STABILITY NUMBER IN SUBCLASSES OF P5-FREE GRAPHS

Two new hereditary classes of P5-free graphs where the stability number can be found in polynomial time are proposed. They generalize several known results.     

Resolving the copper interference effect on the stripping chronopotentiometric response of lead(II) obtained at bismuth film screen-printed electrode

As copper(II) is a common ion in a variety of analytical samples, its effect on the stripping response of lead(II) at bismuth film screen-printed carbon electrode (BFSPCE) was investigated. The study was conducted using a screen-printed three-electrode system (working, counter and reference electrodes), with the carbon-working electrode plated in situ with bismuth film. Copper present at significant concentration level in samples was found to affect the sensitivity of the electrode by reducing the constant current stripping chronopotentiometric (CCSCP) response of lead(II). Recovery of the lead stripping response at the BFSPCE in the presence of copper was obtained when 0.1 mM ferricyanide was added to the test solution. The ferricyanide added circumvents the detrimental effect of copper(II) by selectively masking the copper ions by forming a complex. The analytical utility of the procedure is illustrated by the stripping chronopotentiometric determinations of lead(II) in soil extracts.     

Gargano,Lewinter and Malerba问题的解

§1　IntroductionLet G be a graph with vertex-set V(G) ={ v1 ,v2 ,...,vn} .A labeling of G is a bijectionL:V(G)→{ 1,2 ,...,n} ,where L (vi) is the label of a vertex vi.A labeled graph is anordered pair (G,L) consisting of a graph G and its labeling L.Definition1.An increasing nonconsecutive path in a labeled graph(G,L) is a path(u1 ,u2 ,...,uk) in G such thatL(ui) + 1相似文献   

Stripping chronopotentiometric detection of copper using screen-printed three-electrode system—application to acetic-acid bioavailable fraction from soil samples

Single-use sensors, incorporating a three-electrode configuration (graphite carbon-working electrode; carbon-counter electrode and silver/silver chloride-reference electrode), have been fabricated on a polyester substrate using low cost screen-printing (thick-film) technology. These electrodes coupled with constant current stripping chronopotentiometry (CCSCP), has provided a convenient screening tool for on-site detection of trace levels of copper. Modification of the graphite carbon surface based on in situ deposition of mercury film has been carried out. By appropriate choice of supporting medium and applied constant stripping current, well-resolved and reproducible response for copper was obtained. The stripping response for copper following 2 min deposition was linear over the concentration range examined (10-2000 ppb) with detection limit of 6 ppb using 2 M hydrochloric acid (HCl). Successful applications of the sensing device to acetic-acid bioavailable fraction of a certified reference material (CRM 601, a lake sediment) and soil samples are demonstrated.     

Development and characterisation of disposable gold electrodes, and their use for lead(II) analysis

There is an increasing need to assess the harmful effects of heavy-metal-ion pollution on the environment. The ability to detect and measure toxic contaminants on site using simple, cost effective, and field-portable sensors is an important aspect of environmental protection and facilitating rapid decision making. A screen-printed gold sensor in a three-electrode configuration has been developed for analysis of lead(II) by square-wave stripping voltammetry (SWSV). The working electrode was fabricated with gold ink deposited by use of thick-film technology. Conditions affecting the lead stripping response were characterised and optimized. Experimental data indicated that chloride ions are important in lead deposition and subsequent analysis with this type of sensor. A linear concentration range of 10–50 μg L⁻¹ and 25–300 μg L⁻¹ with detection limits of 2 μg L⁻¹ and 5.8 μg L⁻¹ were obtained for lead(II) for measurement times of four and two minutes, respectively. The electrodes can be reused up to 20 times after cleaning with 0.5 mol L⁻¹ sulfuric acid. Interference of other metals with the response to lead were also examined to optimize the sensor response for analysis of environmental samples. The analytical utility of the sensor was demonstrated by applying the system to a variety of wastewater and soil sample extracts from polluted sites. The results are sufficient evidence of the feasibility of using these screen-printed gold electrodes for the determination of lead(II) in wastewater and soil extracts. For comparison purposes a mercury-film electrode and ICP–MS were used for validation.     

Development of surface chemistry for surface plasmon resonance based sensors for the detection of proteins and DNA molecules

The immobilisation of biological recognition elements onto a sensor chip surface is a crucial step for the construction of biosensors. While some of the optical biosensors utilise silicon dioxide as the sensor surface, most of the biosensor surfaces are coated with metals for transduction of the signal. Biological recognition elements such as proteins can be adsorbed spontaneously on metal or silicon dioxide substrates but this may denature the molecule and can result in either activity reduction or loss. Self assembled monolayers (SAMs) provide an effective method to protect the biological recognition elements from the sensor surface, thereby providing ligand immobilisation that enables the repeated binding and regeneration cycles to be performed without losing the immobilised ligand, as well as additionally helping to minimise non-specific adsorption. Therefore, in this study different surface chemistries were constructed on SPR sensor chips to investigate protein and DNA immobilisation on Au surfaces. A cysteamine surface and 1%, 10% and 100% mercaptoundecanoic acid (MUDA) coatings with or without dendrimer modification were utilised to construct the various sensor surfaces used in this investigation. A higher response was obtained for NeutrAvidin immobilisation on dendrimer modified surfaces compared to MUDA and cysteamine layers, however, protein or DNA capture responses on the immobilised NeutrAvidin did not show a similar higher response when dendrimer modified surfaces were used.     

