Development of 1-(2-pyridylazo)-2-naphthol-modified polymeric membranes for the effective batch pre-concentration and determination of zinc traces with flame atomic absorption spectrometry

The development of 1-(2-pyridylazo)-2-naphthol (PAN)-modified polymeric membranes for the effective batch pre-concentration and determination of zinc traces with flame atomic absorption spectrometry (FAAS) is described. The method is based on the chemical bonding of the metal species with a suitable ligand, which has been immobilized into a water-insoluble cellulose acetate (CA) membrane followed by simple rinsing of the chelating agent-metal complex with an acidified methanolic solution. The latter is directly aspirated to the nebulizer of a FAA spectrophotometer without any other treatment. As an analytical demonstration, trace concentrations of Zn(II) were successfully detected in real samples, such as seawater, river and lake water, wastewater as well as in a reference material, without any laborious and time-consuming treatment. Several working parameters were investigated. A pre-concentration factor of 100 was achieved by simple immersing of a circular piece of the CA-PAN membrane (0.6 cm diameter) in the tested samples for 30 min at room temperature. The analytical curve was rectilinear up to 30 mug l(-1) zinc with detection limit of 0.7 mug l(-1), a quantitation limit of 2.0 mug l(-1) and a relative standard deviation lower than 2%.     

Spectrophotometric Determination of Trace Amounts of Vanadium Based on its Catalytic Effect on the Reaction of Diphenylamine and Hydrogen Peroxide

 In this work a kinetic spectrophotometric method for the determination of trace amounts of vanadium is presented. The method is based on the catalytic effect of the vanadium(V) on the reaction between diphenylamine (DPhA) and hydrogen peroxide in a concentrated solution of formic acid. The formation of the deep-blue oxidation product is followed by a filter spectrophotometer, equipped with an optical fiber assembly, on line with a PC provided with the suitable software. The measurements were taken at 583 nm, with an immersed type cell of 1 cm light path length. The optimization of the operating conditions regarding concentrations of the reagents, temperature and interferences are also investigated. The working curve is linear over the concentration range 0.40–4.0 μg/ml vanadium(V). The relative standard deviation for a standard solution of 0.6 μg/ml of vanadium is 0.5% (n = 5). The proposed method proved highly sensitive, selective and relatively rapid for the assay of vanadium, at low level of 0.40 μg/ml without any pre-concentration step. The method was applied to alloys and cosmetics samples. The results were compared to those received with a reference method. Good agreement was attained, with a mean error of 0.5%. Received February 25, 2000. Revision May 15, 2000.     

Spectrophotometric kinetic determination of copper(II) trace amounts based on its catalytic effect on the reaction of the reduced 2,6-dichlorophenolindophenol and hydrogen peroxide

A catalytic spectrophotometric method is presented for the determination of Cu(II), based on the oxidation of the leucocompound of the 2.6-dichlorophenolindophenol (DCPI)(r), in the presence of hydrogen peroxide and the catalytic effect of Cu(II) on this reaction in ammonia-ammonium chloride buffer solution of pH 10.5. The above reaction is followed spectrophotometrically at 562 nm. The study was carried out with a filter spectrophotometer equipped with a fiber optic and an immersed type optical cell of 1 cm. The optimum operating conditions regarding concentration of the reagents involved, pH and temperature were established. The interference effect of several metallic species was also investigated. It was found that the proposed method shows fairly good selectivity and sensitivity, simplicity and rapidity compared to other kinetic methods. The working curve of the recommended reaction-rate method is linear in the concentration range 5-300 ng/ml. The relative standard deviation for a standard solution of 30 ng/ml Cu(II) is better than 2.5%. The method was applied successfully on the determination of Cu(II) in a wide variety of real samples such as alloys, pharmaceuticals, foodstuffs and environmental samples. The results were compared to those received with official methods. Good agreement was attained.     

Comparative study of different types of graphenes as electrocatalysts for ascorbic acid

A comparative study regarding the electrocatalytic activity of graphene oxide (GO), chemically-reduced graphene oxide (crGO) and graphene produced by direct liquid exfoliation (dG) is presented. Sensors were developed by modifying glassy carbon (GC) electrodes with GO, crGO and dG and ascorbic acid was used as a pilot analyte. GC/GO electrodes offer substantially lower oxidation overpotential, up to 350 mV, compared with GC/crGO, GC/dG and unmodified GC electrodes. In addition, the different carbon-to-oxygen atomic ratios in GO, as it occurs depending on the synthetic route, were found to have a remarkable effect on the performance of the sensors. Reduction of GO was achieved by immersing the modified electrodes into a stirred solution of NaBH₄ for 10 min at room temperature. This process was used alternatively of the time consuming and laborious process of hydrazine, and its effectiveness was confirmed by cyclic voltammetry and electrochemical impedance spectroscopy. Analytical utility of the sensors is demonstrated.     

