Experimental investigation on tunnel sonic boom

Upon the entrance of a high-speed train into a relatively long train tunnel, compression waves are generated in front of the train. These compression waves subsequently coalesce into a weak shock wave so that a unpleasant sonic boom is emitted from the tunnel exit. In order to investigate the generation of the weak shock wave in train tunnels and the emission of the resulting sonic boom from the train tunnel exit and to search for methods for the reduction of these sonic booms, a 1300 scaled train tunnel simulator was constructed and simulation experiments were carried out using this facility.In the train tunnel simulator, an 18 mm dia. and 200 mm long plastic piston moves along a 40 mm dia. and 25 m long test section with speed ranging from 60 to 100 m/s. The tunnel simulator was tilted 8° to the floor so that the attenuation of the piston speed was not more than 10 % of its entrance speed. Pressure measurements along the tunnel simulator and holographic interferometric optical flow visualization of weak shock waves in the tunnel simulator clearly showed that compression waves, with propagation, coalesced into a weak shock wave. Although, for reduction of the sonic boom in prototype train tunnels, the installation of a hood at the entrance of the tunnels was known to be useful for their suppression, this effect was confirmed in the present experiment and found to be effective particularly for low piston speeds. The installation of a partially perforated wall at the exit of the tunnel simulator was found to smear pressure gradients at the shock. This effect is significant for higher piston speeds. Throughout the series of train tunnel simulator experiments, the combination of both the entrance hood and the perforated wall significantly reduces shock overpressures for piston speeds ofu _p ranging from 60 to 100 m/s. These experimental findings were then applied to a real train tunnel and good agreement was obtained between the tunnel simulator result and the real tunnel measurements.     

Thermographic signal reconstruction for vibrothermography

Vibrothermography, also known as thermosonics or sonic infrared, is a method of nondestructive evaluation that finds cracks or delaminations from the heat given off in response to vibration. In vibrothermography, finding cracks requires identifying and localizing pulsed surface and subsurface heat sources from a time sequence of infrared images. Traditionally this identification involves manually stepping through and studying the images. Careful observation of the heating and subsequent cooling is needed to distinguish cracks from false indications. In this paper, we present an algorithm that reduces the entire time sequence to a single static plot. The plot uses only a few coefficients per pixel to reconstruct the original sequence; this is possible because the reduction is based on a physical model. As an added bonus, the algorithm reduces noise and improves sensitivity. A single false-color image summarizes all the information from the entire sequence, simplifying the task of identifying cracks.     

糠酸甲酯的清洁生产工艺

羧酸糠醇酯在国内是一类新型的、用途较广的食用香料,最早在天然咖啡的香气中发现,是重要的咖啡香气成分之一.     

Sonic spray ionization interface for liquid chromatography-mass spectrometry

A sonic spray ionization (SSI) interface for liquid chromatography-mass spectrometry (LC-MS) analysis was optimized for analysis of 2-[(1R)-3-[bis(1-methylethyl)amino]-1-phenylpropyl]-4-methyl-phenol (tolterodine), used as a model drug substance, and the influence of different parameter settings was evaluated using factorial design. A comparison between SSI and electrospray ionization (ESI) was made for tolterodine, tolterodine metabolites, and a set of steroids.SSI was found to give slightly poorer repeatability and broader peaks for tolterodine compared to ESI. However, there was no significant difference in chromatographic peak shape, and the repeatability using SSI was similar to that obtained using ESI if a ratio (area of tolterodine/area of metabolite) was used. In this study, the sensitivity was higher using SSI. For the analysis of pregnanolone, less water loss was obtained using SSI, probably due to less energy being transferred to the analyte upon ionization.     

光纤激光经过模清洁器后的强度噪声分析

对1560 nm单频光纤激光光源通过一个光学模清洁器后的强度噪声进行了分析研究.实验观察到模清洁器虽然对于激光的高频强度噪声有明显的抑制作用,但强度噪声特性随频率呈一定周期变化,且在低频处模清洁器对强度噪声有放大作用.本文认为这是由于模清洁器具有类似于光纤延迟线的时延效应,将激光源的部分相位噪声转化为强度噪声.通过理论分析,由相位噪声转化的相对强度噪声幅度与激光相干时间、模清洁器的平均延时参数以及分析频率相关.分析结果与实验测量结果符合良好.此外,通过在光路中加入声光调制器进行反馈调制,激光的线宽从26 kHz压窄至16 kHz,模清洁器的锁定质量明显提高,经过模清洁器后的激光强度噪声有所减小,与理论相符.该结果进一步证实了由相位噪声转化而来的强度噪声与模清洁器的锁定质量无直接关系.通过该研究,完善了光学模清洁器对激光的噪声抑制模型.     

