Constructing a new optical sensor for monitoring ammonia in water samples using bis(acetylacetoneethylendiamine)-tributylphosphin cobalt(III) tetraphenylborate complex-coated triacetylcellulose.

A new ammonia optical sensor was designed using bis(acetylacetoneethylendiamine)tributylphosphin cobalt(III) tetraphenylborate complex, coated on transparent triacetylcellulose film as membrane. The change in the absorbance of the optode at the maximum wavelength of 408 nm was related to ammonia concentration in aqueous samples. A buffer solution with a pH of 9 (sodium borate-HCl) was used. The optode was fully regenerated in pH 2. The linear dynamic range for determination of ammonia was 3.3 x 10(-4) to 6.9 x 10(-3) mol l(-1) with a detection limit of 5.0 x 10(-5) mol l(-1) and a response time range of 4 - 6 min. This membrane was successfully applied for determination of ammonia in drinking water.     

Application of 2‐(benzyliminomethyl)‐6‐methoxy‐4‐(4‐methoxyphenyl‐azo)phenol in construction of ion‐selective PVC membrane electrode for determination of copper (II) in mineral water sample

The potentiometric characteristics of a new Cu²⁺‐selective electrode based on 2‐(benzyliminomethyl)‐6‐methoxy‐4‐(4‐methoxyphenyl‐azo) phenol as an efficient ionophore has been evaluated. The effects of influential parameters on the potentiometric responses such as the amount of plasticizer, the amount of ionophore, pH of the sample solution, and the effect of coexisting ions on the electrode signal were subsequently investigated . The selectivity of the electrode was assessed by calculating the selectivity coefficients using the matched potential method. The optimum ratio of the amount of materials required for the preparation of the electrode was found to be 1.7: 32.1: 64.2: 2.0 corresponding to carboxylated PVC, dimethyl sebacate as solvent mediators, potassium tetrakis (p‐chlorophenyl) borate as the anion localizing agent, and ionophore, respectively. The electrode had a fast response (7s) as well as a satisfactory Nernstian slope (29.26±0.91 mV/decade) to Cu²⁺ over a wide concentration range of 2.0×10^?6‐ 5.0×10^?2 M with a low detection limit of 5.9×10^?7 M. The developed sensor was successfully used for the potentiometric titration of Cu²⁺ ion with EDTA and subsequently, efficient determination of this metal ion in a mineral water sample was performed.     

Fast removal and determination of doxycycline in water samples and honey by Fe<Subscript>3</Subscript>O<Subscript>4</Subscript> magnetic nanoparticles

Adsorption characteristics and doxycycline (DC) removal efficiency of Fe₃O₄ magnetic nanoparticles as adsorbents have been determined by investigating the effects of pH, concentration of the DC, amount of adsorbents, contact time, ionic strength and temperature. The mechanism of adsorption was also studied. The adsorption of DC to the Fe₃O₄ magnetic nanoparticles could be described by Langmuir-type adsorption isotherms. Short contact time between the reagents, reusability of Fe₃O₄ for three times after recycling of the nanoparticles, good precision and accuracy, wide working pH range and high breakthrough volume are among the highlights of this procedure. The proposed extraction and determination procedure based on magnetic nanoparticles as adsorbent was successfully applied to the determination of DC spiked in honey and various water samples. The method presented here is fast, simple, cheap and robust, and it does not require the use of organic solvents. Also, the method needs only a magnet and can be performed in any laboratory without sophisticated equipment.     

Study on the adsorption of DNA on Fe3O4 nanoparticles and on ionic liquid-modified Fe3O4 nanoparticles

We have investigated the adsorption of herring sperm DNA on Fe₃O₄ magnetic nanoparticles (NPs) before and after modification with the ionic liquid 1-hexyl-3-methylimidazolium bromide. Experiments were performed in a batch mode, and the effects of DNA concentration, pH of the sample solution, ionic strength, temperature, and contact time between reagents were optimized. An evaluation of the adsorption isotherm revealed that the Langmuir model better fits the equilibrium data than the Freundlich model. The maximum adsorption capacities of the unmodified and modified NPs, respectively, were found to be 11.8 and 19.8 mg DNA per gram of adsorbent. The adsorption of DNA onto the modified NPs was endothermic, while it was exothermic in the case of the unmodified NPs. The DNA can be desorbed from the modified surfaces of the NPs by using EDTA as the eluent. The NPs were able to adsorb about 90?±?1.5 % of DNA after being recycled for three times. The method is simple, fast, robust, and does not require organic solvents or sophisticated equipment.

