Inside-Needle Extraction Method Based on Molecularly Imprinted Polymer for Solid-Phase Dynamic Extraction and Preconcentration of Triazine Herbicides Followed by GC–FID Determination

An inside-needle extraction method was developed through thermal polymerization of atrazine-molecularly imprinted polymer (MIP) on the internal surface of a stainless steel hollow needle, which was oxidized and silylated. The fabricated coating (MIP layer) for the needle was durable and showed very good chemical and thermal stability. It could be mounted on a glass syringe and be directly coupled with gas chromatographic (GC) systems. The parameters being effective on the coating and extraction processes, namely nature of oxidizing agent, silylation time, nature and amount of porogen, template-to-MIP components ratio, polymerization time and temperature, sample volume, flow rate, pH and ionic strength of the sample were investigated and optimized. The extraction needle showed high selectivity as well as a great extraction capacity for triazines. The extraction of atrazine, simazine, cyanazine, ametryn, prometryn and terbutryn using the fabricated extraction needle and followed by GC analysis resulted in detection limits of 2.6, 21, 24, 32, 38 and 42 ng mL⁻¹, respectively. The fabricated needle proved to be applicable to the analysis of real samples by comparing the results obtained for non-spiked and spiked samples of grape juice, tap water and groundwater.

     

The effect of turbulence intensity on film cooling of gas turbine blade from trenched shaped holes

This paper reports a computational investigation on the effects of mainstream turbulence intensity on film cooling effectiveness from trenched holes over a symmetrical blade. Computational solutions of the steady, Reynolds-Averaged Navier–Stokes equations are obtained using a finite volume method with k − ε Turbulence model. Whenever possible, computational results are compared with experimental ones from data found in the open literature. Computational results are presented for a row of 25° forward-diffused film hole within transverse slot injected at 35° to AGTB symmetrical blade. Four blowing ratios, M = 0.3, 0.5, 0.9 and 1.3 are studied together with four mainstream turbulence intensities of Tu = 0.5, 2, 4 and 10%. Results indicate that the trenched shaped holes tend to give better film cooling effectiveness than that obtained from discrete shaped holes for all blowing ratios and all turbulence intensities. The trenching of shaped holes has changed the optimum blowing ratio and also the location of re-attachment of separated jet at high blowing ratios. Moreover, it has been found that the effect of mainstream turbulence intensity for trenched shaped holes is similar to that obtained for discrete shaped holes with the exception that the sensitivity of film cooling effectiveness to turbulence intensity has decreased for trenched shaped holes.     

Determination of methamphetamine, amphetamine and ecstasy by inside-needle adsorption trap based on molecularly imprinted polymer followed by GC-FID determination

We have developed a solvent-free and sensitive method for the identification and quantification of methamphetamine (MAMP), amphetamine (AMP) and ecstasy (MDMA) in human urine. It is based on the use of an inside-needle adsorption trap (INAT) and a molecularly imprinted polymer (MIP). The MAMP-MIP layer was coated on the internal surface of a hollow stainless steel needle, which was oxidized and silylated. It was used as the extraction needle. A model solution containing the drugs was slowly passed through the extraction needle. After adsorption of the analytes, the needle was directly transferred to the injector of a gas chromatograph, where the analytes were thermally desorbed, separated by GC, and detected with a flame ionization detector. The method does not require an extraction solvent, is fast and simple. The linear range of the calibration graphs are rather wide, and the limit of detection and the limit of quantification (LOQ) for MAMP are 12 and 40?ng?mL^?1, respectively. The relative standard deviations (RSD%) for six repeated experiments (at 500?ng?mL^?1 of MAMP) is 4.9?%. The relative recoveries obtained for MAMP in spiked human urine samples are in the range of 81–93?%.

