Room-Temperature,Metal-Free,and One-Pot Preparation of 2H-Indazoles through a Mills Reaction and Cyclization Sequence

The Mills reaction and cyclization of readily available 2-aminobenzyl alcohols and nitrosobenzenes using thionyl bromide provided 2H-indazoles in up to 88 % yields. In the metal-free process, acetic acid played a crucial role for the both Mills reaction and cyclization. A brominated 2H-indazole could also be obtained through the one-pot sequence.     

Unsteady and chaotic characteristics of natural convection field in vertical slots at large Prandtl number

In this study we examined the unsteady and chaotic characteristics of the natural convection field in vertical slots at large Prandtl number. In the computation, temperature dependence of viscosity was partially taken into consideration. As a result we discovered that the spatial region where a significant temperature fluctuation is detected corresponds to the spatial region where the secondary cells exist. The largest Lyapunov exponents calculated from the temperature on the center line have a local maximum at the lower region of the enclosure when the viscosity change was considered. These characteristics agree well with the experimental ones that have been observed by authors (Ishida, Kure and Kimoto 2001).     

Study on crystalline properties of Er-Si-O compounds in relation to Er-related 1.54 μm photoluminescence and electrical properties

Er-Si-O crystalline compounds, which exhibit superlattice structures and sharp and strong Er-related 1.54 μm photoluminescence (PL) spectra at room temperature have been formed by self-assembling growth mechanism. Oxidation of the starting materials which have Si and Er at an atomic ratio of 2:1 are prepared and then oxidation and succeeding high-temperature annealing in Ar above 1250 °C cause a self-assembled superlattice-structured Er-Si-O crystalline compounds. The control of the ratio of Si and Er, as well as the following oxidation and annealing processes, is found to be sensitive to the crystalline properties, PL spectra and electrical properties. In this study, Er-Si-O crystalline thin films are formed on Si substrates by sol-gel and MOMBE methods, and their crystalline properties such as crystalline orientation and concentration ratio of Er, Si and O are investigated. Crystalline Er-Si-O films of high orientation are successfully grown on Si(1 0 0) and its inclined surface. The PL and excitation spectra, fluorescence decay and the electrical properties are found to be strongly related to the crystalline properties. Excess O causes a broader 1.54 μm PL spectra, slower fluorescence decay, lower carrier-mediated excitation and higher resistivity. A precise control of O is found to be necessary to grow superlattice-structured Er-Si-O compounds, which are semiconducting and are excitable via carrier-mediated excitation mechanism.     

Light Diffraction of Aligned Polymer Fibers Periodically Dispersed by Phase Separation of Liquid Crystal and Polymer

We have confirmed light diffraction of aligned polymer fibers obtained by a phase separation of an anisotropic-phase solution of liquid crystal and polymer. He—Ne laser light passing through the polymer fibers was scattered in the axis vertical to the fibers, and had two peaks of light intensity symmetrical to the center of the transmitting laser spot. The two peaks were found to be caused by light diffraction due to the periodic polymer-fiber dispersion because the peaks corresponded to values calculated by intervals between the fibers. The periodical fiber networks are considered to be formed by anisotropic spinodal decomposition. This effect can be used to measure the dispersion order of the polymer fibers. © 2004 The Optical Society of Japan     

Ultrahigh‐molecular‐weight‐polyethylene‐fiber surface treatment by electron‐beam‐irradiation‐induced graft polymerization and its effect on adhesion in a styrene–butadiene rubber matrix

Aiming to develop a high‐performance fiber‐reinforced rubber from styrene–butadiene rubber (SBR), we applied a special technique using electron‐beam (EB)‐irradiation‐induced graft polymerization to ultrahigh‐molecular‐weight‐polyethylene (UHMWPE) fibers. The molecular interaction between the grafted UHMWPE fibers and an SBR matrix was studied through the evaluation of the adhesive behavior of the fibers in the SBR matrix. Although UHMWPE was chemically inert, two monomers, styrene and N‐vinyl formamide (NVF), were examined for graft polymerization onto the UHMWPE fiber surface. Styrene was not effective, but NVF was graft‐polymerized onto the UHMWPE fibers with this special method. A methanol/water mixture and dioxane were used as solvents for NVF, and the effects of the solvents on the grafting percentage of NVF were also examined. The methanol/water mixture was more effective. A grafting percentage of 16.4% was the highest obtained. This improved the adhesive force threefold with respect to that of untreated UHMWPE fibers. These results demonstrated that EB irradiation enabled graft polymerization to occur even on the inert surface of UHMWPE fibers. However, the mechanical properties of the fibers could be compromised according to the dose of EB irradiation. © 2004 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 42: 2595–2603, 2004     

Improved detectability with a polymer-based trapping device in rapid HPLC analysis for ultra-low levels of bisphenol A (BPA) in environmental samples.