Adsorption characteristics of Titan yellow and Congo red on CoFe2O4 magnetic nanoparticles

This paper assesses the adsorption characteristics of Titan yellow and Congo red on CoFe₂O₄ magnetic nanoparticles. The adsorption behavior of Titan yellow and Congo red from aqueous solution onto CoFe₂O₄ magnetic nanoparticles has been determined by investigating the effects of pH, concentration of the dye, amount of adsorbent, contact time, ionic strength and temperature. Experimental results indicated that CoFe₂O₄ nanoparticles can remove more than 98 % of each dye under optimum operational conditions of a dosage of 15.0 mg CoFe₂O₄, pH 3.0, initial dye concentration of 22–140 mg L^?1, and contact times of 2.0 and 15.0 min for Congo red and Titan yellow, respectively. Langmuir and Freundlich isotherm models have been used to evaluate the ongoing adsorption kinetic equations. Regeneration of the saturated adsorbent was possible by NaCl/acetone solution as eluent. The maximum adsorption capacities were 200.0 and 212.8 mg dye per gram adsorbent for Congo red and Titan yellow, respectively. With the help of adsorption isotherm, thermodynamic parameters such as free energy, enthalpy and entropy have been calculated. On the basis of pseudo-first-order and pseudo-second-order kinetic equations, different kinetic parameters have been obtained.     

Kinetic-catalytic determination of vanadium(IV) using methyl orange-bromate redox reaction.

Determination of V(IV) based on its catalytic effect on the reaction between Methyl Orange and bromate in thepresence of citric acid was studied. The calibration curve obtained by fixed-time method was linear in the range of 2.5-300 ng ml(-1). By use of slope method, a calibration curve containing two linear portions were obtained. Using fixed-time and slope methods, we obtained detection limits of 0.8 and 1.5 ng ml(-1), respectively. Fe2+, As(III), V(V) and Hg2+ interfered. The method was successful for analysis of water samples.     

Optimized mercapto-modified resorcinol formaldehyde xerogel for adsorption of lead and copper ions from aqueous solutions

Journal of Sol-Gel Science and Technology - Resorcinol formaldehyde (RF) xerogel was modified by mercapto functional groups for removal of Pb(II) and Cu(II) ions from aqueous solutions. The...     

Micro-extraction and determination of transition metals in historical ink

A minimally invasive approach is described for sampling Fe, Cu, Zn and Mn in iron-gall ink. Filter paper (2?×?5 mm) that is moistened with de-ionized water is used to extract metals from an iron-gall ink surface. The extraction requires about 30–120 s for a small quantity of ink to diffuse into the moistened filter paper. The metals in the ink are extracted from the filter paper using 50 µL of concentrated nitric acid in a 2 mL polystyrene beaker for approximately 10 min. Graphite furnace atomic absorption spectrometry (GFAAS) was used to quantify Fe, Cu, Zn and Mn in iron-gall ink. In order to test the feasibility of this extraction procedure, the ratio of Fe:Cu was determined from ink lines that were drawn with a commercially available iron-gall ink on modern acid-free paper. The measured ratio of Fe:Cu was 18.2:1 which is comparable to the expected ratio of 20:1. The slightly lower ratio achieved using the extraction procedure and GFAAS was possibly due to the higher solubility of the Cu species in the ink. One of the advantages of using a moistened filter paper is that only the ink surface is sampled which avoids the possible measurement of metals of different inks of other components that may be present in the paper or on the opposite side of the paper.     

Fabrication of an electrochemical sensor based on computationally designed molecularly imprinted polymers for determination of cyanazine in food samples

A computational approach was used for screening functional monomers and polymerization solvent in the rational design of molecularly imprinted polymers (MIPs). It was based on the comparison of the binding energy of the complexes between the template and functional monomers. On the basis of computational results, acrylamide (AAM) and toluene were selected as functional monomer and polymerization solvent, respectively. The MIP, embedded in the carbon paste electrode, functioned as a selective recognition element and pre-concentrator agent for cyanazine determination by using cathodic stripping voltammetric method. The MIP-CP electrode showed very high recognition ability in comparison with NIP-CPE. Some parameters affecting the sensor response were optimized, and then the calibration curve was plotted. A dynamic linear range of 5.0–1000 nM was obtained. The detection limit of the sensor was calculated as 3.2 nM. This sensor was successfully used for cyanazine determination in food samples.