Physical properties of glycosaminoglycan hydrogels

The chemical composition of glycosaminoglycan (GAG) hydrogels was found to have a profound effect on the physical properties of gels. Hyaluronan (HA) and chondroitin sulfate (CS) were each modified with adipic dihydrazide (ADH) with carbodiimide chemistry. The resulting polymer was crosslinked with various concentrations of poly(ethylene glycol) dialdehyde (PEG‐diald) to produce a series of hydrogels. The physical properties of these GAG hydrogels varied in a concentration‐dependent fashion. Maximal crosslinking was observed at a theoretical crosslinking of 50% for the HA‐ADH‐PEG‐diald hydrogels and 75% for the CS‐ADH‐PEG‐diald hydrogels. Adding PEG‐diald beyond the optimum for crosslinking prolonged the in vitro enzymatic degradation time of the hydrogels. The swelling of the crosslinked GAG hydrogels was correlated with the amount of PEG‐diald used rather than with the crosslinking density. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 4344–4356, 2004     

Mode beating in spot-size converter lasers

An anomalous modulation in the wavelength spectrum has been observed in lasers with spot-size converters. This intensity modulation is shown to be caused by beating between the fundamental lasing mode and radiation modes in the taper. This results in a periodic modulation in the net gain spectrum, which causes wavelength jumps between adjacent net gain maxima, and a drive current dependent spectral width that is expected to affect system performance. The amplitude of this spectral modulation is reduced significantly by either using an angled rear-facet which reflects the beating radiation modes away from the laser axis, or by using a nonlinear, adiabatic taper.     

Another independent self-dual basis for the trivial variety

We give a new independent self-dual 3-basis for the trivial variety with two binary operations. Received October 24, 2006; accepted in final form January 25, 2007.     

Mode-locking dynamics of a laser coupled to an empty external cavity

The effect of incorporating an empty external cavity into the feedback loop of a mode-locked laser is investigated. Particular attention is paid to the response of the mode-locking as the external cavity is detuned by a fraction of a wavelength from the round trip transit time associated with the laser. The results for two regimes of operation are presented. In the first case a series of short lived transients develop whereas the other case leads to a persistent intermittent Q-switching scenario, where mode-locking fails. The role of coupling between the cavities and the laser's memory time in relation to the results is discussed. A mechanism for the improved mode-locking observed with non-linear external cavities is suggested.     

An anisotropic fibre-network model for mechano-sorptive creep in paper

In this paper a simplified network model for mechano-sorptive creep is presented, which is a further development of an earlier paper [Strömbro, J., Gudmundson, P., 2008. Mechano-sorptive creep under compressive loading – a micromechanical model. International Journal of Solids and Structures 45 (9), 2420–2450.]. It is assumed that the anisotropic hygroexpansion of the fibres leads to large stresses at the fibre bonds when the moisture content changes. The resulting stress state will accelerate creep if the fibre material obeys a constitutive law that is non-linear. Fibre kinks are included in order to capture experimental observations of larger mechano-sorptive effects in compression than in tension. Moisture dependent material parameters and anisotropy in the fibre distribution have been introduced. Theoretical predictions based on the model are compared to experimental results for an anisotropic paper both under tensile and compressive loading at varying moisture content and it is found that the important features in the experiments are captured by the model. Different kinds of drying conditions have also been examined.     

Structure and catalytic activity of some soluble polyethylene glycol-peptide conjugates

Soluble catalysts for the Juliá-Colonna asymmetric epoxidation reaction have been constructed in three different ways, using NH₂-PEG-OMe as the support system: suitable solvents have been identified and it is shown that the degree of helicity of the conjugates correlates with the extent of conversion and (to a lesser extent) the enantioselectivity of epoxidation.     

Four unit linking groups IV. Liquid crystals of positive dielectric anisotropy

Three separate series of new materials of weak to strongly positive dielectric anisotropy have been prepared. Each series contains four sub-sets of materials each incorporating a different four unit linking group (i.e., C₄H₈, C₄H₆, C₃H₆O and C₃H₄O) and the same series of end groups (i.e. F, CN and OCF₃) in various substitution patterns. The synthesis and liquid crystal transition temperatures of these novel substances are described and compared with those of the corresponding materials incorporating standard central linkages (i.e.-, C₂H₄, CH₂O, COO). The effect of an additional trans carbon-carbon double bond in the terminal alkyl chain and in the central linking unit has also been studied.     

Effect of stoichiometry on liquid crystalline supramolecular polymers formed with complementary nucleobase pair interactions

We report herein studies on the liquid crystalline behavior of a series of supramolecular materials that contain different ratios of two complementary symmetrically-substituted alkoxy-bis(phenylethynyl)benzene AA- and BB-type monomers. One monomer has thymine units placed at either end of the rigid mesogenic core, while the other has N⁶-(4-methoxybenzoyl)-adenine units placed on the ends. Differential scanning calorimetric and polarized optical microscopy studies have been carried out on these systems. These studies show that the material's behavior is strongly dependent on its thermal history. As a result, the materials can exhibit, on heating, either a liquid crystalline phase, a crystalline phase, or the coexistence of crystalline and liquid crystalline regions. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5049–5059, 2006     

Behaviour and design considerations for continuous flow closed-open-closed liquid microchannels

This paper introduces a method of combining open and closed microchannels in a single component in a novel way which couples the benefits of both open and closed microfluidic systems and introduces interesting on-chip microfluidic behaviour. Fluid behaviour in such a component, based on continuous pressure driven flow and surface tension, is discussed in terms of cross sectional flow behaviour, robustness, flow-pressure performance, and its application to microfluidic interfacing. The closed-open-closed microchannel possesses the versatility of upstream and downstream closed microfluidics along with open fluidic direct access. The device has the advantage of eliminating gas bubbles present upstream when these enter the open channel section. The unique behaviour of this device opens the door to applications including direct liquid sample interfacing without the need for additional and bulky sample tubing.