Theoretical study on the adsorption of aromatic compounds on platinum clusters

B3 LYP hybrid functional with LACVP* pseudopotential was applied for the optimization of geometries of complexes resulting from interaction of benzene, pyridine, naphthalene, and quinoline with Pt_n (n = 4, 7) clusters. For benzene‐containing complexes, the most stable form corresponds to a bridge adsorption, with benzene undergoing considerable geometric distortions, assuming a boat‐like conformation. C? H bonds are bended upward from the plane of the cluster. C? C bonds stretch, especially when they form π‐complexes with low coordinated Pt atoms. Some arrangements for pyridine complexes involving the N atom of the organic moiety undergo further distortions, apparently preserving a formal C? N π bond. Except for that distortion, the behavior of any heteroaromatic complex is similar to that of benzene in the same arrangement. The quinoline–Pt₇ complex can suitably be used for simulation of the cinchonidine (CD) anchorage over Pt. © 2003 Wiley Periodicals, Inc. Int J Quantum Chem, 2003     

Determination of arsenic in sediments, coal and fly ash slurries after ultrasonic treatment by hydride generation atomic absorption spectrometry and trapping in an iridium-treated graphite tube

A simple and reliable method for the determination of arsenic in sediment and in coal without sample digestion, based on hydride generation from slurry samples is proposed. After grinding the samples to a particle size of 50 μm, the sample powder was mixed with aqua regia and hydrofluoric acid in an ultrasonic bath for 30 min. After diluting the mixture with hydrochloric acid, the slurry was allowed to stand for 48 h, and an aliquot was used for hydride generation with sodium borohydride. More than 80% of the arsenic was leached to the aqueous phase under these conditions, except for one sediment sample with very high silica content. The generated arsine was collected in a graphite tube, treated with 0.5 mg of iridium as a permanent modifier, and the arsenic determination was carried out by electrothermal atomic absorption spectrometry. The same tube could be used for at least 160 cycles without any re-treatment. The greatest advantage of the method was that only a minimum of reagents and sample handling were required, reducing the risks of contamination and/or analyte loss. However, the addition calibration technique had to be used in order to obtain results within the 95% confidence level for 11 certified reference materials, 5 sediments, 5 coals and one coal fly ash. One certified sediment slurry was spiked with the analyte and the resulting addition calibration curve was used for the analysis of the certified sediments. Similarly, one certified coal was used to obtain the addition calibration curve for the coal and coal fly ash samples. The recoveries of the certified values, except for one sediment, were between 91 and 115%. The limits of detection in the samples were 0.54 and 0.7 μg g⁻¹ for the coal and sediment samples, respectively, obtained for 1 ml of slurry containing 1 mg of sample.     

Biotransformation of (−)β-pinene by Aspergillus niger ATCC 9642

The main objective of this work was to investigate the biotransformations of (−)α-pinene, (−)β-pinene, and (+) limonene by Aspergillus niger ATCC 9642. The culture conditions involved—concentration of cosolvent (EtOH), substrate applied, and sequential addition of substrates—were investigated. Adaptation of the precultures with small amounts of substrate was also studied. The experiments were performed in conical flasks with liquid cultures. This strain of A. niger was able to convert only (−)β-pinene into α-terpineol. An optimum conversion of (−)β-pinene into α-terpineol of about 4% was obtained when the substrate was applied as a diluted solution in EtOH and sequential addition of substrate was used.     

Mixed systems of hydrophobically modified polyelectrolytes: controlling rheology by charge and hydrophobe stoichiometry and interaction strength

Rheology and phase separation were investigated for aqueous mixtures of two oppositely charged hydrophobically modified polyelectrolytes. The typical phase separation, normally seen for oppositely charged polymer mixtures, is dramatically reduced by the presence of hydrophobic modification, and phase separation is only detected close to the point of charge neutralization. While the two polyelectrolytes separately can give high viscosities and a gel-like behavior, a pronounced maximum in viscosity and storage modulus with the mixing ratio of the polyelectrolytes is observed; the maximum is located between the points of charge and hydrophobe stoichiometry and reflects a combination of hydrophobic and electrostatic association. Lowering the charge density of the anionic polymer leads to a strengthened association at first, but at lower charge densities there is a weakened association due to the onset of phase separation. The strength of the electrostatic interaction was modified by adding salt. Increased ionic strength can lead to phase separation and to increased or decreased viscosity depending on the polyelectrolyte mixing ratio.     

Latex Fractionation by Sedimentation and Colloidal Crystallization: The Case of Poly(styrene-co-acrylamide)

Poly(styrene-co-acrylamide) (PS-AAM) latex was prepared, fractionated by sedimentation under gravity, and characterized by PCS, infrared spectra, secondary and backscattered electron imaging in the scanning electron microscope, and electron spectroscopy imaging in an analytical transmission electron microscope. Three latex fractions were obtained. The lower fraction was opalescent and its particles were the more uniform, concerning size, chemical composition, and topochemical features. This lower fraction was still further fractionated by zonal centrifugation in a density gradient, yielding two fractions with similar macrocrystal-forming abilities but different sizes and chemical compositions. These results confirm those previously obtained for the PS-HEMA latex. Copyright 2000 Academic Press.     

Uranium (III) scorpionates: synthesis and structure of [(TpMe2)2U[N(C6H5)2]] and [(TpMe2)2U[N(SiMe3)2]

Reaction of [(Tp(Me)2)(2)UI] with KNR(2) (R = C(6)H(5), SiMe(3)) in tetrahydrofuran (THF) afforded the monomeric trivalent actinide amide complexes [(Tp(Me)2)(2)U[N(C(6)H(5))(2)]], 1, and [(Tp(Me)2)(2)U[N(SiMe(3))(2)]], 2. The complexes have been fully characterized by spectroscopic methods and their structures were confirmed by X-ray crystallographic studies. In the solid state 1 and 2 exhibit distorted pentagonal bipyramidal geometries. The U-NR(2) bond lengths in both complexes are the same but in complex 2 the greater steric demands of the N(SiMe(3))(2) ligand led to elongated U-N(pz) bonds, especially those opposite the amido ligand.