A new approach for fluorine determination by solid sampling graphite furnace molecular absorption spectrometry

This work deals with the determination of fluorine by solid sampling graphite furnace molecular absorption spectrometry. The molecular absorbance of aluminum monofluoride (AlF), which is produced in the vapor phase in the presence of Al³⁺, is measured at 227.5 nm, a non-resonant platinum line. A conventional graphite furnace program has been used with pyrolysis and vaporization temperatures of 800 and 2300 °C, respectively. Solutions of Ba²⁺ and Al³⁺ have been used to avoid fluorine losses during the pyrolysis stage and to produce AlF in the vaporization stage, respectively. Certified coal and alumina samples were analyzed using aqueous standards for calibration. The agreement between the found concentration and the certified value, or the value obtained by another method ranged from 92 to 105%, with a relative standard deviation less than 8.5%. The limit of detection and the characteristic mass was 0.17 μg g^− 1 and 205 pg, respectively.     

Fluorescence-quenched solid phase combinatorial libraries in the characterization of cysteine protease substrate specificity

To map the substrate specificity of cysteine proteases, two combinatorial peptide libraries were synthesized and screened using the archetypal protease, papain. The use of PEGA resin as the solid support for library synthesis facilitated the application of an on-resin fluorescence-quenched assay. Results from the screening of library 2 indicated a preference for Pro or Val in the S3 subsite and hydrophobic residues in S2; the most prevalent residue not being Phe but Val. The S1 subsite exhibited a dual specificity for both small, nonpolar residues, Ala or Gly, as well as larger, Gln, and charged residues, Arg. Small residues predominated in the S1'-S4' subsites. Active peptides from the libraries and variations thereof were resynthesized and their kinetics of hydrolysis by papain assessed in solution phase assays. Generally, there was a good correlation between the extent of substrate cleavage on solid phase and the kcat/KM's obtained in solution phase assays. Several good substrates for papain were obtained, the best substrates being Y(NO2)PMPPLCTSMK(Abz) (kcat/KM = 2109 (mM s)-1), Y(NO2)PYAVQSPQK(Abz) (kcat/KM = 1524 (mM s)-1), and Y(NO2)PVLRQQRSK(Abz) (kcat/KM = 1450 (mM s)-1). These results were interpreted in structural terms by the use of molecular dynamics (MD). These MD calculations indicated two different modes for the binding of substrates in the narrow enzyme cleft.     

Synergic effect in electrical conductivity using a combination of two fillers in PVDF hybrids composites

The objective of this work was to prepare novel conductive blends of poly(vinylidene fluoride) (PVDF) with polypyrrole (PPy) and to compare their performance with PVDF/multiwall carbon nanotube (MWCNT) composites and novel PVDF/PPy/MWCNT hybrid systems. All the compositions were prepared by melt mixing using a miniature mixer. The mixtures were characterized by Fourier transformed infrared (FTIR), wide angle X-ray diffraction (WAXD), thermogravimetric analyses (TGA), scanning and transmission electron microscopy (SEM and TEM, respectively) and volume electrical resistivity. For the binary PVDF/PPy and PVDF/MWCNT systems, percolation thresholds of 10 and 0.3 wt%, respectively, were found. In the hybrid systems, however, the percolation threshold for each filler was lower than in the binary systems, but the electrical conductivities were always much higher at all concentrations than the conductivities of the binary systems. Therefore, the addition of both fillers had a synergistic effect on the hybrid system conductivity, which was attributed to its morphology: the PPy increased the homogeneity of the MWCNT distribution and decreased the available free volume for the MWCNT; as a result the MWCNT rolled around the PPy particles bridging them through the PVDF matrix, increasing the quantum tunneling effect and thus, the electrical conductivity of the system.     

Physico-chemical and anatomical characterization of residual lignocellulosic fibers