Shape-optimal design of graded index sonic crystal formations using natural cubic splines

Noise reduction through upward refraction can be achieved by artificial means, using a graded index sonic crystal. In addition to upward refraction, it will be shown that these periodically spaced cylinder formations can simultaneously benefit from band-gap phenomena. The aim of this paper is to present a method to optimise the broadband noise reducing performance of graded index sonic crystals, in a frequency range from well below to well above the lowest band-gap frequency. A design technique based on the creation of complex cylinder formations has been explored, in which the effective propagation speed is spatially varied using natural cubic splines. Sets of complex barrier shapes are compactly described by re-locating a number of control points in a two-dimensional cartesian plane and connecting the control points by (curved) line segments. In addition to the cluster shape, a complex graded index sonic crystal structure was formed by varying the lattice constant and the cylinder radius, where the cylinder radius was varied as a function of height. All these parameters were optimised with a multi-objective genetic algorithm, for structures based on horizontally oriented acoustically hard cylinders, located above a perfectly reflecting ground plane. A four-lane outdoor situation, with a traffic scenario consisting of 95% light and 5% heavy duty vehicles driving at 70 km/h has been studied in a two-dimensional domain. For such a configuration we obtained a spatially averaged mean reduction of 4.2–5.3 dBA, with structures covering an effective cross-sectional area of 1 m². It was found that the insertion loss among the studied traffic lanes was reasonably constant. In addition, it was found that the low-frequency performance of the studied structures is enhanced by incrementing the barrier-height while increasing the number of scatterers as a function of height.     

清洁生产——环境战略的新认识

清洁生产自80 年代末在美国等发达国家提出以后, 得到国际社会的普遍响应, 成为一种环保潮流, 被认为是环境战略由被动反应转向主动行动的一个转折点。污染控制系统具有很大的局限性, 不仅消耗了大量能源和资源, 而且无法解决目前面临的全球性环境问题; 清洁生产强调源削减, 比较好地解决了经济和环境持续、协调发展问题。本文系统地介绍了清洁生产的起源和发展, 通过与污染控制系统的对比, 论述清洁生产战略的重要意义。     

超声喷雾电离源的研制与表征

研制了超声喷雾电离源(SSI)。采用核糖核酸A、溶菌酶等样品和商品化的线性离子阱质谱仪对该电离源进行了表征。实验发现,对于生物大分子,超声喷雾电离质谱(SSI-MS)能够获得与电喷雾质谱(ESI-MS)类似的多电荷离子。但与同等条件下ESI-MS所获得的谱图相比,SSI主要获得低价态的多电荷离子。在此基础上,系统考察了SSI-MS各主要操作参数对不同价态蛋白质多电荷离子信号强度的影响,并提出了SSI离子化的可能机理。结果表明,在喷雾气压3.4~3.6 MPa、喷雾口到质谱入口的距离4~6 mm、离子传输管温度250~300℃、样液流速50~100μL/min、2%~5%甲酸酸性且不含甲醇的条件下,各价态蛋白质离子信号强度及信号分布均达到最优;而离子传输管温度越高,喷雾压力越大或溶剂中甲醇等挥发性成分越高,则越有利于低价态离子的形成。     

几种值得注意的有机原料清洁工艺技术

本文综述了基本有机原料生产中的几种清洁生产工艺。这些工艺, 或是显著提高目的产物的选择性, 从而不排放或少排放有害污染物; 或在生产过程中不用有害的或有污染的原料、催化剂和溶剂。文章也介绍了中国石油化工总公司在该领域的研究开发工作。     

聚苯硫醚纤维的抗张强度与工艺和结构的关系

以熔融纺丝法制备出不同结晶度的各向同性聚苯硫醚纤维作为样品,根据密度和声速测定值确定出PPS晶相和无定形相的本征横向声模量E0⊥,c(4.40 GPa)和E0⊥,am(1.99 GPa).利用密度梯度法测定出的结晶度Xc和X-衍射法测定的晶区取向因子fc,按照Samules模型计算出不同牵伸和定型工艺下制备的PPS纤维样品的非晶区取向因子(fam),在此基础上分析PPS纤维抗张强度与牵伸定型工艺参数、结构之间的关系.结果表明,PPS纤维的最佳牵伸温度及紧张热定型温度分别在90℃和190℃附近;提高PPS纤维的牵伸温度及紧张热定型温度可以增加纤维的结晶度,在一定范围内对纤维抗张强度的增加有促进作用;但较高的牵伸温度及紧张热定型温度不利于纤维非晶区取向的提高,造成PPS纤维抗张强度降低.牵伸倍数的增加可以有效提高PPS纤维的非晶区取向程度,抗张强度也随着增加.