Synthesis and Application of High Selective Monolithic Fibers Based on Molecularly Imprinted Polymer for SPME of Trace Methamphetamine

A monolithic solid-phase microextraction (SPME) fiber was fabricated based on a molecularly imprinted polymer which could be coupled with gas chromatography for extraction, pre-concentration and determination of methamphetamine (MAMP). Methacrylic acid, ethylene glycol dimethacrylate and MAMP play the roles of functional monomer, cross-linker and template, respectively. The effective factors influencing the polymerization and extraction procedures were investigated and will be detailed here. The fabricated fiber was firm, inexpensive, stable, selective and durable which gives it vital importance in SPME. Selectivity of the fabricated fiber in relation to the template in solution containing MAMP, related and unrelated compounds was also investigated. Under the optimum conditions, the calibration plot was linear in the range of 50?C3,500 ng mL^?1 (r ²  = 0.997). The high extraction efficiency was obtained for MAMP giving a detection limit of 14 ng mL^?1. The fabricated fiber was successfully applied to SPME of MAMP from human saliva samples followed by gas chromatography-flame ionization detector analysis.     

Developing a novel packed in‐tube solid‐phase extraction method for determination ∆9‐tetrahydrocannabinol in biological samples and cannabis leaves

A novel plate‐like nano‐sorbent based on copper/cobalt/chromium layered double hydroxide was synthesized by a simple coprecipitation method. The synthesized nanoparticels were introduced into a stainless steel cartridge using a dry packing method. Then, the packed cartridge was introduced as a novel on‐line “packed in‐tube” configuration and followed by high performance liquid chromatography for the determination of trace amounts of ^?9‐tetrahydrocannabinol from biological samples and cannabis leaves. The as‐prepared sorbent exhibited long lifetime, good chemical stability, and high anion‐exchange capacity. Several important factors affecting the extraction efficiency, such as extraction and desorption times, pH of the sample solution and flow rates of the sample and eluent solutions, were investigated and optimized. Under optimized conditions, this method showed good linearity for ^?9‐tetrahydrocannabinol in the ranges of 0.09–500, 0.3–500, and 0.4–500 µg/L with coefficients of determination of 0.9999, 0.9991, and 0.9994 in water, serum and plasma samples, respectively. The inter‐ and intra‐assay precisions (n = 3) were respectively in the ranges of 1.8–4.6% and 1.9–4.0% at three concentration levels of 10, 50, and 100 µg/L. The limits of detection were also in the range of 0.02–0.1 µg/L.     

Preparation and evaluation of solid-phase microextraction fibers based on monolithic molecularly imprinted polymers for selective extraction of diacetylmorphine and analogous compounds

All of the studies on solid-phase microextraction based on molecularly imprinted polymers up to now have been carried out on the synthesis of the polymer on the surface of the fiber which is brittle and the polymer coating strips during handling. The objective of this study was to develop a method for fabrication of a monolithic and robust solid-phase microextraction fiber on the basis of molecularly imprinted polymer for selective extraction of diacetylmorphine and its structural analogues followed by their GC or GC/MS analysis. A fiber was produced by copolymerization of methacrylic acid-ethylene glycol dimethacrylate imprinted with diacetylmorphine. The effective factors influencing the polymerization have been investigated and are detailed here. Also, the influences of pH, extraction time and temperature on the extraction efficiency of analytes were investigated. The prepared fiber was thermally stable up to 300 degrees C which has vital importance in SPME coupled with GC or GC/MS. The adsorption isotherm modeling was performed by fitting the data of studied compounds to bi-Langmuir isotherm model. The evaluated equilibrium constants for diacetylmorphine were 0.011 and 1824.72 microM(-1), and the number of binding sites was 170.37 and 4.64 nmolg(-1), respectively. This fiber was successfully used for extraction of template molecule from aqueous solution and further analysis with GC or GC/MS. The high extraction efficiency was obtained for diacetylmorphine, 6-monoacetylcodeine, and 6-monoacetylmorphine, yielding the detection limits of 300, 47, and 1 ngmL(-1), respectively.     

