In situ spectroscopic study of the oxidation and reduction of Pd(111)

Using a photoemission spectroscometer that operates close to ambient conditions of pressure and temperature we have determined the Pd-O phase diagram and the kinetic parameters of phase transformations. We found that on the (111) surface oxidation proceeds by formation of stable and metastable structures. As the chemical potential of O2 increases chemisorbed oxygen forms followed by a thin surface oxide. Bulk oxidation is a two-step process that starts with the metastable growth of the surface oxide into the bulk, followed by a first-order transformation to PdO.     

Atomic force microscopy study of beta-substituted-T7 oligothiophene films on mica: mechanical properties and humidity-dependent phases

The structural and mechanical properties of Langmuir-Blodgett monolayer and multilayer films of 3",4"-didecyl-5,2'; 5',2"; 5",2'; 5',2"; 5",2''; 5'',2"-heptathiophene-4'-acetic acid on mica have been studied by atomic force microscopy (AFM) as a function of humidity, temperature, and applied force. The molecules orient with the carboxylic acid group pointing toward the mica surface and expose the alkyl side chains to the air interface. As the load applied by the AFM tip increases, the film is compressed easily from an initial height of 2 to 1.2 nm. After compression the films can support much higher loads without loss of height. The state of aggregation of the molecules was found to be sensitive to the environmental humidity, which induced reversible changes. Annealing the samples with monolayer or multilayer films resulted in irreversible changes when the temperature exceeded approximately 100 degrees C.     

Chemical reactions of water molecules on Ru(0 0 0 1) induced by selective excitation of vibrational modes

Tunneling electrons in a scanning tunneling microscope were used to excite specific vibrational quantum states of adsorbed water and hydroxyl molecules on a Ru(0 0 0 1) surface. The excited molecules relaxed by transfer of energy to lower energy modes, resulting in diffusion, dissociation, desorption, and surface-tip transfer processes. Diffusion of H₂O molecules could be induced by excitation of the O-H stretch vibration mode at 445 meV. Isolated molecules required excitation of one single quantum while molecules bonded to a C atom required at least two quanta. Dissociation of single H₂O molecules into H and OH required electron energies of 1 eV or higher while dissociation of OH required at least 2 eV electrons. In contrast, water molecules forming part of a cluster could be dissociated with electron energies of 0.5 eV.     

A General Equation for Fitting Contact Area and Friction vs Load Measurements

The variation of contact area with load between adhesive elastic spheres depends upon the effective range of attractive surface forces. Relatively simple forms to describe limiting cases exist, but the general intermediate case requires a more complex analysis. Maugis, using a Dugdale model [D. Maugis, J. Colloid. Interf. Sci. 150, 243 (1992)], provides an analytic solution, but the resulting equations are cumbersome if one wishes to compare with experimental data such as atomic force microscope measurements. In this paper we present a simpler general equation that approximates Maugis' solution extremely closely. The general equation is amenable to conventional curve fitting software routines and provides a rapid method of determining the value of the "transition parameter" which describes the range of surface forces. Copyright 1999 Academic Press.     

The influence of sulfur adsorption on the step structure of vicinal Mo(100): a LEED and STM study

The effect of sulfur adsorption on the step structure of vicinal Mo(100) surfaces has been studied with scanning tunneling microscopy (STM) and low energy electron diffraction (LEED). STM was used for low densities of steps on a nominally flat (100) surface. LEED was used to study the more highly and regularly stepped (910), (911), and (28,4,1) oriented surfaces. Steps and the sulfur adsorbate were found to have a strong interaction. The presence and orientation of steps on the surface governed the formation of ordered domains of sulfur, and sulfur modified the structure of the steps on the surface. Both techniques show that monatomic steps predominate on the clean surfaces. When sulfur was adsorbed on the surfaces, however, steps coalesced to form groups of steps, double atomic height steps, and multiple height steps, depending on sulfur coverage and initial step density. The results are discussed in the framework of the theory of equilibrium crystal shape and provide information on how the Mo step-step interactions are affected by sulfur adsorption.