Investigation of mass attenuation coefficients of water, concrete and bakelite at different energies using the FLUKA Monte Carlo code

The mass attenuation coefficients of water, bakelite and concrete sample defined in the simulation package were obtained using the FLUKA Monte Carlo code at 59.5, 80.9, 140.5, 356.5, 661.6, 1173.2 and 1332.5 keV photon energies. The results for the mass attenuation coefficients obtained by simulation have been compared with experimental and the theoretical ones and good agreement has been observed. The results indicate that this process can be followed to determine the data on the attenuation of gamma-rays with the several energies in other materials. Also, the deposited energy by 661.6 keV photons at several thicknesses of each media was determined as being an important data for radiation shielding studies.     

Effects of solvent on TEOS hydrolysis kinetics and silica particle size under basic conditions

In-situ liquid-state ²⁹Si nuclear magnetic resonance was used to investigate the temporal concentration changes during ammonia-catalyzed initial hydrolysis of tetraethyl orthosilicate in different solvents (methanol, ethanol, n-propanol, iso-propanol and n-butanol). Dynamic light scattering was employed to monitor simultaneous changes in the average diameter of silica particles and atomic force microscopy was used to image the particles within this time frame. Solvent effects on initial hydrolysis kinetics, size and polydispersity of silica particles were discussed in terms of polarity and hydrogen-bonding characteristics of the solvents. Initial hydrolysis rate and average particle size increased with molecular weight of the primary alcohols. In comparison, lower hydrolysis rate and larger particle size were obtained in the secondary alcohol. Exceptionally, reactions in methanol exhibited the highest hydrolysis rate and the smallest particle size. Ultimately, our investigation elaborated, and hence confirmed, the influences of chemical structure and nature of the solvent on the formation and growth of the silica particles under applied conditions.     

ChemInform Abstract: Structure,Ionization, and Fragmentation of Hydrogenated Aluminoboron Clusters: Al2B2H2n (n = 0—6).

Energetic and structural stability of Al₂B₂H_2n (n = 0—6) clusters is investigated by DFT calculations and a stochastic search algorithm.     

Time‐dependent morphology development in segmented polyetherurea copolymers based on aromatic diisocyanates

Time‐dependent morphology development in segmented polyureas obtained by the stoichiometric reactions between amine terminated poly(tetramethylene oxide) (PTMO) and aromatic diisocyanates were investigated. Polyureas were prepared by reacting aminopropyl terminated PTMO oligomer (M_n = 1100 g/mol) and various aromatic diisocyanates, such as 1,4‐phenylene diisocyanate (PPDI), 1,3‐phenylene diisocyanate (MPDI), diphenylmethane diisocyanate (MDI), and tolylene diisocyanate (TDI). Time‐dependent FTIR studies were conducted on thin films cast onto KBr discs, which were annealed at 200 °C for 10 min in an air oven. After removing from the oven, samples were placed into the FTIR spectrometer at room temperature, where time‐dependent spectra were recorded until equilibrium was reached. Time‐dependent peak reorganization in 3500–3100 cm^?1 (N? H region), 1750–1450 cm^?1 (C?O region or amide I and amide II regions), and 1180–1020 cm^?1 (C? O? C) were monitored. Depending on the chemical structure and the symmetry of the diisocyanate, major differences were observed in the time needed to reach an equilibrium morphology in these homologous poly(ether urea) copolymers. Symmetric PPDI‐based polyurea reached equilibrium in about 1 h compared with its asymmetric MPDI‐based counterpart, which needed about 150 h. Microphase development of the MPDI urea was also characterized by AFM, which gave similar results. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 471–483, 2009     

Structural response of different Lewis number premixed flames interacting with a toroidal vortex

Simultaneous measurements of temperature, CH* and OH* chemiluminescent species are carried out to explore the impact of stretch rate and curvature on the structure of premixed flames. The configuration of an initially flat premixed flame interacting with a toroidal vortex is selected for the present study and reasons for this choice are discussed. Lewis number effects are assessed by comparing methane and propane flames. It is emphasized that the flame structure experiences very strong variations. In particular, the flame is shrunk (broadened) in the initial (final) period of the interaction with the vortex where strain rate (curvature) contribution of the stretch rate is predominant. By further analysing independently the thickness of the preheat and reaction zones, it is shown that for propane flames, not only the former but also the latter is significantly altered in zones where the flame curvature is negative. Changes in the reaction zone properties are further emphasized using CH* and OH* radicals. It is demonstrated that higher thermal diffusivity plays a significant role around curved regions, in which the enhanced diffusion of heat leads to a strong increase of CH* compared to OH* intensity. As an overall conclusion, this study suggests that it would be interesting to reassess the internal flame structure at lower and moderate Karlovitz numbers since changes might appear for a moderate vortex intensity with typical size much larger than the flame thickness.     

