Influence of heat treatment conditions on the porosity changes of sulfonated styrene/divinylbenzene copolymers

Sulfonic cation exchangers with two ion exchange group concentrations (0.5 and 2.4 mmol/g, samples A and B, respectively) were obtained by sulfonation of a porous styrene (S) and divinylbenzene (DVB) copolymer with chlorosulfonic acid. Strong thermal decomposition of the sulfonated copolymer A, accompanied by significant changes in its porous structure, starts at ca. 400°C. The char has no sulfonic groups. After heat treatment at 400°C in steam, a sorbent was obtained (yield 65%) that shows higher phenol sorption than the untreated sample when related to the bed volume. The chlorosulfonic derivatives of the initial copolymer were less thermally resistant than the sulfonic ones obtained by hydrolysis. Pyrolysis of the cation exchanger B, in its H+ and Ca²⁺ forms, was carried out at 900°C (yield of both chars close to 30%). By subsequent steam activation at 800°C to a 50% burn-off of the char, sorbents with well-developed, but distinctly different, porous structures were obtained. The activated char from the sulfonated copolymer in its hydrogen form was highly microporous and indicated an effective surface area of 1180 m²/g. However, because of a low contribution of mesopores, its ability to adsorb phenol from the liquid phase was not very high. The activated char from the calcium-doped copolymer, indicating a smaller surface area (580 m²/g) but characterized by a well-developed mesoporosity, was a better sorbent for phenol. © 1994 John Wiley & Sons, Inc.     

Simple method for the determination of trace levels of pesticides in honeybees using matrix solid-phase dispersion and gas chromatography

A simple multiresidue method for the determination of insecticides in honeybees is described. The developed method is based on the matrix solid-phase dispersion technique. A total number of 12 insecticides (azinfos-methyl, buprofezin, chlorpyriphos, chlorpyriphos-methyl, diazinon, ethion, fenitrothion, fipronil, methidathion, phosalone, pirimicarb, propoxur) used on flowering fields are determined by this method. The method uses Florisil and silica as dispersing agents, alumina and silica as cleanup adsorbents and a low polarity solvent system to elute pesticide residues from the honeybee samples. The insecticides were quantified using capillary gas chromatography with a nitrogen-phosphorus detector. The method has shown good recovery (70-110%) for various levels of spiked samples (0.01-1.0 mg/kg). The relative standard deviations were in the range of 2-8% for all pesticides studied. The limits of detection were in the range of 0.005-0.05 mg/kg. The procedure can be applied for the determination of residues of low-polarity and medium polarity pesticides in honeybee samples.     

Cationic Heteroconjugation Constants in the OHN+ and NHO+ Systems in Propylene Carbonate: Dependence on Difference in Basicity

Cationic heteroconjugation equilibria of more than ninety systems consisting of substituted pyridines, their N-oxides, and trimethylamine N-oxide, i. e., in systems with mixed hydrogen bridges of type OHN⁺ (NHO⁺) were studied in propylene carbonate. Both experimental systems without proton transfer, BH⁺/B₁, and those with proton transfer, B₁H⁺/B, were explored. The stability of the mixed hydrogen bridges, OHN⁺ (NHO⁺), is compared with that of the OHC⁺-type bridges. The influence of the difference in basicity of the conjugate base of the proton donor and the proton acceptor on the presence of the proton transfer equilibria, and, consequently, the possibility of determination of the cationic heteroconjugation constant values is discussed.     

Simple formula for nuclear charge radius

A new formula for the nuclear charge radius is proposed, dependent on the mass numberA and neutron excessN-Z in the nucleus. It is simple and it reproduces all the experimentally available mean square radii and their isotopic shifts of even-even nuclei much better than other frequently used relations.This work is partly supported by the Polish Committee of Scientific Research under contract No. 203119101     

The influence of chitosan on in vitro properties of Eudragit RS microspheres

Eudragit RS microspheres containing chitosan hydrochloride were prepared by the solvent evaporation method using acetone/liquid paraffin solvent system and their properties were compared with Eudragit RS microspheres without chitosan, prepared in our previous study. Different stirring rates were applied (400-1200 rpm) and drug content, Higuchi dissolution rate constant, surface and structure characteristics of the microspheres were determined for each size fraction. An increase in average particle size with a reduction of stirring rate appeared in limited interval in both series. The average particle size of microspheres without chitosan, prepared at the same stirring rate, was smaller. Pipemidic acid content increased with increasing fraction particle size, but not with increasing stirring rate as it was observed for microspheres without chitosan. We presume that high pipemidic acid content in larger microspheres is a consequence of cumulation of undissolved pipemidic acid particles in larger droplets during microspheres preparation procedure. Pipemidic acid release was faster from microspheres with chitosan and no correlation between Higuchi dissolution rate constant and stirring rate or fraction particle size was found, though it existed in the system without chitosan. Structure and surface characteristics of microspheres observed by scanning electron microscope (SEM) were not changed significantly by incorporation of chitosan. But in contrast with microspheres without chitosan, the surface of chitosan microspheres was more porous after three hours of dissolution. It is supposed that the influence of particle size fraction and stirring rate on release characteristics is expressed to a great extent through porosity and indirectly through total effective surface area, but the incorporation of highly soluble component i.e. chitosan salt hides these effects on drug release. In conclusion, changes in biopharmaceutical properties due to varying stirring rate and fraction particle size exhibited the same direction as those reported for the microspheres without chitosan, although they are less expressed because of increased experimental variability, likely caused by chitosan.     

