The pentacene films on the glass/ITO surface: structure and optical properties

Abstract

The structure, morphology and optical transmittance spectra of pentacene films on the (glass/ITO) surface were studied. The films were grown by two methods - the thermal vacuum deposition (TVD) and pulsed laser deposition (PLD). The electron diffraction pattern from thermally deposited pentacene films confirms their polycrystalline structure while the diffraction pattern of PLD-coated layers has a diffusion character. The results obtained showed that layers deposited by the TVD method has an optical spectrum that is characteristic for the pentacene film in contrary to the layers deposited by the PLD method. It is found a sensitivity of the optical transmittance of pentacene films to the ammonia action, which may be used for development the optical gas sensor.     

Molecular structure,vibrational spectroscopic and chemical reactivity of nematogenic p-n-alkylbenzoic acids: A comparative computational analysis

Molecular structure and vibrational spectroscopic studies of higher homologous series nematogenic p-n-alkylbenzoic acids (nBAC) that have 6 (6BAC) and 7 (7BAC) carbon atoms in the alkyl chain have been investigated using the Density Functional Becke3-Lee-Yang-Parr (B3LYP) level with the basis set 6-31++G (d.p) and Hartree Fock (HF) with the same basis set. The observed vibrational spectra has been resolved and assigned in detail for comparision with both the molecules. These results indicate that DFT and HF values are slightly different at both the levels. A comparision of chemical reactivity such as HOMO (E_H), LUMO (E_L) energies, energy gap (E_g), ionization energy (I), electron affinity (A), electro negativity (χ), chemical hardness (η), electronic chemical potential (μ), electrophilicity index (ω), and softness (S) has been made. It has been observed that the decrement has occurred in the energy band gap value of isolated molecule with increment in alkyl chain length. This provides valuable information regarding enhancing the stability of liquid crystal materials by maintaining the conductivity.     

Entropic effect implication for change in polymer coils swelling state in the demixing enthalpy recovery of aqueous poly(vinyl methyl ether) solutions

Time‐dependent demixing enthalpy recovery behavior of aqueous poly(vinyl methyl ether) (PVME) solutions exhibits distinct recovery characteristics in three concentration regions. The absence of recovery behavior below a water concentration of 38.3 wt % indicates that the PVME coil is in a globular state. The typically sigmoidal recovery behavior of demixing enthalpy above 38.3 wt % is ascribed to the reswelling of the collapsed polymer coils induced by the entropic effect. The increase in difference between the upper and lower limits indicates the continued swelling of the PVME coils. Above 65 wt %, a dominant diluting effect can be observed, and a much longer phase separation time is needed to reach the expected lower limit. In contrast, the recovery of demixing enthalpy in a wide range of water concentration (from 38.3 to 90 wt %) exhibits the same feature. The infrared spectroscopy results are in agreement with the above macroscopic differential scanning calorimetry results. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 142–151     

常压下玉米秸秆液化工艺的优化及其生物油分析

随着化石能源的日益短缺，可再生木质生物质资源的利用越来越受到重视，常压液化技术是生物质资源高效利用的主要方式之一。利用单因素方法，探讨液化温度、复配液化剂二甘醇（DEG）与1,2-丙二醇（PG）的混合比、液固比、催化剂磷酸的用量、反应时间等因素对玉米秸秆液化得率的影响，以便优化其液化工艺；然后采用热重分析仪（TGA）、气相色谱-质谱技术（GC-MS）和核磁共振（NMR）技术对此优化条件下所得生物油的挥发降解特性和主要组成成分进行了检测探讨。分析表明，玉米秸秆液化时优化工艺参数为：液化温度170 ℃，液化剂DEG与PG混合比1∶2，液固比5∶1，H₃PO₄用量10%，反应时间45 min；此时玉米秸秆液化得率高至99.50%。TGA结果表明，此条件下所得生物油含有80%以上碳数小于25的化合物，热解后最终残炭量约为15%。GC-MS表明，可以检测出此生物油中含有的39种有机物，其中，醇类有机物的含量最多，酚类有机物的含量次之，它们相对含量依次是70.70%和25.63%，其还含有一定量的有机酸（2.80%）、醚类（0.64%）、酯类（0.10%）和酮类（0.13%）等有机物；其组分十分复杂，高含氧量，稳定性较差。1H-和13C-NMR分析表明，不同化学位移δ与生物油中不同类型的质子和碳原子相对应，明确生物油中不同类型H和C的分布，有利于对其分子结构进行深入探讨。这些研究为非木材生物质高效液化条件的选择及液化产物制备化学品和生物燃油给予理论基础与应用支持，促进了生物质资源的有效转化利用及其生物质基产品的开发。     

