Improved detectability with a polymer-based trapping device in rapid HPLC analysis for ultra-low levels of bisphenol A (BPA) in environmental samples.

A new high-performance liquid chromatography (HPLC) method has been developed to detect ultra-low concentrations of bisphenol-A (BPA) (below 1 ng/L (ppt)) using column switching electrochemical detection (ECD). The results were superior to those obtained from manual pretreatment procedure with membrane stationary phase. BPA is inherently ubiquitous in the environment, including tools and solvents used for its analysis; to obtain meaningful results, therefore, the concentration of the overall BPA contamination must be below the detection limit for BPA using the analytical system. Therefore, purified water for preparing the standard BPA solution must be filtered with a hydrophobic membrane to suppress BPA background levels of contamination. In addition, we investigated methods for effectively preserving environmental water containing BPA. The addition of a small amount of ethylenediaminetetraacetic acid (EDTA) provided good recovery even after overnight storage. By employing these precautionary measures and procedures to reduce BPA contamination from the analytical procedure, we could accurately determine l(-10) ppt of BPA in environmental water samples using a column switching HPLC system.     

Development and features of hydro-membrane gas chromatography.

Hydro-membrane gas chromatography (HMGC) is achieved by the annular condensation of water in a capillary column at less than 70 degrees C. The annular membrane of water is formed as a result of the wettability of the stationary phase, which is induced at a water contact angle ranging from 75 degrees to 79 degrees, as derived from a solubility parameter (delta) range of 15.7 +/- 0.3 MPa(1/2) of the coated resin. The range of the liquid to gas volume ratio (beta) required to support the annular membrane should be kept between 0.00005 and 0.0003. In the case of a 0.25-mm i.d. column, the ratio can be set by the combination of a 0.1 to 0.2 microl min(-1) water supply rate and helium gas flow rate. Separation by HMGC develops not only a gas-solid partition but also a focusing effect on the water membrane. One feature of HMGC is that it gives a non-adsorption chromatogram based on the blocking effect of pre-adsorbed water; furthermore, despite the presence of a relatively large quantity of water, the electron impact ionization efficiency is kept the same as in the usual GC/MS condition. The detection limit with the injection of 1 microl of aquatic solution was estimated to be less than 0.1 ppb of low-molecular-weight fatty acids with s/n = 5 on a mass chromatogram at m/z 45. The HMGC/EI-MS system can be applied to the trace analysis of C1 to C3 volatile acids, volatile inorganic acids, and halogenated organic acids in water.     

Basic study of the gelation of dimethacrylate‐type crosslinking agents

An investigation was made of the gelation of dimethacrylate‐type crosslinking agents in view of an application for separation media. The study mainly centered on a crosslinking agent, glycerol dimethacrylate (GDMA), which is relatively hydrophilic because of a hydroxyl group in the middle of its structure. The gelation of GDMA was compared with that of other hydrophobic crosslinking agents such as ethylene glycol dimethacrylate and 1,6‐hexanediol dimethacrylate. The diluents used in the study were toluene, toluene with methanol, and cyclohexanol. The gelation was observed in real time with a charge coupled device camera and dynamic light scattering (DLS). Also, the separated dry gels were extensively characterized with scanning electron microscopy, BET (N₂ absorption and desorption isotherm), and Fourier transform infrared. DLS analysis showed a stronger molecular interaction of GDMA gelation in toluene, whereas this interaction was much weaker in an alcoholic solvent such as toluene with methanol or cyclohexanol. This indicated that GDMA gelation might proceed through hydrogen bonding as well as a crosslinking reaction of vinyl groups. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 949–958, 2006     

Frequency measuring system using mirror gap stabilized Fabry-Perot interferometer

