高居里温度铁电单晶PIN-PT的机电性能

弛豫铁电单晶Pb(In_1/2Nb_1/2)O₃-PbTiO₃(PIN-PT)相较于常用的Pb(Mg_1/3Nb_2/3)O₃-PbTiO₃(PMN-PT)具有更高的居里温度,在高稳定性、高性能的传感器、换能器方面具有应用前景。本工作采用谐振法研究了[001]方向极化的0.66PIN-0.34PT铁电单晶的全矩阵机电性能参数。0.66PIN-0.34PT 单晶的三方-四方相变温度(T_RT)约为160 ℃,居里温度(T_C)约为260 ℃,室温压电系数d₃₃、d₃₁、d₁₅分别为1 340 pC/N、-780 pC/N、321 pC/N,介电常数ε^T₃₃、ε^S₃₃、ε^T₁₁、ε^S₁₁分别为2 700、905、2 210、1 927,机电耦合系数 k₃₃、k₃₁、k₁₅、k_t分别为 87%、58%、38%、61%。其纵向压电常数(d₃₃)和纵向机电耦合系数(k₃₃)小于 PMN-PT 单晶,但是横向压电性能(d₃₁)和剪切压电性能(d₁₅)都略高于PMN-PT单晶。另外,研究了机电耦合性能随温度的变化趋势,发现0.66PIN-0.34PT单晶在150 ℃以下有较好的温度稳定性。     

Electronic structures of CO adsorbed Pt-skin surface on Pt–Co and Pt–Ni alloys

By using angle resolved photoemission spectroscopy, we investigate the electronic structures of Pt-skin layer of Pt–Co and Pt–Ni alloys with CO molecules on the surface. Measured Fermi surface maps and band dispersions reflect the signatures of chemical bonding between Pt-skin layer and CO molecules. Furthermore, the degree of chemical bonding strength of CO molecules, estimated from the energy shift of the participating bands, is found to be reduced on both Pt bimetallic alloys. Our results show how the surface band structure of Pt bimetallic alloys is modified with molecular orbitals of CO molecules on the surface, revealing the important role of the electronic structure in the determination of chemical properties of bimetallic alloys.     

Using a Novel and Easy-to-Use Sandwich Structure Device to Evaluate the Cooling Properties of Cool Materials

A number of cool materials have been designed and used in hot weather to minimize the heat coming from sunlight. Traditionally, solar reflectance and infrared emittance were measured to characterize the cooling properties of cool materials. However, these methods could represent the cooling property only indirectly. In this work, a sandwich structure device that can straightforwardly measure the cooling properties of cool materials was designed. Two cool materials, including high-density polyethylene (HDPE) and polyvinyl chloride (PVC), were selected to verify the device. For the purpose of comparison, UV-vis-NIR spectral characterization was also used to evaluate the cooling properties of the selected materials. The results, especially for the HDPE/Green 260 composite sample, which presents much lower solar reflectance but better cooling property, indicated that the cooling properties cannot be entirely represented by only the reflectance or transmittance, and the sandwich structure device was able to make up for this deficiency.     

宽体液腔Janus-Helmholtz换能器

本文使用有限元方法对宽体液腔Janus-Helmholtz(JH)换能器进行了仿真分析,得出了壳体宽度拓展增量对JH换能器工作性能的影响规律。使用三维建模的方式,分析了连接部分对换能器性能的影响及宽体壳体的的模态,证明了三维建模的必要性。依据仿真优化结构设计了一款宽体液腔JH换能器并进行了湖上测试。最终测试结果与仿真结果有很好的一致性,相较直筒JH换能器其谐振频率降低300Hz,发射电压响应最高可达144dB。     

基于有序介孔碳的氯离子选择性电极的制备及其在手持传感系统中的应用

以有序介孔碳(OMC)球为离子-电子转换层,制备了固态氯离子选择性电极,构建了基于离子敏感的场效应晶体管(ISFET)的手持式传感系统,用于检测人体血清中的氯离子。优化了OMC前驱体的碳化温度,探究了OMC形貌结构对电极传感性能的影响;电极柔性化制备后考察了其在手持系统中对氯离子的检测效果。结果表明,最优条件下,电极在5.12×10^-4~1.02 mol/L的浓度范围呈现线性响应,响应斜率为60 mV/decade。该柔性电极在手持传感系统中展现出高灵敏度和重现性,可用于人体血清样品中氯离子的检测,其回收率为96.3%~104.9%。     