近红外光谱结合共识模型快速检测果酒的总酚含量

果酒发酵中的多酚是引起果酒口感、颜色变化的重要因素。为保证果酒品质,有必要开发一种快速监测发酵过程中多酚含量变化的技术。收集不同批次成熟期的蓝莓、桑葚为原料,分别碾压成汁,同时按比例混合二者,于小型发酵罐进行发酵。通过离线收集不同发酵时段的发酵液于离心管,高速离心后取上清液置于棕色瓶保存,共计得到48个果酒发酵样本。将上清液置于三个平行样比色皿,以傅里叶快速变换近红外光谱仪(FT-NIR)采集其透射光谱,取平均值作为该样本的光谱信号。然后将棕色瓶内的发酵液以国标法(即以标准液的吸光度值制定标准曲线)测定各样品的总酚含量,以duplex法计算样本光谱之间的距离且按2∶1的比例划分为训练集和预测集。采用间隔偏最小二乘法(iPLS)将训练集样本的透射光谱与总酚含量之间构建定量模型,间隔数从2依次变化到60个。该研究创新之处是使用共识方法融合多个已构建好的iPLS成员模型,按一定的共识规则分配权系数。通过各成员模型交互验证的残差及其残差之间的相关性来优化各成员模型的线性组合,以拉格朗日乘数法求解各成员模型的权系数,使间隔偏最小二乘-共识模型(consensual iPLS,CiPLS)的交互验证均方根误差最小。相比于全局PLS模型、划分不同间隔数量时的iPLS模型,CiPLS均具有较小的预测误差。当划分39个间隔时由三个iPLS成员模型(即14th,16th,18th)组成的共识模型误差最小为124.2,交互验证相关系数为0.944,对预测集样本的预测均方根误差为163.4,预测相关系数为0.931,预测性能均优于PLS和iPLS模型。另外,作为对比选用连续投影算法与无信息变量剔除法来优化光谱模型,其预测性能均不及本文提出的共识模型。分析各iPLS模型预测残差之间的相关性,发现共识模型主要是融合那些具有较高预测性能且模型间较低相关性的成员模型。结果表明,光谱分析结合共识方法可提高回归模型的预测精度、减少建模所需变量数,能够用于果酒总酚含量的离线快速检测。     

湿度对水泥生料近红外光谱检测的影响及补偿方法

近红外光谱检测已被应用于水泥生料成分的快速检测,但现场环境中的湿度等因素会对光谱产生干扰,从而降低检测精度。为了提高检测精度,在实验分析湿度对水泥生料近红外光谱检测影响的基础上研究了补偿方法。在水泥厂选取了24份水泥生料样本,其中18份作为校正集,6份作为验证集;水泥生料中的有效成分为SiO2,Al2O3,Fe2O3和CaCO3,各成分含量的标准值由X射线荧光光谱分析测出。首先,将校正集的18份样本每份重复装样测5次光谱,用得到的90个光谱建立模型Ⅰ;再每份样品制作5个湿度梯度样本,其获得过程为,先将样本放置在电加热平台上,用玻璃棒将样本摊平,180℃下加热30 min,再将样本放置在散热片上进行降温,待样品恢复室温后取出进行第一次光谱扫描,得到1个光谱,将测量后的样本放入搅拌器,使用装有去离子水的喷雾器对其喷雾两次,然后搅拌30 s混合均匀,测量混合后的样本得到下一个光谱,重复该过程,得到具有湿度梯度的5个光谱。所有样本均采用烘干法进行湿度测量,样本湿度变化区间在0.6%~2%以内。对每个湿度梯度的样本测量1次,用得到的这90个光谱建立模型Ⅱ。然后,将验证集的6份样本每份制作5个湿度梯度,获取方式与校正集相同,对每个湿度梯度的样本测量1次,得到30个光谱。所有光谱均采用多元散射校正预处理,拟合波段选择4000~5000 cm^-1,建模方法采用偏最小二乘法。比较同一份样本的5个湿度梯度,可以看到在5200 cm^-1处光谱差异最大,在其他位置也有肉眼可见的明显差异,因此,湿度变化对全波段光谱有明显的影响。最后,将这30个光谱输入模型Ⅰ与模型Ⅱ进行验证,并对比模型Ⅰ与模型Ⅱ的预测均方根误差RMSEP。模型Ⅱ中SiO2,Al2O3,Fe2O3和CaCO3的预测均方根误差RMSEP比模型Ⅰ分别减小了25%,31.3%,33.3%和25%。实验结果表明,水泥生料样本湿度对近红外光谱模型的预测结果具有一定的影响,采用具有湿度梯度的样本进行建模可有效降低湿度对预测结果的影响。     