A new high-performance liquid chromatography (HPLC) method has been developed to detect ultra-low concentrations of bisphenol-A (BPA) (below 1 ng/L (ppt)) using column switching electrochemical detection (ECD). The results were superior to those obtained from manual pretreatment procedure with membrane stationary phase. BPA is inherently ubiquitous in the environment, including tools and solvents used for its analysis; to obtain meaningful results, therefore, the concentration of the overall BPA contamination must be below the detection limit for BPA using the analytical system. Therefore, purified water for preparing the standard BPA solution must be filtered with a hydrophobic membrane to suppress BPA background levels of contamination. In addition, we investigated methods for effectively preserving environmental water containing BPA. The addition of a small amount of ethylenediaminetetraacetic acid (EDTA) provided good recovery even after overnight storage. By employing these precautionary measures and procedures to reduce BPA contamination from the analytical procedure, we could accurately determine l(-10) ppt of BPA in environmental water samples using a column switching HPLC system.     

Linear and Nonlinear Optical Properties Of Racemic (±)2-(α-Methylbenzylamino)-5-Nitropyridine Single Crystals

Linear and nonlinear optical properties of racemic (±)2-(α-methylbenzylamino)-5-nitropyridine ((±)MBANP) single crystals have been comprehensively investigated and compared with those of the enantiomorph (–)2-(α-methylbenzylamino)-5-nitropyridine ((–)MBANP) crystals. (±)MBANP crystal exhibits very high chemical and physical stability, but relatively small nonlinear optical coefficients (d₃₁ = 6.8 pm/V, d₃₂ = 4.7 pm/V, d₃₃ = 0.84 pm/V). A comparison between the nonlinear optical coefficients of (±)MBANP and (–)MBANP demonstrates the validity of the oriented-gas model in molecular crystals that neglects all the contributions from intermolecular interaction.     

In situ observations of domain wall motion in Mn–Zn and Ni–Zn ferrites by Lorentz microscopy and electron holography

Domain wall motion in Mn–Zn and Ni–Zn ferrites with applied magnetic fields is investigated by in situ observations with Lorentz microscopy and electron holography. It is found that both Mn–Zn and Ni–Zn ferrites have a mean grain size of approximately 10 μm and several pores with sizes ranging from 0.2 to 1.1 μm. In situ observations by Lorentz microscopy with an applied magnetic field reveals that in Mn–Zn ferrite, the domain walls move easily across the grain boundary, while in Ni–Zn ferrite, the domain walls move along the grain boundary but are pinned at the grain boundary and pores. From in situ observations of Ni–Zn ferrite by electron holography, it is clarified that domain wall pinning at the grain boundary retards a sensitive increase in magnetic flux parallel to the applied field direction, which is considered to result in high hysteresis loss.     

Curved Ferroelectric Liquid Crystal Matrix Displays Driven by Field-Sequential-Color and Active-Matrix Techniques

This paper describes a curved field-sequential-color matrix display using fast-response ferroelectric liquid crystal. Black matrix and transparent electrode patterns were formed on a thin plastic substrate by a transfer method from a glass substrate. While a composite film of liquid crystal and micro-polymers of walls and fibers was formed between the flexible substrates by printing, laminating and curing processes of a solution of monomers and liquid crystal, the mechanical stability was enhanced by use of multi-functional monomers to form large display panels. The image pixels of the matrix panel were driven by an active matrix scheme using an external switch transistor array at a frequency of 180 Hz for intermittent three-primary-color backlight illumination. The flexible A4-paper-sized color display with 24 × 16 pixels and 60 Hz field frequency was demonstrated by illuminating it with sequential three-primary-color lights from light-emitting diodes of the backlight. Our display system is useful in various information displays because of its freedom of setting and location.