Evaluation of PLE exhaustiveness for the extraction of PCBs from sediments and the influence of sediment characteristics

Pressurized liquid extractions were performed on eight sediments in order to investigate if a modified US EPA method (100 °C, 100 bar, n-heptane/acetone (1:1), 2 × 5 min) provided exhaustive extractions of polychlorinated biphenyls (PCBs) from sediment, and to study if the extractability of PCBs from the different sediments was affected by characteristics of the sediment. The recovery from the eight native sediments, contaminated in nature, was between 96.4% and 98.9%, as an average of the recoveries from 10 PCB congeners. Hundred percent recovery was defined as the sum of two consecutive extractions (2 × 5 min each) at the stated conditions. The recoveries of the individual congeners were above 94%, except for one congener in one sediment, which had a recovery of 92%. When the recoveries and different characteristics of the sediments were compared, no correlation appeared between recoveries and sediment PCB concentration, total organic carbon (TOC), soot carbon (SC) or amorphous carbon (AC). The fact that carbon did not influence the extractions was somewhat surprising, since previous experiments have indicated a connection. Instead, statistically significant (p < 0.05) correlations were observed for water content and carbon/nitrogen (C/N) ratio. The decrease in recoveries with decreased water content was attributed to less access of the solvent to the analytes due to less matrix swelling. The lowered recoveries with increased C/N ratio can indicate that a difference in structure of the organic matter exists, which influences the binding strength between the analytes and the matrix. The difference in structure can possibly be explained by different origin of the organic matter or by aging effects. Overall the method was found to be exhaustive and the excellent recoveries show that sediment characteristics do not influence the extractions markedly.     

The contribution of the pressure drop to analyte retention in coupled column supercritical fluid chromatography of lipids

Summary This paper reports the qualitative and quantitative effects of the column pressure drop on the retention of lipid components in a serially coupled capillary column SFC system. The contribution of the pressure drop consists of two components, the density effect and the flow effect. The magnitude of the flow effect,i. e. the change in retention which results from changes in the flow-rate when column pressures are changed, is determined by the difference in single column analyte k values. The effect will be positive compared with the uncorrected retention values when the column with largest k value is closest to the injector. With the columns in reversed order, the effect will be negative. The contribution from the density effect always resulted in larger coupled column k values and was in most instances of more significance than the flow effect component. Values calculated with and without pressure drop correction have been compared and it has been shown that for most of the eighteen model lipid compounds investigated, the deviations from the experimental retention factors were smaller when pressure drop corrections were made.     

Stress development during drying of calcium carbonate suspensions containing carboxymethylcellulose and latex particles

Stress development during drying of coatings produced from aqueous dispersions of calcium carbonate particles in the presence and absence of organic binders was studied using a controlled-environment stress apparatus that simultaneously monitored drying stress, weight loss, and relative humidity. Specifically, the influence of two organic binders on drying stress evolution was investigated: (1) carboxymethylcellulose, a water-soluble viscosifying aid, and (2) a styrene-butadiene latex emulsion of varying glass transition temperature. The stress histories exhibited three distinct regions. First, a period of stress rise was observed, which reflected the capillary tension exerted by the liquid on the particle network. Second, a maximum stress was observed. Third, it was followed by a period of either stress decay or rise depending on the organic species present. Significant differences in stress histories were observed between coatings containing soluble and nonsoluble binders. Maximum drying stresses (sigmamax) of 0.2-0.5 MPa were observed for coatings produced from pure calcium carbonate or calcium carbonate-latex suspensions, whereas coatings with carboxymethylcellulose exhibited substantially higher sigmamax values of 1-2 MPa. Upon drying, these coatings were quite hygroscopic, such that cyclic variations in relative humidity induced large cyclic changes in residual stress.     

On the two isomeric tris(perchlorothienyl)methyl radicals

The two isomeric tris(trichlorothienyl)carbinols have been synthesized. Upon treatment with acid the tris(trichlorothienyl)carbenium ions were formed, which upon reduction with iodide gave the tris(trichlorothienyl)methyl radicals, which were studied by epr-spectroscopy. The β-isomer, the tris(2,4,5-trichloro-3-thienyl)methyl radical, was much more stable than the α-isomer and showed great similarity to the perchlorotrityl radical.     

Particle-induced phase separation in mixed polymer solutions

The influence of added colloidal particles on the phase separation of mixed aqueous polymer solutions is investigated. Two types of particles (polystyrene latex or silica) and different combinations of segregating polymers (dextran of varying molar mass combined with poly(ethylene oxide) (PEO) of varying molar mass, or Ucon, a copolymer of ethylene oxide and propylene oxide) were used. All systems displayed particle-induced instability effects, but the extent of the effect varied strongly between the various combinations and with the amount of added salt. Very large instability effects were seen in certain mixtures. Two mechanisms, both relying on the adsorption of at least one of the polymers to the particle surface, seem to operate. Close to the cloud-point curve of the particle-free polymer1/polymer2/water mixture, adsorption of PEO or Ucon to the particles gives rise to a capillary-induced phase separation. Close to the dextran/water axis of the phase diagram, the adsorbing polymer gives rise to a surface modification of the particles, which then interacts repulsively with the surrounding dextran solution.     

Membrane-based techniques for sample enrichment

Sample preparation techniques based on non-porous membrane extraction generally offer a high degree of selectivity and enrichment power, together with convenient possibilities for direct and automated connections to chromatographic and other analytical instruments. In this review principles and applications for techniques as supported liquid membrane extraction, microporous membrane liquid-liquid extraction, polymeric membrane extraction and membrane extraction with a sorbent interface are described and compared.     

Gels of hydrophobically modified ethyl(hydroxyethyl) cellulose cross-linked by amylose: effects of hydrophobe architecture

Previous work has shown that amylose (AM) can cross-link hydrophobically modified polymers by inclusion complexation, whereby thermoreversible cold-setting gels are formed. Here we investigate the complexation of AM with different samples of hydrophobically modified ethyl(hydroxyethyl) cellulose (HMEHEC), distinguished by differences in the architecture of the hydrophobes (the hydrophobic side chains). All hydrophobes, except one, were based on linear alkyl chains, but with varying chain lengths (C12-C14). In addition, some samples contained short hydrophilic "spacers", consisting of 2-5 ethylene oxide units, between the alkyl chains and the EHEC backbone. Gels of varying strength were obtained for the different AM/HMEHEC samples. The alkyl chain length seemed to be the major factor affecting the gel strength, with longer alkyl chains giving stronger gels. For similar alkyl chain lengths, stronger gels were obtained when a spacer was present. Addition of AM caused a small increase of the cloud points of HMEHECs with C14 hydrophobes in water. Time-dependent effects and effects of the sample preparation procedure were also investigated. The reversibility of the gelation with respect to shear was confirmed. A gel destroyed by added surfactant was shown to reform on removal of the surfactant by dialysis.     

Syntheses and spectroscopic properties of energy transfer systems based on squaraines

The purpose of this project was to prepare fluorescent dyes that could absorb energy at relatively short wavelengths, and fluoresce in the near-IR region. To achieve this, copper- and palladium-mediated C-N couplings were used to prepare the ‘cassettes’, i.e the carbazole derivative 3b and the carbazole-, phenothiazine-, and phenoazine-squaraines 4b-d. These compounds have carbazole, phenothiazine, and phenoazine donor-components that absorb around about 300-320 nm, and squaraine acceptor-parts that fluoresce in the range 650-700 nm. The efficiencies of energy transfer from the donor to the acceptor, and the overall quantum yields of the cassettes were determined.