压电式微滴按需喷射的过程控制和规律

微滴喷射增材制造技术中沉积微滴的大小与均匀性是影响成型件质量的关键因素.本文设计了一种用于生成均匀微滴的压电驱动式微滴喷射装置,通过压电材料带动柔性膜片振动,将液体从喷嘴中喷出生成微滴,采用数值模拟和实验相结合的方法,研究了不同控制参数下膜片振幅及其对生成微滴尺寸和均匀性的影响.研究结果表明:膜片振幅大小受到驱动电压和压电频率的共同影响,压电频率是导致膜片中心点振幅实验测量值小于理论计算值的主要原因,膜片振动会导致喷嘴内部压力发生变化从而影响微滴生成尺寸.在相同驱动电压条件下,压电频率为10 Hz时存在压电膜片振幅最大值.随着膜片振幅的增大,喷孔处液体速度和液柱长度增大到临界值时可以生成微滴,当喷孔处的液柱长度超过临界值时,会形成卫星液滴. 当膜片振幅区间在30 $\mu$m$\sim $42 $\mu $m可以稳定生成微滴,生成最小微滴尺寸为339.8$\mu$m,直径最大变化率为0.29%,相邻两微滴间距最大变化率为2.67%,生成微滴的尺寸及均匀性较好.研究结果有助于提高压电式微滴喷射装置的液滴生成质量.      

4D Printing based piezoelectric composite for medical applications

Additive manufacturing (AM), otherwise known as three‐dimensional (3D) printing, is driving major innovations in many areas, such as engineering, manufacturing, art, education, and medicine. Although a considerable amount of progress has been made in this field, additional research work is required to overcome various remaining challenges. Recently, one of the actively researched areas lies in the AM of smart materials and structures. Electroactive materials incorporated in 3D printing have given birth to 4D printing, where 3D printed structures can perform as actuating and/or sensing systems, making it possible to deliver electrical signals under external mechanical stimuli and vice versa. In this paper, we present a lightweight, low cost piezoelectric material based on the dispersion of inorganic ferroelectric submicron particles in a polymer matrix. We report on how the proposed material is compatible with the AM process. Finally, we discuss its potential applications for healthcare, especially in smart implants prostheses. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2019 , 57, 109–115     

A Semiconducting Organic–Inorganic Hybrid Perovskite‐type Non‐ferroelectric Piezoelectric with Excellent Piezoelectricity

Piezoelectric materials are a class of important functional materials applied in high‐voltage sources, sensors, vibration reducers, actuators, motors, and so on. Herein, [(CH₃)₃S]₃[Bi₂Br₉]( 1 ) is a brilliant semiconducting organic–inorganic hybrid perovskite‐type non‐ferroelectric piezoelectric with excellent piezoelectricity. Strikingly, the value of the piezoelectric coefficient d₃₃ is estimated as ≈18 pC N^?1. Such a large piezoelectric coefficient in non‐ferroelectric piezoelectric has been scarcely reported and is comparable with those of typically one‐composition non‐ferroelectric piezoelectrics such as ZnO (3pC N^?1) and much greater than those of most known typical materials. In addition, 1 exhibits semiconducting behavior with an optical band gap of ≈2.58 eV that is lower than the reported value of 3.37 eV for ZnO. This discovery opens a new avenue to exploit molecular non‐ferroelectric piezoelectric and should stimulate further exploration of non‐ferroelectric piezoelectric due to their high stability and low loss characteristics.     

Properties of cat-eye modulating retro-reflector and its application with piezoelectric transducer

Piezoelectric cat-eye modulating retro-reflector (MRR) is the core component of an acousto-optic retro-identification system. The influence of the optical parameters (link distance l, lens focal length f and the detector diameter r) to the cat-eye effect was analyzed theoretically and experimentally. A piezoelectric cat-eye retro-identification (PCERI) system was built, and an information transmission ratio of 2 kHz was achieved which can satisfy an access control system.