分光光度法测定三氧化铀中的硫酸根

采用TBP-萃淋树脂吸附三氧化铀样品中的铀,硫酸根与铬酸钡进行交换反应后,直接比色法测定硫酸根的含量。实验中研究了三氧化铀样品中硫酸根含量测定的样品制备、分离、反应酸度,煮沸时间,铬酸钡用量等影响因素。优化条件下,采用硝酸(5mol/L)淋洗、1mL HCl溶液(2.5mol/L)调节溶液中酸浓度、使用2mL BaCrO_4进行交换反应、煮沸3min,得到方法相对标准偏差小于10%,加标回收率为92.9%～110%。实验结果表明,直接显色的测定方法灵敏、快速、准确度高。方法测定条件易于获得,适于推广应用。     

Nano‐MoO3 for highly selective enrichment of polycyclic aromatic hydrocarbons in in‐tube solid‐phase microextraction

Nano‐molybdenum trioxide was prepared from nano‐molybdenum disulfide by simple firing in muffle furnace. Nano‐molybdenum trioxide was used as the extraction coating on the stainless steel wire. Four wires were filled in a polyetheretherketone tube to get an extraction tube. The tube was connected to the six‐port valve of a high performance liquid chromatograph, and the online analysis system was constructed. Extraction selectivity of the tube for different types of compounds, including polycyclic aromatic hydrocarbons, plasticizers, estrogens, anilines and neonicotinoids, was studied. Good enrichment ability for polycyclic aromatic hydrocarbons, but the extraction efficiency of others was not satisfactory. Using eight polycyclic aromatic hydrocarbons as the targets, an analytical method was established after optimizing main factors such as sampling volume, sampling rate, methanol content, and desorption time. The established method exhibited wide linear range to 0.016–20.00 μg/L and low limits of detection to 0.005 μg/L, and the enrichment factors can be up to 2443. The method was applied to the detection of trace polycyclic aromatic hydrocarbons in tap water and river water, and a good recovery was obtained. The tube showed good durability and chemical stability, and it still remained good extraction effect after more than 140 run.     

RAFM钢TIG焊和电子束焊疲劳性能实验和分析模拟

利用ANSYS 对低活化铁素体马氏体(RAFM)钢进行非熔化极气体保护焊(TIG 焊)与电子束焊的抗疲劳模拟分析，再利用SDS200 电液伺服疲劳试验机对TIG 焊和电子束焊的两种RAFM 钢试件进行实验。通过施加相同梯度负荷对TIG 焊和电子束焊试件进行焊缝的疲劳性能实验。与实验结果对比分析，结果显示电子束焊优于 TIG 焊，但在一定负载下可以用TIG 焊代替电子束焊。     

旋涂法制备WO3薄膜电致变色性能

"智能窗"大规模推广顺应可持续发展潮流,三氧化钨(WO_3)是生产"智能窗"的一种重要电致变色材料,但调控WO_3薄膜电致变色性能机制仍待进一步研究。采用旋涂法制备WO_3薄膜,重点研究了溶液浓度和旋涂次数对调控WO_3薄膜电致变色性能的影响。通过表面轮廓仪测量薄膜厚度,X射线衍射(XRD)测量薄膜结晶情况,原子力显微镜(AFM)和扫描电子显微镜(SEM)分析薄膜表面形貌,光谱仪测量薄膜初始态、着色态和褪色态的透射率。实验结果表明,随着溶液浓度增加(0. 2～1. 0 mol/L),薄膜厚度从9. 7 nm增加到33. 3 nm,透射率调制能力从0%提升到37. 0%;多次旋涂薄膜厚度线性增长,线性拟合优度(R~2)达0. 98,5次旋涂后透射率调制能力达51. 3%。改变溶液浓度和旋涂次数都是调控薄膜透射率调制能力的有效手段,精准调控薄膜透射率调制能力对设计不同应用场景的电致变色器件具有重大意义。     

