Zwitterionic titanoxanes {Cp[η-C5H4B(C6F5)3]Ti}2O and {(η-PrC5H4)[η-1,3-PrC5H3B(C6F5)3]Ti}2O as catalysts for cationic ring-opening polymerization

Zwitterionic titanoxanes {Cp[η⁵-C₅H₄B(C₆F₅)₃]Ti}₂O (I) and {(η⁵-ⁱPrC₅H₄)[η⁵-1,3-ⁱPrC₅H₃B(C₆F₅)₃]Ti}₂O (II), which contain two positively charged Ti(IV) centres in the molecule, are able to catalyse the ring-opening polymerization of -caprolactone (-CL) in toluene solution and in bulk. The process proceeds with a noticeable rate even at room temperature and accelerates strongly on raising the temperature to 60 °C. The best results have been obtained on carrying out the reaction in bulk. Under these conditions, the use of I as a catalyst (-CL:I = 1000:1) gives at 60 °C close to quantitative yield of poly--CL with the molecular mass of 197 000. An increase in the -CL:I ratio to 6000:1 increases the molecular mass of poly--CL to 530 000. Tetrahydrofuran (THF) is also polymerized under the action of I albeit with a lesser rate. However, the molecular mass of the resulting poly-THF can reach rather big values under optimal conditions (up to 217 000 at 20 °C and the THF:I ratio of 770:1). A rise in the reaction temperature from 20 to 60 °C results here to a decrease in the efficiency of the process. Titanoxane II is close to I in its catalytic activity in the -CL polymerization but it is much less active in the polymerization of THF. Propylene oxide (PO), in contrast to -CL and THF, gives with I only liquid oligomers in wide temperature and PO:I molar ratio ranges (−30 to +20 °C, PO:I = 500–2000:1). γ-Butyrolactone and 1-methyl-2-pyrrolidone are not polymerized under the action of I at room temperature. The reactions found are the first examples of catalysis of the cationic ring-opening polymerization by zwitterionic metallocenes of the group IVB metals.     

Reduction of 1,4-dichlorobut-2-yne by titanocene to a 1,2,3-butatriene. Formation of a 1-titanacyclopent-3-yne and a 2,5-dititanabicyclo[2.2.0]hex-1(4)-ene

The 2,5-dititanabicyclo[2.2.0]hex-1(4)-ene (bis-titanocene-mu-(Z)-1,2,3-butatriene complex)3 is formed starting from [Cp2Ti(eta2-Me3SiC2SiMe3)] by in situ generated titanocene and 1,4-dichlorobut-2-yne via the 1-titanacyclobut-3-yne (2).     

Influence of solvents on the insertion of methacrolein into zirconacyclopropenes

The reaction of Cp₂Zr(L)(η²-Me₃SiC₂) (L = THF, py) with equimolar amounts of H₂C = CMe-CHO at room temperature depends strongly on the ligands L and the solvents that are used. With L = THF, in the THF solution the insertion product

Full-size image

1 was isolated, whereas by conducting the reaction in n-hexane solution an alkyne substitution with 1,4-coordination of the methacrolein takes place and the binuclear complex [

Full-size image

2 was obtained. In conttrast, with L = py (a stronger ligand) only a 1:1 ratio of 1 and 2 was observed in both THF and in n-hexane. At 50°C complex 1 was converted into 2 and the alkyne was eliminated quantitatively.

Complexes 1 and 2 were characterized by IR and NMR spectroscopical measurements and 1 by an additional X-ray structure determination.     

Monte Carlo simulation of growth of porous SiOx by vapor deposition

A random network model containing defects has been developed and applied to the deposition of amorphous SiOx films on a flat substrate. A new Monte Carlo procedure enables dangling bonds to migrate and annihilate. The degree of porosity in the films is found to increase with oxygen content. As the oxygen content increases a larger fraction of pore surfaces is covered with oxygen, and the density of dangling bonds on pore surfaces decreases. Oxygen plays the role of a surfactant, lowering the energies of pore surfaces and enhancing the porosity of amorphous SiO2 compared to amorphous Si.     

Damage in lithium niobate induced by a high-power proton-carbon beam

Surface damage in lithium niobate LiNbO₃ induced by a high-power proton-carbon beam was investigated. Typical damage patterns were observed. The effect of thin metal surface coating on the damage was considered.