The mirror gap of a Fabry-Perot interferometer was stabilized with two laser diodes; one locked to the line frequency 385,243,555.14445 MHz of the F=3<--1 in 5D(3/2)<--5S(1/2) (87Rb) and the other to the 385,284,566.3663 MHz of the F=4<--2 in 5D(5/2)<--5S(1/2) (87Rb) [Opt. Commun. 102 (1993) 432]. The length of the mirror gap was adjusted to generate the zero-cross points simultaneously at both of the two line positions. The fringe signals obtained from an interferometer thus stabilized can be used as frequency markers having accuracies of the order of 10(10) depending on the finesse of the interferometer used. Based on measurement using Cs D1 hyperfine lines reported by Udem et al. [Phys. Rev. Lett. 82 (1999) 3568], the uncertainty of markers in the region 50 THz apart from the reference lines is +/- 5 MHz.     

Stereochemistry of cholesterol hydroxylation at C-22 during pregnenolone biosynthesis

Cholesterol and 20-hydroxycholesterol labelled at C-22 stereospecifically by deuterium were incubated with the enzyme of bovine adrenocortical mitochondria. The results indicated that hydroxylation occurs with retention of the configuration of C-22 to give exclusively the 22R stereoisomers of 22-hydroxy- and/or 20,22-dihydroxycholesterol.     

Preparation of 2-fluoromalonic esters and related compounds from hexafluoropropene

Dimethyl and diethyl fluoromalonates were prepared from hexafluoropropene by its exhaustive alcoholysis or alternatively its ammonolysis and alcoholysis. Fluoromalonates thus obtained or their alkylated derivatives were condensed with o-phenylenediamine or its substituted derivatives to give a number of 1H-3-fluoro-1,5-dibenzodiazepin-2,4(3H,5H)-diones.     

Preparation of a thermally phase-separating copolymer,poly(N-isopropylacrylamide-co-N-acryloxysuccinimide), with a controlled number of active esters per polymer chain

N-isopropylacrylamide and N-acryloxysuccinimide have been copolymerized in various mixtures of terrahydrofuran and toluene using azobisisobutyronitrile as initiator. Polymerization has been conducted for 24 h at 50°C under a slightly positive pressure of nitrogen. The copolymers were assayed for active ester content by measuring the UV absorbance (259 nm) of N-hydroxysuccinimide anion, generated by reacting the copolymers with N-isopropylamine in dimethylformamide and dissolving the resulting mixture in 0.1M HEPES buffer, pH 7.5. The molecular weight and its distribution have been estimated by gel permeation chromatography. The active ester content was found to be equivalent to the comonomer feed ratio, and the major factor controlling the molecular weight was the ratio of tetrahydrofuran to toluene. Thus, the number of active esters per polymer chain could be controlled by adjustment of the comonomer feed ratio and the ratio of tetrahydrofuran to toluene. Monomer reactivity ratios for copolymerization of N-isopropylacrylamide with N-acryloxysuccinimide were also estimated. These copolymers are useful for immobilizing binding ligands such as antibodies for subsequent thermally induced precipitation immunoassays and bioseparation processes.     

A large deviation principle for (r,p)-capacities on the Wiener space

Summary We formulate and prove a large deviation principle for the (r, p)-capacity on an abstract Wiener space. As an application, we obtain a sharpening of Strassen's law of the iterated logarithm in terms of the capacity.     

Leaching behavior of metal-containing species in residual oils with different organic solvents

The leaching behavior of two different residual oils is investigated with 24 organic solvents including alkanes, aromatics, esters, ethers ketones, alcohols and nitrogen compounds. A 2-g portion of sample oil is shaken with 20 ml of the organic solvent. The leaching of the organic matrix of the oil is determined by weighing the dissolved organic matrix after removal of solvent. The leaching of vanadium, iron and nickel was determined by flame atomic absorption spectrophotometry after ashing of the dissolved fraction. The leaching of those metals depends strongly on the solvent used; for example, vanadine is almost completely leached into toluene, but only slightly into methanol. The leaching of iron is poor compared with that of vanadium or nickel. In most solvents, leaching of those metal-containing species is poorer than that of organic material. Exceptionally, N,N-dimethylformamide is more efficient in leaching vanadium species than organic material.