Biosorption of Chromium(III) by Biomass of Seaweed Sargassum sp. in a Fixed-Bed Column

This work aimed at modeling chromium biosorption using the biomass of seaweed Sargassum sp. in a fixed-bed column. The mathematical model used was obtained from the mass balance of the component in the liquid phase and in the biosorbent material. The effects of both axial dispersion in the column and the resistance to mass transfer in the solid were considered for the solution of the partial differential equations of the model, using the Galerkin method on finite elements. To represent the equilibrium data of the batch system the Langmuir isotherm were used. The chromium ion adsorption capacity of the seaweed Sargassum sp., at a temperature of 30°C and pH 3.5, was 2.61 mmol/g. The model performance was evaluated from experimental data obtained at 30°C for flow rates of 2, 6 and 8 mL/min. The parameters of the model, mass transfer and axial dispersion coefficients, were adjusted from these experimental data. The model proved adequate to describe chromium biosorption dynamics in fixed-bed columns.     

Linear calibration procedure for the phase-to-height relationship in phase measurement profilometry

Calibration of the relationship between height and phase is of uttermost importance to perform accurate 3D measurements in phase measurement profilometry. This work reports a different approach to this problem by first looking at the analytical expression for this relationship and determining the regime spanned by the fringe analysis method. The conclusions thus ascertained, amply justify confronting the analytical expression with a simple normalization procedure of the experimental data, with a remarkable matching between both results. In light of this, a linear calibration procedure with just one plane is proposed and verified experimentally.     

Mössbauer and infrared spectroscopic studies of novel mixed valence states in cobaltous ferrocyanides and ferricyanides

Novel mixed valence states have been obtained by the treatment of cobaltous ferrocyanides (Co⁺²Fe^II) and ferricyanides (Co⁺²Fe^III) in an ozone flow. The CN stretching bands occur at 2085 cm^–1 for Co⁺²Fe^II and at 2160 cm^–1 for Co⁺²Fe^III. After the ozonization process of Co⁺²Fe^II, an intense band approximately at 2125 cm^–1 is detected. This intermediate band must correspond to a mixed valence state of the type: Fe^II–CN–Co²⁺–NC–Fe^III Mössbauer spectra recorded in situ during the ozonization of Co⁺²Fe^II show the presence of two components: a doublet with isomer shift and quadrupole splitting values close to the cobalti ferricyanide and a very broad line for the mixed valence state. From the Mössbauer and infrared spectra of the aged samples of the Co⁺²Fe^II after ozonization, a relaxation process to the initial state of the samples is observed but the mixed valence state is stable.     

Determination of volatile corrosion inhibitors by capillary electrophoresis

In this work, a capillary electrophoresis (CE) method using indirect UV detection (214nm) for the simultaneous determination of monoethanolamine (MEA), diethanolamine (DEA), triethanolamine (TEA), diethylethanolamine (DEEA), monocyclohexylamine (MCHA) and dicyclohexylamine (DCHA) in water/ethanol extracts of wrapping materials containing volatile corrosion inhibitors (VCIs) was described. A running buffer consisting of 0.010 molL(-1) imidazole, 0.010 molL(-1) 2-hydroxyisobutyric acid (HIBA) and 0.010 molL(-1) 18-crown-6 ether enabled separation of the analytes in less than 7 min. A few method validation parameters were determined revealing good migration time repeatability (<0.7% RSD) and area repeatability (< 1.8% RSD). Limits of detection were in the range of 0.52-1.54 mg L(-1). Recovery values were in the range of 94.8-100.9%. The methodology was successfully applied to the analysis of three commercial products (VCI treated paper, foam and plastic). The concentration of amines in these materials varied from 0.050 to 22.3% (w/w).     

Copper determination in biological materials by ETAAS using W-Rh permanent modifier

A tungsten-rhodium treatment on the integrated platform of a transversely heated graphite atomiser was used as a permanent chemical modifier for the determination of copper in biological materials by using digested samples as well as slurry sampling in electrothermal atomic absorption spectrometry. The W-Rh permanent modifier was as efficient as Pd+Mg(NO(3))(2) conventional modifier for obtaining good Cu thermal stabilisation in the digested and slurry samples. The permanent W-Rh modifier remained stable by approximately 300 and 250 firings when 20 mul of digested sample and 20 mul of slurry were delivered into the atomiser, respectively. In addition, the permanent modifier increased the tube lifetime up to 1370 and 744 analytical measurements in the digested and slurry samples, respectively. Also, when the W-Rh permanent modifier was employed, there was less variation of the slope of the analytical curves during the total atomiser lifetime, resulting in a decreased need of re-calibration during routine analysis, increasing the sample throughput, and consequently diminishing the variable analytical costs. Detection limits obtained with W-Rh permanent modifier were 0.64 and 0.33 mug g(-1) Cu for digested (dilution factor 100 ml g(-1)) and 1.0% m/v slurries of biological materials, respectively. Results for the determination of copper in the samples were in agreement with those obtained with decomposed sample solutions by using Pd+Mg(NO(3)), since no statistical differences were found after applying the paired t-test at the 95% level.