石英晶体板非线性高频振动的拓展伽辽金法分析

针对考虑几何和材料非线性的石英晶体板厚度剪切振动和弯曲振动的方程组,利用扩展伽辽金法对该方程组进行转化和求解,分别获得了强烈耦合的厚度剪切振动模态和弯曲振动模态的频率响应关系,绘制了不同振幅比和不同驱动电压影响下的频率响应曲线图。数值计算结果表明可以选取石英晶片的最佳长厚比尺寸来避免两种模态的强烈耦合。驱动电压的变化将引起石英晶体谐振器厚度剪切振动频率的明显改变,必须将振动频率的漂移值控制在常用压电声波器件的允许值之内。扩展伽辽金法对石英晶体板非线性振动方程组的求解为非线性有限元分析和偏场效应分析奠定了基础。     

石墨基液流电池复合双极板

液流电池是一种安全性高、使用寿命长、可扩展的大规模储能系统,可以协助电网调峰储能,提高能源利用率,发展前景广阔。双极板是液流电池的重要组成部分。功能上起到了分隔、串联电池、传导电流、为电堆提供结构支撑等作用。从成本构成角度看,双极板的价格占电堆成本的比重也较大。开发高性能、低成本的双极板对加快液流电池的商业化应用具有重要意义,也是目前业界的迫切需求。虽然文献上报道了许多针对液流电池双极板开发的工作,但是目前高性能、低成本的液流电池双极板产品仍无法充分满足市场需求。本文着重介绍了石墨基复合双极板的研究现状,介绍了材料选择、工艺流程对关键性能的影响,对相关工作进行了评述,并为液流电池双极板的开发提出了建议。     

薄板结构加筋布局优化设计方法研究

提出一种两步优化策略，以加筋板结构的固有频率最大化为目标函数，以结构所受外载荷作用的最大静变形为约束条件，开展薄板结构加筋构件的布局优化设计研究。为了降低加筋布局优化的难度，提高优化设计的效率，将加筋等效为一系列弹性铰（点）支撑，以便快速获得加筋横向移动的灵敏度信息。在基本不改变结构重量的情形下，通过合理布局加筋位置，能显著改善结构的刚度分布，提高结构的整体承载能力。随后，小幅调整加筋的截面尺寸，以满足对结构最大变形的设计要求。最后，用两个算例验证了所提优化方法的可行性和有效性。     

Investigations of Viscous Dissipation in Stagnation Point Flow Past a Stretchable Riga Wall: Modern Analysis of Heat Transport

This article scrutinizes the features of viscous dissipation in the stagnation point flow past through a linearly stretched Riga wall by implementing Cattaneo-Christov heat flux model. Viscous dissipation is carried out in Cattaneo-Christov diffusion analysis for the first time in this letter. As a result of Cattaneo-Christov model, some extra terms of viscous dissipation are appeared in the energy equation. These extra terms of viscous dissipation are missing in the literature. On the utilization of suitable transformations, the equations governing the problem are reduced under the boundary layer approximation into the non-linear and dimensionless ordinary differential equations. Convergent approach is utilized to solve the dimensionless governing equations. The solution thus acquired is used to highlight the effects of emerging parameters on velocity distribution and fluid's temperature through the graphs. Features of the drag force (or skin friction co-efficient) are graphically interpreted. It is noticed that the presence of modified Hartman number helps to reduce the fluid's temperature but enhances the velocity profile. Further an enlargement in the value of thermal time relaxation parameter helps to decrease the temperature distribution.     

Natural convection heat transfer at reduced pressures

This paper experimentally studies the natural convection heat transfer characteristics on horizontal and vertical plates at pressures lower than atmospheric value. Eight different pressures ranging from 10Pa to 101.325kPa, and three heating loads were used in the experiments. It is found that natural convection heat transfer characteristics at reduced pressures are independent of the plate arrangements and present different behaviors in two pressure ranges, 10Pa < p < 1000Pa and p > 1000Pa. The experimental heat transfer results are correlated into a non-dimensional equation to help the thermal design of stratosphere aircrafts and airborne equipment.     

基于精化锯齿理论的功能梯度夹心微板静弯曲模型

基于精化锯齿理论和新修正偶应力理论,建立了能够准确预测功能梯度夹心微板挠度、位移和应力的静弯曲模型。为了描述微板不同方向上的尺度效应,将两个正交材料尺度参数引入本文模型。以受双向正弦载荷作用的简支板为例,探究了夹心微板弯曲行为中尺度效应对结构刚度的影响。算例结果表明,当微板几何参数与材料尺度参数接近时,基于本文模型所测微板的最大弯曲挠度、局部位移和应力均小于传统精化锯齿理论给出的结果,捕捉到了尺度效应;尺度效应随着微板几何尺寸的增大而逐渐减弱,当微板几何尺寸远大于材料尺度参数时,尺度效应消失。此外,板的跨厚比和功能梯度变化指数也会对尺度效应产生一定影响。     

An asymptotic Reissner–Mindlin plate model

A mathematical study via variational convergence of a periodic distribution of classical linearly elastic thin plates softly abutted together shows that it is not necessary to use a different continuum model nor to make constitutive symmetry hypothesis as starting points to deduce the Reissner–Mindlin plate model.     