翼型模型振动的实验研究与气动特性分析

通过在NF-3低速风洞专门研制的翼型模型及相应的俯仰和沉浮振动机构,选用NACA0012翼型进行大迎角下不同频率的振动实验,研究了模型振动平均状态下对其气动力特性的影响情况,并在N-S方程基础上对振动流场进行了初步分析。实验与计算研究的结果表明:在临近定常失速迎角的大迎角条件下,翼型的振动可以引起旋涡分离,导致翼型升力减小和失速迎角的提前;就所讨论的两种振动模式而言,俯仰振动的影响大于沉浮振动。所以,为了提高飞机模型,尤其是大展弦比飞机模型的风洞实验精准度,在模型设计和加工时要特别注意加强机翼弦向的扭转刚度。     

Stripping chronopotentiometric measurements of lead(II) and cadmium(II) in soils extracts and wastewaters using a bismuth film screen-printed electrode assembly

The key to remediative processes is the ability to measure toxic contaminants on-site using simple and cheap sensing devices, which are field-portable and can facilitate more rapid decision-making. A three-electrode configuration system has been fabricated using low-cost screen-printing (thick-film) technology and this coupled with a portable electrochemical instrument has provided a a relatively inexpensive on-site detector for trace levels of toxic metals. The carbon surface of the screen-printed working electrode is used as a substrate for in situ deposition of a metallic film of bismuth, which allows the electrochemical preconcentration of metal ions. Lead and cadmium were simultaneously detected using stripping chronopotentiometry at the bismuth film electrode. Detection limits of 8 and 10 ppb were obtained for cadmium(II) and lead(II), respectively, for a deposition time of 120 s. The developed method was applied to the determination of lead and cadmium in soils extracts and wastewaters obtained from polluted sites. For comparison purposes, a mercury film electrode and ICP-MS were also used for validation.     

A membrane-based immunosensor for the analysis of the herbicide isoproturon

A membrane based heterogeneous competitive enzyme-linked immunosorbent assay (ELISA) was used in this work to develop an immunosensor for the detection of a common herbicide, isoproturon. A screen-printed carbon working electrode with carbon counter and silver–silver chloride pseudo-reference electrode was utilized incorporating a membrane fixed into intimate contact with the working electrode to facilitate signal transduction. The membrane containing an immobilized isoproturon–ovalbumin conjugate was laminated onto the carbon working electrode and horseradish peroxidase (HRP) labeled polyclonal antibody was then applied for the competitive assay. Two different amperometric systems, hydroquinone and o-phenylenediamine (OPD) mediation reduction were utilised and the properties of the resultant sensors were compared. A flow injection apparatus was also developed utilising the immunosensor. Limits of detection for isoproturon (LLD₉₀) were found to be as low as 0.84 ng mL⁻¹. The senor was also validated using spiked extracted soil samples and also isoproturon contaminated samples.     

Urease–glutamic dehydrogenase biosensor for screening heavy metals in water and soil samples

A screen-printed three-electrode amperometric biosensor based on urease and the nicotinamide adenine dinucleotide hydrogen (NADH)–glutamic dehydrogenase system was developed and applied to the screening of heavy metals in environmental samples. The development of an amperometric sensor for the monitoring of urease activity was feasible by coupling the urea breakdown reaction catalysed by urease to the reductive ammination of ketoglutarate catalysed by glutamic dehydrogenase (GLDH). The ammonia provided by the urea conversion is required for the conversion of ketoglutarate to glutamate with the concomitant oxidation of the NADH cofactor. NADH oxidation is monitored amperometrically at 0.3 V (vs. Ag/AgCl) after urease immobilization onto the screen-printed three-electrode configuration. Immobilization of urease on the surface of screen-printed electrodes was performed by entrapment in alginate gel and adsorption on the electrode in a nafion film. Low sensitivity to inactivation by metals was recorded after urease entrapment in alginate gel with detection limits of 2.9 and 29.8 mg L^–1 for Hg(II) and Cu(II), respectively. The use of the negatively charged nafion film created a more concentrated environment of cations in proximity to the enzyme, thus enhancing the urease inhibition when compared to gel entrapment. The calculated detection limits were 63.6 and 55.3 g L^–1 for Hg(II) and Cu(II), respectively, and 4.3 mg L^–1 for Cd(II). A significant urease inactivation was recorded in the presence of trace amounts of metals (g L^–1) when the enzyme was used free in solution. Analysis of water and soil samples with the developed nafion-based sensor produced inhibition on urease activity according to their metal contents. The obtained results were in agreement with the standard methods employed for sample analysis. Nevertheless, the use of the amperometric assay (with free urease) proved more feasible for the screening of trace amounts of metals in polluted samples.