Thermochemistry of methyl and ethyl esters from vegetable oils

This paper deals with the gas‐phase thermodynamic properties of methyl ester and ethyl ester of vegetable oils (fatty acid methyl esters and fatty acid ethyl esters respectively) present in biodiesel. The standard enthalpies of formation at 298.15 K, heat capacities, and entropies in the temperature range 300–5000 K are determined by means of quantum chemistry calculations along with a protocol developed for these compounds. The resultant data, currently not available in the literature for most of them, are critical to the modeling of combustion chemistry of the subject compounds. © 2007 Wiley Periodicals, Inc. Int J Chem Kinet 39: 481–491, 2007     

Effect of Symmetry and H‐bond Strength of Hard Segments on the Structure‐Property Relationships of Segmented,Nonchain Extended Polyurethanes and Polyureas

Segmented, nonchain extended polyurethanes and polyureas based on PTMO soft segments (SS) and hard segments (HSs) based on only single molecules of a diisocyanate were synthesized. Type and nature of the diisocyanate was systematically varied in order to analyze the effect of HS symmetry and type of linkage between the HS and SS on the structure‐property relationship of these segmented copolymers. Results showed that the increased symmetry of the diisocyanates allows a more efficient packing of the HSs which leads to a microphase‐separated structure with the crystalline hard ribbon or thread‐like domains percolated throughout the SS matrix, even with a low HS content (ca. 13 wt.%). The service window of these segmented copolymers was significantly influenced by the symmetry and type of linkage between the HS and SS. Most copolymers also showed evidence of strain hardening accented by the strain induced crystallization of the PTMO SS.     

Relativistic energies of 1s2, 1s22s and 1s22s2 isoelectronic sequences in first- and second-row atoms

An accurate semi-empirical method based on the many-electron theory of Sinano?lu for calculating relativistic contributions to atomic energies is developed and applied to the 1s², 1s²2s and 1s²2s² isometric sequences in the first and second periods. Orbital additivity of relativistic energies is tested and found to be an inaccurate assumption for small Z.     

Novel triblock siloxane copolymers: Synthesis,characterization, and their use as surface modifying additives

Synthesis of novel triblock, polycaprolactone-b-polydimethylsiloxane (PDMS) and poly(2-ethyl-oxazoline)-b-PDMS copolymers were demonstrated. These materials were obtained via the ring-opening polymerization of ?-caprolactone or 2-ethyl-2-oxazoline monomers by using organofunctionally terminated PDMS oligomers as initiators and comonomers. Segment molecular weights in these copolymers were varied over a wide range between 1000 and 2000 g/mol and the formation of copolymers with desired backbone compositions were monitored by ¹H-NMR spectroscopy and GPC. DSC and TMA studies showed the formation of two phase morphologies with PDMS (T_g, ?120°C) and polycaprolactone (T_m, 50–60°C) or poly(2-ethyl-2-oxazoline) (T_g, 40-60°C) transitions respectively. The use of polycaprolactone-b-PDMS copolymers as surface modifying additives in polymer blends were also investigated. When these copolymers were blended at low levels (0.25–10.0% by weight) with various commercial resins such as, polyurethanes, PVC, PMMA, and PET, the resulting systems displayed silicone-like, hydrophobic surface properties, as determined by critical surface tension measurements or water contact angles. The effect of siloxane content, block length, base polymer type and morphology on the resulting surfaces are discussed.     

PIB‐based polyurethanes. IV. The morphology of polyurethanes containing soft co‐segments*

Novel polyurethanes consisting of polyisobutylene (PIB)/poly(tetramethylene oxide) (PTMO) or PIB/poly(hexamethylene carbonate) (PC) soft co‐segments in combination with 4,4′‐methylene‐bis(cyclohexyl isocyanate)/1,6‐hexanediol, 1,4‐butanediol, or 1,6‐hexamethylene diamine hard segments exhibit excellent mechanical properties (upto 31 MPa tensile strength with 700% elongation) together with unprecedented oxidative/hydrolytic stability. A structural model of the morphology of these polyurethanes was developed that reflects this combination of properties. The key new elements of our model are H bridges between the PTMO and PC type soft and urethane hard segments, which compatibilize the soft and hard domains, and the presence of large quantities of chemically resistant PIB soft segments that protect the other oxidatively/hydrolytically vulnerable constituents. A variety of FTIR, DSC, SAXS, AFM, and DMTA experiments strongly support the proposed morphological model. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 6180–6190, 2009