Aeroelastic analysis of cantilever plates using Peters’ aerodynamic model,and the influence of choosing beam or plate theories as the structural model

In this paper, the aeroelastic analyses of a rectangular cantilever plate of varying aspect ratio is presented. The classical plate theory has been selected as the structural model. The main point that distinguishes this study from previously reported research is employing Peters’ theory to model aerodynamic effect which is not straightforward. The Peters’ aerodynamic model was originally developed to provide lift and moment, which is only applicable to the structural model based on the beam theories. In this study, using the basic concept of the Peters’ aerodynamic model in addition to utilizing the Fourier series, the pressure distribution is derived, which makes Peters’ model applicable to structural models based on plate theory. This combination provides a much simpler state–space aeroelastic model for plates in comparison to the prevalent panel methods, which could lead to a significant reduction in computational time. In addition, the aeroelastic response of the plate with respect to changes in the structural model from the beam theory to the plate theory is evaluated. By using data from an experiment carried out at Duke University, the theoretical results are evaluated. Furthermore, the differences in structural models obtained from the plate and beam theories can be divided into two distinct parts, which are responsible for differences in bending and torsional behaviors of the structure, separately. This approach enables us to measure the effects of differences of each behavior separately, which could provide with a new insight into the problem. It has been determined that the flutter speeds obtained from the beam and plate aeroelastic models are little affected by the difference in bending behavior, but rather is mainly caused by the difference in torsional frequencies.     

The recent progress of functionally graded CNT reinforced composites and structures

In the last decade,the functionally graded carbon nanotube reinforced composites(FG-CNTRCs)have attracted considerable interest due to their excellent mechanical properties,and the structures made of FG-CNTRCs have found broad potential applications in aerospace,civil and ocean engineering,automotive industry,and smart structures.Here we review the literature regarding the mechanical analysis of bulk CNTR nanocomposites and FG-CNTRC structures,aiming to provide a clear picture of the mechanical modeling and properties of FG-CNTRCs as well as their composite structures.The review is organized as follows:(1)a brief introduction to the functionally graded materials(FGM),CNTRCs and FG-CNTRCs;(2)a literature review of the mechanical modeling methodologies and properties of bulk CNTRCs;(3)a detailed discussion on the mechanical behaviors of FG-CNTRCs;and(4)conclusions together with a suggestion of future research trends.     

受限亚音速气流中倒置悬臂壁板静气弹稳定性的理论及实验研究

板壳结构在航空航天、高速列车、能量采集等诸多工程领域已经得到了广泛应用. 将悬臂壁板倒置于轴向气流中并在壁板周围流场中设置刚性壁面可有效地调控壁板的失稳速度, 是俘能器优化设计的重要措施之一. 但针对刚性壁面作用下亚音速气流中倒置悬臂壁板的失稳机制仍需要开展深入研究. 本文以受限亚音速气流中倒置的二维悬臂壁板为对象, 以理论分析及风洞实验为手段, 研究了单侧刚性壁面效应对倒置悬臂壁板静态失稳特性的影响规律. 在理论分析中, 首先应用镜像函数法来处理壁面约束条件, 基于算子理论研究获得了以Possio积分方程为表征的壁板气动力, 壁面效应实际表征为一包含移位Tricomi算子的复合算子; 然后将壁板失稳方程的求解问题转化为定区间上的函数逼近问题; 最后, 依据Wererstrass定理并利用最小二乘法求解该最优函数, 以获得系统的失稳临界参数. 在试验研究中依据压杆稳定原理设计了壁板静态失稳的测试方法并完成了风洞实验. 理论分析结果表明, 壁板会发生发散(静气动弹性)失稳, 临界动压随壁板与壁面间距的增加而增大并最终趋于稳定(无壁面情况); 通过理论与风洞实验结果的对比分析, 验证了本文气动力及理论分析的适用性及准确性. 针对倒置悬臂壁板结构的气动弹性失稳问题, 本文提出的方法不涉及系统方程的离散及特征值求解问题, 而是将其转化为了定区间上的函数逼近问题进行求解, 这为弹性结构静气动弹性失稳问题的研究提供了一个可行的新思路.