Plasma enhanced aerosol–gel method: a new way of preparing ceramic coatings

The sol–gel process is widely used for the production of powders, coatings and bulk materials. However, being a wet-chemical technique, it has certain limitations related to properties of aqueous colloidal solution, especially when applied as a coating. The most frequently used methods, such as dip- and spin-coating, are difficult to apply onto more complex substrates. In these cases, the aerosol–gel deposition method can be regarded as the solution of this problem. In the present article, a novel plasma enhanced aerosol–gel method of coatings production is presented. A novelty of this method is based on an integration of the aerosol–gel deposition of thin films and their low temperature plasma treatment. Owing to the above, all stages of the coatings production process—substrate preparation, film deposition, and its plasma treatment, can be carried out in a single reactor. The design and operational scheme of such device is presented in this work. Using this device, thin coatings were first deposited on substrates and then plasma treated. The effect of deposition and plasma discharge conditions on morphology and chemical structure of the films has been studied. It was found that plasma treatment had a substantial influence on all the examined properties of the aerosol–gel deposited coatings.     

Preparation of Sec-Alkyl Isouronium Salts

Eight examples of sec-alkyl isouronium salts were readily prepared from sec-alcohols, cynamide, and methanesulfonic acid (or CF₃SO₃H or HBF₄).     

Behaviour of Phenoxyacetic Acids During Underground Passage with Different Redox Zones

Abstract

The behaviour of the three phenoxyacetic acid herbicides 2,4-D, 2,4,5-T and MCPA during underground passage and bankfiltration was tested in a model system consisting of laboratory filter columns filled with natural underground materials. Different redox environments were reproduced by operating the filters with natural aerobic and anaerobic groundwater. In the presence of oxygen, biodegradation of the three herbicides started after a lag phase. Under sulfate reducing conditions, no degradation could be observed. To assess the factors that may influence microbial degradation in the anaerobic environment, the concentration of herbicides, the time and the nutrient content were varied, but this did not increase degradation. The maximum retention of the herbicides in the filters was 30%, mainly due to adsorption to the filter material.     

Theranostic Approach for the Protein Corona of Polysaccharide Nanoparticles

Polysaccharide nanoparticles are promising materials in the wide range of disciplines such as medicine, nutrition, food production, agriculture, material science and others. They excel not only in their non‐toxicity and biodegradability but also in their easy preparation. As well as inorganic particles, a protein corona (PC) around polysaccharide nanoparticles is formed in biofluids. Moreover, it has been considered that the overall response of the organism to nanoparticles presence depends on the PC. This review summarises scientific publications about the structural chemistry of polysaccharide nanoparticles and their impact on theranostic applications. Three strategies of implementation of the PC in theranostics have been discussed: I) Utilisation of the PC in therapy; II) How the composition of the PC is analysed for specific disease markers; III) How the formed PC can interact with the immune system and enhances the immunomodulation or immunoelimination. Thus, the findings from this review can contribute to improve the design of drug delivery systems. However, it is still necessary to elucidate the mechanisms of nano‐bio interactions and discover new connections in nanoscale research.     

Dynamic rotational characteristics of actinides on empirical approach

In the paper calculation of the moments of inertia for nuclei from the region 87 ≤ Z ≤ 100 and 130 ≤ N ≤ 156 was made in dependence on the angular momentum of their rotational states. The experimental values of the moments of inertia were calculated for rotational energy of the classic rotor in its quantum form, with the use of a simple formula. The moment of inertia term appearing in the formula was treated as a variable. The calculations were carried out on the basis of experimental data for the energies of the rotational levels for 51 bands built on ground states for even-even nuclei and for nuclei with odd mass number A. In addition, 30 rotational bands built on excited states were also analysed in the investigated region in case of even-even nuclei. For many bands and nuclei the considered dependence of the moment of inertia on angular momentum has been found in the analytical form by fitting polynomials to the experimental data. It turned out that obtained results for the moments of inertia made it possible to describe the energies of rotational levels with a relative deviation not greater or only slightly greater than 1%. In general, in the case of 12 bands of ground level the maximum relative deviation of obtained level energies is smaller than 1%.