自清洁功能的超疏水微/纳米结构铜网用于高效的分离油水

本文介绍了一种简便的方法制备n-十二烷基三甲氧基硅烷@三氧化钨包覆的超亲油超疏水的铜网.所制备的铜网显示了较为突出的超亲油和超疏水性能,该铜网的水接触角大约有154.39°,而油接触角接近于0°.实验利用了各种有机溶剂和水的混合物对所制备网膜进行分离性能测试,结果表明所得涂覆铜网的油水分离效率高达99.3V,并且水的通量大约为9962.3 L·h~(-1)·m~(-2).所制备的铜网具有良好的稳定性,经过10次分离循环后分离效率仍然保持在90%以上.由于三氧化钨优异的光催化降解性能,所制备铜网具有自清洁能力.因此,被润滑油污染的网膜可以恢复超疏水性,而这种自清洁性使所制网膜可以反复用于油水分离.     

Instantaneous work hardening behaviour of two-phase tungsten heavy alloys: a phenomenological approach

ABSTRACT

The present work describes a phenomenological approach to explain the instantaneous behaviour of tungsten heavy alloys (WHAs) in heat-treated and swaged conditions. The strengths and elongation values of heat-treated materials are lower and higher than those of the swaged samples respectively. The heat-treated materials exhibit two slopes in true stress–true plastic strain curves and follow the Ludwigson constitutive equation. On the other hand, swaged materials display a single slope and adhere to typical Swift constitutive equation. The latter reflect the presence of pre-strain in the materials due to swaging deformation. The fracture surfaces in heat-treated materials consist of W-W decohesion along with matrix rupture and W-cleavage, while swaged samples consist of mainly W-cleavage. Both the materials display three typical stages (I, II and III) of work hardening. The second derivatives of true stress–true plastic strain curves of these alloys exhibit a perfect parabola although the nature of true stress–true strain as well as true stress–true plastic strain curves is quite different in heat-treated and swaged materials. This has been observed for the first time in WHAs consisting of matrix and W-grains. The shape of the parabola is simple and easy to fit. The fitting parameters of parabolas have been successfully employed to explain the flow behaviour of a large number of tungsten heavy alloys having two-phase microstructure in different processing conditions.     

The Remarkably Robust,Photoactive Tungsten Iodide Cluster [W6I12(NCC6H5)2]

The new heteroleptic tungsten iodide cluster compound [W₆I₁₂(NCC₆H₅)₂] is presented. The synthesis is carried-out from Cs₂W₆I₁₄ and ZnI₂ under solvothermal conditions in benzonitrile solution, yielding red cube-shaped crystals. [W₆I₁₂(NCC₆H₅)₂] represents a heteroleptic [W₆I₈]-type cluster bearing four apical iodides and two benzonitrile ligands. Molecular [W₆I₁₂(NCC₆H₅)₂] clusters form a robust hydrogen bridged crystal structure with high thermal stability and high resistibility against hydrolysis. The electronic structure is analyzed by quantum chemical methods of the calculated electron localization function (ELF) and the band structure. Photoluminescence measurements are performed to verify and describe the photophysical properties of [W₆I₁₂(NCC₆H₅)₂]. Finally, the photocatalytic properties of [W₆I₁₂(NCC₆H₅)₂] are evaluated as a proof-of-concept.     