A percolation model for carbon nanotube-polymer composites using the Mandelbrot-Given curve

A model is introduced for the conductivity of carbon-nanotube polymer composites based upon percolation theory and fractals. These types of polymer composites have been developed in the recent years, and experimental data on their percolation threshold is available. We constructed a fractal space with the aim of the generalized Mandelbrot-Given curve and used the experimental critical exponent of conductivity to calculate the parameters of such a curve. Finally, the moments of the current distribution function are estimated, and the effect of the critical exponent on this function is investigated.     

Liquid‐phase microextraction based on two immiscible organic solvents followed by gas chromatography with mass spectrometry as an efficient method for the preconcentration and determination of cocaine,ketamine, and lidocaine in human urine samples

A new type of liquid‐phase microextraction based on two immiscible organic solvents was optimized and validated for the quantification of lidocaine, ketamine, and cocaine in human urine samples. A hollow‐fiber based microextraction technique followed by gas chromatography coupled with mass spectrometry detection was used to reduce matrix interferences and improve limits of detection. The analytes were extracted from aqueous sample with pH 11.0, into a thin layer of organic solvent (n‐dodecane) sustained in the pores of a hollow fiber, and then into a second organic acceptor (acetonitrile) located inside the lumen of the hollow fiber. With the application of optimized values, good linearity was obtained in the range of 1–500 μg/L for lidocaine and ketamine and 2–500 μg/L for cocaine with the determination coefficient values (r²) >0.9943. The preconcentration factors and limits of detection (S/N > 3) were 250–350 and 0.01–0.05 μg/L, respectively. Intra and interassay precision values were <7.3 and 9.3%, respectively. The method was successfully applied for the determination and quantification of target analytes in human urine samples.     

Classification of methamphetamine seized in different regions of Iran using GC–MS and chemometrics

According to the intensive physical and mental risk of methamphetamine (crystal) on human, it is important to focus on the prevention of distribution and decrease of the usage of methamphetamine. In the current study, attempts was on the application of GC–MS analysis combined with chemometrics to present a classification model for methamphetamine samples seized in different regions of Iran. In this work, principal component analysis was not able to discriminate samples from different geographic regions. For the discrimination goal, partial least squares discriminant analysis (PLS-DA) and extended canonical variate analysis (ECVA) were utilized and a classification model was constructed to differentiate methamphetamine samples seized in three regions of Iran, i.e., south, west and central. PLS-DA showed good performance in calibration step; however, ECVA indicated better prediction ability. The difference of the classified samples can be because of difference in the synthetic root used in each of three investigated regions. Class sensitivity and selectivity for all three regions were excellent in ECVA model with nonsignificant misclassifications. Cross-validation and external validation using a test set confirmed the obtained classification model. Statistical results indicated a regional production/distribution pattern in the country.     

Development of Electro Solid-Phase Microextraction and Application to Methamphetamine Analysis

A new electro solid-phase microextraction (El-SPME) technique using homemade pencil-lead fibers has been developed as an effective means of selective extraction of methamphetamine before analysis by gas chromatography (GC) and gas chromatography–mass spectrometry (GC–MS). The methamphetamine was extracted by use of a laboratory-made El-SPME cell with three electrodes—the pencil-lead SPME fiber, Ag/AgCl, and platinum as working, reference, and auxiliary electrodes, respectively. A negative potential was applied to the homemade pencil-lead fiber during extraction. Experimental conditions, for example type of pencil-lead fiber, conditions for modification of the fiber, extraction time, applied potential, pH, and gas chromatographic conditions were optimized. Methamphetamine was identified by GC–MS. Screening of the extracted compounds showed that the proposed El-SPME technique is much more selective than direct SPME using a commercially available polyacrylate fiber. Under the optimum conditions the calibration plot for the compound was linear in the range 50–3,200 ng mL⁻¹ and the detection limit was 34 ng mL⁻¹.