Construction of a Triphenyltetrazolium Liquid Membrane Ion Selective Electrode and its Analytical Application to the Assay of Vitamin C

 The construction of a liquid triphenyltetrazolium cation (TT⁺) ion-selective electrode (ISE) based on [TT⁺]₃[P(W₃O₁₀)₄] salt dissolved in 2-nitrotoluene is described. The liquid membrane electrode exhibits a rapid and almost Nernstian response to triphenyltetrazolium cations in the concentration range from 2×10⁻⁴ to 1×10⁻² mol l⁻¹. The Nernstian slope is 56–58 mV decade⁻¹ which remains constant for at least two months. The response is virtually unaffected by pH changes in the range 3–12. Major interferents are periodate and malate. Deviation from linearity is also observed in the presence of bromide, iodide and thiocyanate, due to their precipitation with triphenyltetrazolium cations. Analytical applications such as direct potentiometry for the determination of TT⁺ in aqueous solutions and indirect potentiometry for the assay of ascorbic acid (vitamin C) in pharmaceutical preparations are described. Ascorbic acid in the range of 150–500 mg l⁻¹, under specified experimental conditions, can be determined with mean relative error of 1.9%. Received February 25, 2000. Revision April 4, 2000.     

Synthesis, characterization and performance of vanadium hexacyanoferrate as electrocatalyst of H2O2

The present work reports for the first time on the synthesis, characterization and performance of vanadium hexacyanoferrate (VHCF) as electrocatalyst of hydrogen peroxide. VHCF was synthesized by mixing V₂O₅ · nH₂O xerogel with ascorbic acid and K₄[Fe(CN)₆] in double distilled water. X-ray powder diffraction, energy dispersive spectroscopy, scanning electron microscopy, and IR-spectroscopy data suggest the formation of nanocrystalline (mean crystal size 11 nm) compound with a tentative molecular formula K₂(VO)₃[Fe(CN)₆]₂. Composite films of VHCF with poly(vinyl alcohol) were developed over a glassy carbon electrode, and then covered with different (neutral, positively or negatively charged) membranes. The effect of each membrane on the working stability of the resultant sensors was evaluated. Cyclic voltammetry experiments showed that composite films exhibit a pair of reversible redox peaks, and a remarkable low potential electrocatalysis on both the reduction and oxidation of hydrogen peroxide. A linear calibration curve over the concentration range 0.01–3.0 mM H₂O₂ was constructed. Limit of detection (S/N = 3) of 4 μM H₂O₂ was calculated. The proposed transducer is quite selective to hydrogen peroxide. No response was observed in the presence of 10 mM ascorbic acid.     

Ultrasensitive Determination of Vitamin B12 Using Disposable Graphite Screen‐Printed Electrodes and Anodic Adsorptive Voltammetry

A facile, rapid and ultra‐sensitive method for the determination of vitamin B₁₂ (cyanocobalamin) at the sub‐nanomolar concentration range by using low‐cost, disposable graphite screen‐printed electrodes is described. The method is based on the cathodic preconcentration of square planar vitamin B_12s, as occurred due to the electro reduction of Co(III) center in vitamin B_12a to Co(I), at ?1.3 V versus Ag/AgCl/3 M KCl for 40 s. Then, an anodic square wave scan was applied and the height of the peak appeared at ca. ?0.73 V versus Ag/AgCl/3 M KCl, due to the oxidation of Co(I) to Co(II) in the adsorbed molecule, was related to the concentration of the vitamin B₁₂ in the sample. EDTA was found to serve as a key‐component of the electrolyte by eliminating the background signal caused by metal cations impurities contained in the electrolyte (0.1 M phosphate buffer in 0.1 M KCl, pH 3). It also blocks trace metals contained in real samples, thus eliminating their interference effect. The method was optimized to various working parameters and under the selected conditions the calibration curve was linear over the range 1×10^?10–8×10^?9 mol L^?1 vitamin B₁₂ (R²=0.994), while the limit of detection for a signal‐to‐noise ratio of 3 (7×10^?11 mol L^?1 vitamin B₁₂) is the lowest value of any reported in the literature for the electrochemical determination of vitamin B₁₂. The sensors were successfully applied to the determination of vitamin B₁₂ in pharmaceutical products.     