氧化钛负载脱硝催化剂的碱中毒过程：氧化钒的保留和氧化钨的牺牲

V2O5-WO3/TiO2催化剂目前已广泛用于电厂和工业锅炉燃烧废气脱硝,但燃烧原料煤及石油中含有的杂质元素碱金属与碱土金属元素可吸附在催化剂上,不仅会减少催化剂酸性位的数量,还会与催化活性元素结合生成惰性物种,导致催化剂失活。因此,已有许多有关钒钨钛催化剂碱中毒的研究,从催化剂的氧化还原能力、酸性位损失及表面孔结构等方面进行了讨论。但这些研究大多集中在碱中毒对活性组分V2O5的影响及中毒催化剂的活性变化,很少涉及催化剂中WO3的作用,也缺乏有关不同活性元素与钾盐反应的实验证据。本文采用过量浸渍法制备了不同钒和钨含量的钒钨钛催化剂,研究了氯化钾对其氨法选择性催化还原(NH3-SCR)活性的失活效应。利用感应耦合等离子体、N2吸附、拉曼光谱、H2程序升温还原、NH3吸附红外光谱和NH3氧化活性等手段对新鲜和中毒催化剂的性质进行了表征,特别探讨了V2O5和WO3对催化剂抗碱中毒能力的贡献。
　　催化剂活性测试结果表明, V2O5含量越高,活性温度窗口越宽,而且含有WO3的三元催化剂活性高于V2O5/TiO2二元催化剂。催化剂的BET比表面积和孔结构取决于TiO2载体,随活性组分配比变化不大,说明催化剂物理结构性质并非影响活性的主要因素。原位红外光谱及H2程序升温还原测试结果表明,随V2O5含量提高,催化剂表面Br?nsted酸性位数量及氧化还原能力提高。作为反应的主要活性物种, V2O5在碱中毒处理后变成惰性的偏钒酸钾KVO3,使催化剂中Br?nsted酸性位减少,热稳定性下降,并削弱了催化剂的氧化还原能力,因此低钒含量的催化剂容易严重中毒失活。在高钒负载量(3%)时,部分V2O5在碱中毒后得以保留,从而使催化剂保持了一定的脱硝催化活性。
　　另外, WO3能给催化剂表面提供热稳定的酸性位,虽然WO3自身的氧化还原能力差,但其能改善V2O5的分散性,从而提高V2O5-WO3/TiO2催化剂的活性。除此之外, WO3在催化剂碱中毒过程中还能扮演牺牲剂,与钾反应生成钨酸钾(K2WO4),即在V2O5与钾离子结合形成KVO3的同时,部分WO3也会与钾反应形成K2WO4,可以使三元催化剂保留更多的活性V物种。因此,在所研究的催化剂中,高钒负载量的V2O5-WO3/TiO2催化剂表现出最好的抗碱中毒能力。
　　活性影响因素分析表明,对于新鲜催化剂,其表面吸附的NH3量足够多,催化剂活性与表面酸性相关度不大,脱硝效率主要取决于催化剂的氧化还原能力。但是,对于碱中毒处理后的催化剂,其表面吸附NH3的能力大大削弱,这时脱硝效率除了受催化剂氧化还原能力影响,在很大程度上也依赖于催化剂的表面酸性。     

The electrochemical evaluation of antipsychotic drug (promethazine) in biological and environmental samples through samarium cobalt oxide nanoparticles

In this work, we developed a perovskite structured samarium cobalt oxide nanoparticles (SmCoO₃ NPs) with the aid of the co-precipitation method. The rare earth metal (Sm) and cobalt oxide combined to form a perovskite lattice structure. One-pot route synthesized SmCoO₃ NPs were scrutinized successfully through various physicochemical techniques. Concerning its effective thermal stability and electrical properties, the synthesized SmCoO₃ NPs have been effectively implemented in the electrochemical evaluation of promethazine hydrochloride (PHY) using cyclic voltammetry. The electrochemical detection of PHY was performed through SmCoO₃ NPs-modified glassy carbon electrode (GCE) and unmodified GCE. The electron transfer kinetics, effect of scan rate, the influence of pH, electroactive surface area, selectivity, and sensitivity have been studied. The electron charge transfer rate (R_ct) and electrolyte resistance (R_s) were calculated to be 105.59 (Ω) and 150 (Ω) in the ferricyanide probe, indicating great facilitation of the electron transfer between PHY and SmCoO₃ NPs deposited on the electrode surface. Further, the optimized SmCoO₃-modified GCE exemplifies excellent selectivity, storage stability, reproducibility, repeatability, detection limit (5 nM), sensitivity (0.594 μA μM^?1 cm^?2), and wide consecutive linear ranges, respectively. Besides, the proposed method has been effectively employed for the detection of PHY in the various real samples which reveals good recoveries of 95.40–99.17%.