Anatomical and physico-chemical properties of residual natural fibers (sugarcane bagasse, coconut fibers and peanut hulls) were characterized in order to evaluate their potential for use in the production of particleboard. The bulk density was determined by helium pycnometer and the chemical characteristics by using an electronic pH meter (for pH determination) on fibers dissolved in acidic and neutral detergents (to determine the levels of cellulose, hemicellulose and lignin). The anatomical characteristics were established using scanning electron microscopy coupled with an X-ray detector system, as well as energy dispersive X-ray spectroscopy. Results indicated similarities and differences between physico-chemical and anatomical characteristics of the residual lignocellulosic fibers when compared with the Pinus sp. wood commercially employed in particleboard production. Bulk density and pH for residual lignocellulosic fibers and Pinus sp. wood presented analogous values. Similar amounts of cellulose and lignin were identified between waste fibers and Pinus sp. wood. The presence of silica was identified in coconut fiber, peanut hull and sugarcane bagasse waste fibers, and may affect the mechanical characteristics of panels. Coconut and sugarcane bagasse fibers show surface pores with diameters ranging from 1.2 to 2.1 μm, below the 5 μm identified for Pinus sp. wood. Both fibers present pores distributed over their entire surface, whereas peanut hull fibers have no pores on their surface. This characteristic contributes to resin dispersion among particles, reflecting positively on the physical–mechanical properties of the panels. Particleboards produced with residual lignocellulosic fibers present similar physical–mechanical properties to those of Pinus sp. wood panels.     

Copper salt-catalyzed homo-coupling reaction of potassium alkynyltrifluoroborates: a simple and efficient synthesis of symmetrical 1,3-diynes

The copper-catalyzed dimerization of alkynyltrifluoroborates proceeds readily with good yields. The homo-coupling reaction can be effected in DMSO, in the open air, using Cu(OAc)₂ as catalyst in the absence of any other additives. A variety of functional groups are tolerated.     

Metastable flow in capillary tubes: An experimental evaluation

This work presents the results of an experimental study with pure refrigerants R-134a and R-600a and refrigerant–oil mixtures flowing through capillary tubes in order to analyse the metastable flow. A large number of experiments were carried out to verify the influence of several variables on the underpressure of vaporization, mainly the inlet subcooling, internal diameter and inlet pressure. Capillary tubes with internal diameter of 0.69 mm and 0.82 mm were tested for condensation temperatures between 40 °C and 50 °C and subcooling degrees between 3 °C and 12 °C. Measurements for oil concentrations of 1% and 3% were conducted and compared with those for pure refrigerant R-134a. The oil influence on the metastable flow was tested and the effect on the underpressure of vaporization is addressed for lower oil concentrations.     

Enhanced creaming of milk fat globules in milk emulsions by the application of ultrasound and detection by means of optical methods

The effects of application of ultrasonic waves to recombined milk emulsions (3.5% fat, 7% total solids) and raw milk on fat destabilization and creaming were examined. Coarse and fine recombined emulsions (D[4,3]=9.3 μm and 2.7 μm, respectively) and raw milk (D[4,3]=4.9 μm) were subjected to ultrasound for 5 min at 35°C and 400 kHz or 1.6 MHz (using a single transducer) or 400 kHz (where the emulsion was sandwiched between two transducers). Creaming, as calculated from Turbiscan measurements, was more evident in the coarse recombined emulsion and raw milk compared to that of the recombined fine emulsion. Micrographs confirmed that there was flocculation and coalescence in creamed layer of emulsion. Coalescence was confirmed by particle size measurement. These results imply that ultrasound has potential to pre-dispose fat particles in milk emulsions to creaming in standing wave systems and in systems with inhomogeneous sound distributions.     

Effect of grinding method on the analysis of essential oil from <Emphasis Type="Italic">Baccharis articulata</Emphasis> (Lam.) Pers.

Grinding methods were evaluated aiming to determine yield and composition of essential oils (EOs) from Baccharis articulata (Lam) Pers., called as carqueja, a native plant from South Brazil. Cryogenic, knife (with and without cooling) and ball mills were used. The major constituents found in EOs were β-pinene, caryophyllene, spathulenol and caryophyllene oxide, but differences in 21 compounds were observed. All grinding processes reduced monoterpenes and oxygenated sesquiterpenes with concentration of hydrocarbon sesquiterpenes. The sesquiterpenes (hydrocarbons and oxygenated) were found from 63.55 to 86.02% while the monoterpene hydrocarbons’ concentration ranged from 13.98 to 36.45%. Plants milled with knife mill provided EOs with profile similar to those not grinded. Despite the lower working temperature, cryogenic milling resulted in smaller EO yield (0.40 ± 0.03%) in comparison to other grinding methods (yields from 0.50 ± 0.02 to 0.56 ± 0.03%) and different chromatographic profile. Microscopic analysis showed the smaller particle size provided by cryogenic grinding, which leads to glandular trichome rupture and consequently to loss of EOs. This study showed that grinding should be carefully evaluated to provide reproducible results in essential oil analysis.     

Oxaliplatin preformulation studies for the development of innovative topical drug delivery systems

Journal of Thermal Analysis and Calorimetry - The objectives of this study were to verify the viability of the photoinitiating system using curcumin as a photoinitiator and glycerol as a...