Palladium nanoparticle-decorated iron nanotubes hosted in a polycarbonate porous membrane: development, characterization, and performance as electrocatalysts of ascorbic acid

One-dimensional iron metallic nanotubes were prepared by electroless deposition within the pores of polycarbonate (PC) membranes. The longitudinal nucleation of the nanotubes along the pore walls was achieved by mounting the PC membrane between two halves of a U-shaped reaction tube. Palladium nanoparticles were post-deposited on the inner wall of the nanotubes. The composition, morphology, and structure of the Pd/Fe nanotubes were characterized by transmission electron microscopy, scanning electron microscopy, and inductively coupled plasma-atomic emission spectroscopy. A glassy carbon (GC) electrode modified with the free Pd/Fe bimetallic nanotubes (isolated after the dissolution of the host membranes) showed small improvement on the overpotential oxidation of ascorbic acid in comparison to the bare GC electrode. Alternatively, the Pd/Fe-polycarbonate membrane was covered with a sputtered gold thin layer of 10?nm from one side and mounted in a homemade electrochemical cell acting as the working electrode. The potential use of these functional membranes as catalytic surfaces for the electrochemical monitoring of ascorbic acid was investigated by cyclic voltammetry and amperometry. In the presence of a phosphate buffer solution, pH?7, Pd/Fe-polycarbonate membranes showed excellent electrocatalytic properties toward the oxidation of ascorbic acid even at potentials as low as 0?mV versus a Ag/AgCl reference electrode. In addition to the substantial lower overpotential, these electrodes offered selectivity over acetaminophen and uric acid, and a prolonged working stability without the need for maintenance. The electrodes were kept dry between different working days and retained their original activity for more than 1?week. Pd-polycarbonate and Fe-polycarbonate membranes were also developed for comparison purposes.     

Membrane sampler for interference-free flow injection NO determination in biological fluids with chemiluminescence detection

The development of a chemiluminescence (CL) method based on the perm-selective properties of a Nafion–cellulose acetate (CA) composite membrane for the monitoring of nitric oxide (NO) in biological fluids is described. Horseradish peroxidase (HRP) was used as NO trapping solution, forming the stable compound HRP–NO. The HRP was denatured and the trapped NO was released and detected by using the luminol–H₂O₂ system. Using a mixed (size-exclusion and polar-based) transport control, the interference effects of various compounds were minimized. The method was used for NO monitoring in simulated samples, by using a blood specimen as sample matrix. The 3σ detection limit is 0.9×10⁻⁶ mol and linear semi-log calibration plot in the range 1.8×10⁻⁶ to 2.7×10⁻³ mol NO was constructed. The applied methodology was further used to prolong the NO lifetime in order to increase the sensitivity of its determination. This was based on the increase of the response in the presence of certain reductive species, which act as NO preservatives in biological fluid samples.     

Kappa-casein based electrochemical and surface plasmon resonance biosensors for the assessment of the clotting activity of rennet

We report for the first time the development of kappa-casein (κ-CN)-based electrochemical and surface plasmon resonance (SPR) biosensors for the assessment of the clotting activity of rennet. Electrochemical biosensors were developed over gold electrodes modified with a self-assembled monolayer of dithiobis-N-succinimidyl propionate, while SPR measurements were performed on regenerated carboxymethylated dextran gold surfaces. In both types of biosensor, κ-CN molecules were immobilized onto modified gold surfaces through covalent bonding. In electrochemical biosensors, interactions between the immobilized κ-CN molecules and chymosin (the active component of rennet) were studied by performing cyclic voltammetry, differential pulsed voltammetry, and electrochemical impedance spectroscopy (EIS) measurements, using hexacyanoferrate(II)/(III) couple as a redox probe. κ-CN is cleaved by rennet at the Phe105–Met106 bond, producing a soluble glycomacropeptide, which is released to the electrolyte, and the positively charged insoluble para-κ-casein molecule, which remains attached to the surface of the electrode. This induced reduction of the net negative charge of the sensing surface, along with the partial degradation of the sensing layer, results in an increase of the flux of the redox probe, which exists in the solution, and consequently, to signal variations, which are associated with the increased electrocatalysis of the hexacyanoferrate(II)/(III) couple on the gold surface. SPR experiments were performed in the absence of the redox probe and the observed SPR angle alterations were solely attributed to the cleavage of the immobilized κ-CN molecules. Various experimental variables were investigated and under the selected conditions the proposed biosensors were successfully tried to real samples. The ratios of the clotting power units in various commercial solid or liquid samples, as they are calculated by the EIS-based data, were almost identical to those obtained with a reference method. In addition, EIS measurements showed an excellent reproducibility, lower than 5%.