Lanthanum trilactate: Vibrational spectroscopic study − infrared/Raman spectroscopy

In this study lanthanum trilactate was prepared by neutralization reaction of lactic acid and lanthanum oxide, purified and identified by X-ray powder diffraction. Infrared spectra (Mid-IR region 4000–650 cm⁻¹) and Raman spectra (Stokes region 4000–100 cm⁻¹) of the high quality crystalline samples have been recorded and presented for the first time. For comparison DFT calculations were performed using Gaussian 09 D.01 and agreement between predicted and measured spectral data has been achieved. Acquired information can be utilized for substance identification for example in various industrial applications or in biological systems.     

Monitoring of the shrinkage during the photopolymerization of acrylates using hyphenated photorheometry/near‐infrared spectroscopy

This article describes a new method for the quantitative determination and time‐resolved monitoring of the polymerization shrinkage during ultraviolet (UV) photopolymerization. It is based on rheometry using a modified oscillating rheometer. Shrinkage is determined from the decrease of the gap between the rheometer plates. Moreover, near‐infrared (NIR) spectra can be recorded directly in the rheometer, which allows continuous determination of the conversion at any time of a shrinkage measurement. As both shrinkage and conversion data come from the same experiment, shrinkage can be analyzed in dependence on the current conversion achieved during UV irradiation, which enables direct investigation of correlations between both parameters. Hyphenated photorheometry/FT‐NIR spectroscopy was used for the determination of the polymerization shrinkage of pure acrylate monomers and oligomers as well as acrylate‐based formulations. Quantitative shrinkage values were found to be in excellent correlation with data that were determined by an independent method (via buoyancy measurements) and data from literature. Furthermore, the effect of ambient and irradiation conditions or the content of nanoparticles on the degree of shrinkage was studied. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 729–739     

Miscible blends of poly(ethylene oxide) with brush copolymers of poly(vinyl alcohol)‐graft‐poly(l‐lactide)

Even though poly(ethylene oxide) (PEO) is immiscible with both poly(l ‐lactide) (PLLA) and poly(vinyl alcohol) (PVA), this article shows a working route to obtain miscible blends based on these polymers. The miscibility of these polymers has been analyzed using the solubility parameter approach to choose the proper ratios of the constituents of the blend. Then, PVA has been grafted with l ‐lactide (LLA) through ring‐opening polymerization to obtain a poly(vinyl alcohol)‐graft‐poly(l ‐lactide) (PVA‐g‐PLLA) brush copolymer with 82 mol % LLA according to ¹H and ¹³C NMR spectroscopies. PEO has been blended with the PVA‐g‐PLLA brush copolymer and the miscibility of the system has been analyzed by DSC, FTIR, OM, and SEM. The particular architecture of the blends results in DSC traces lacking clearly distinguishable glass transitions that have been explained considering self‐concentration effects (Lodge and McLeish) and the associated concentration fluctuations. Fortunately, the FTIR analysis is conclusive regarding the miscibility and the specific interactions in these systems. Melting point depression analysis suggests that interactions of intermediate strength and PLOM and SEM reveal homogeneous morphologies for the PEO/PVA‐g‐PLLA blends. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1217–1226