1.5m wavelength regions is described. The receiver comprises an InGaAs PIN photodiode feeding into a bipolar transimpedance preamplifier. Measured receiver characteristics are found to compare favourably with theoretical predictions.     

Random Copolymers of 1,5-Dioxepan-2-one

ABSTRACT

Copolymers of 1,5-dioxepan-2-one (DXO) and e-caprolactone (?-CL), δ-valerolactone (δ-VL) or L-lactide (LLA) have been synthesized and characterized. High molecular weight copolymers were obtained using stannous-2-ethyl hexanoate as catalyst in bulk. Reactivity ratios for the copolymerization of DXO and δ-VL were determined at 110°C as r_VL=0.5 and r_DXO=2.3. At high conversion, depolymerization of δ-VL occurred, resulting in lower molecular weight and variations in the copolymer composition.

Physical properties, such as crystallinity and melting temperature of the DXO-copolymers proved to be strongly dependent on the choice of comonomer and on the molar composition of the copolymers. DXO appears to be incorporated into the poly-?-caprolactone (PCL) crystals and to some extent into the poly-δ-valerolactone (PVL) crystals, resulting in a more gradual decrease in crystallinity with increasing amount of DXO.     

Urological malignancies and the proteomic-genomic interface

The urological malignancies, renal, bladder and prostate cancer, account for approximately 16% of all cancer cases. Unfortunately 5-year survival rates are relatively poor, largely a result of many cases not being diagnosed before the tumour has metastasised. There is a clear need for the identification of markers which will allow earlier detection of disease, and predict prognosis and response to therapy. In addition, they may be of use as therapeutic targets. Current advances in molecular biology are allowing the identification of a number of tumour-associated changes which could be of clinical use in the future. However, with the rapid technological advances being made in the field of proteomics, this approach could be integrated with genomics providing a complementary alternative, overcoming disparities between mRNA levels and protein production, and additionally allowing the identification of tumour-associated post-translational modifications. These approaches have already been used to identify novel genes and other cancer-related changes involved in the pathogenesis of urological malignancies. This review describes current progress in the genomic and proteomic study of urological malignancies, and highlights the potential of using proteomic technologies in the study of this group of diseases.