密度泛函理论方法研究填料表面对聚合物摩擦化学的影响

采用超声分散法制备出氧化铝、高岭土、氧化硅/聚四氟乙烯复合材料, 使用线性往复摩擦磨损试验机对比三种复合材料的摩擦学性能. 结果表明 质量分数10%的氧化铝、高岭土能将聚四氟乙烯的磨损率降低约4个数量级, 而氧化硅仅能降低约3个数量级. 对金属对偶表面形成的转移膜的形貌和化学成分进行分析发现 氧化铝、高岭土/聚四氟乙烯在金属对偶面上形成了高度羧酸盐化的转移膜. 用密度泛函理论对三种填料表面上碳氟分子吸附过程进行模拟, 结果显示氧化铝、高岭土表面的路易斯酸性位点促进了碳氟分子的脱氟过程, 产生了更多的羧酸螯合物的中间产物; 氧化硅缺少路易斯酸性位点, 因此不能促进高度羧酸盐化的转移膜形成.     

Controlling thermomechanical behavior of semicrystalline hydrogenated polynorbornene through the cis- to trans-cyclopentylene ratio

Though polynorbornene synthesized by ring-opening metathesis polymerization has an intrinsically all-cis configuration of the cyclopentylene backbone rings, a fraction of these rings can be epimerized to the trans configuration during hydrogenation over suitable catalysts. By varying the method of hydrogenation, semicrystalline hydrogenated polynorbornenes (hPNs) with trans levels between 0 and 36% were obtained. With increasing trans content, the glass transition temperature, melting point, and enthalpy of melting decrease modestly. By contrast, the temperature at which the hPN crystal transitions into a rotationally disordered polymorph varies strongly with trans content, ranging from 126 °C (all-cis) to 71 °C at 27% trans; at trans contents of 34% and above, no rotationally-ordered phase is observed at any temperature. The room-temperature Young's modulus shows no dependence on trans content, while the yield stress drops by 20% at 1% trans content and slowly decreases further with additional epimerization. The temperature dependence of the Young's modulus differs for trans-containing versus all-cis polymers, while the temperature dependence of the yield stress is set by the polymorph type (rotationally ordered vs. disordered).     

Spectroscopic properties and bond dissociation energies of PbX,PbX±, PbX2 and PbX2± (X ​= ​F,Cl, Br,I)

Ab initio calculations have been performed to investigate some of the spectroscopic properties, like geometry, frequency, electron affinity, ionization potential and finally adiabatic bond dissociation energies (BDEs) of lead monohalides, lead dihalides and their ions viz. PbX, PbX^±, PbX₂, $\mathrm{P}\mathrm{b}{\mathrm{X}}_{\mathrm{2}}^{\pm }$ (X ?= ?F, Cl, Br, I) in their ground state at the QCISD(T)//MP2 level of theory using correlation consistent basis sets. For the validation of MP2 optimized geometry and frequency, we further obtained geometry and frequency of all the neutral and ionic systems using QCISD(T) method with the same basis sets. The BDEs of PbX₂ molecules are calculated using the BDEs of $\mathrm{P}\mathrm{b}{\mathrm{X}}_{\mathrm{2}}^{\pm }$ ions and taking ionization potential and electron affinity of various systems. The calculated values are found in good agreement with the available data. Most of the data for ionic systems are reported first time in literature.     

Lanthanide SMMs Based on Belt Macrocycles: Recent Advances and General Trends

Enhancement of axial magnetic anisotropy is the central objective to push forward the performance of Single-Molecule Magnet (SMM) complexes. In the case of mononuclear lanthanide complexes, the chemical environment around the paramagnetic ion must be tuned to place strongly interacting ligands along either the axial positions or the equatorial plane, depending on the oblate or prolate preference of the selected lanthanide. One classical strategy to achieve a precise chemical environment for a metal centre is using highly structured, chelating ligands. A natural approach for axial-equatorial control is the employment of macrocycles acting in a belt conformation, providing the equatorial coordination environment, and leaving room for axial ligands. In this review, we present a survey of SMMs based on the macrocycle belt motif. Literature systems are divided in three families (crown ether, Schiff-base and metallacrown) and their general properties in terms of structural stability and SMM performance are briefly discussed.     

Insights into MWCNTs/polyimide nanocomposites: from synthesis to application as free-standing flexible electrodes in low-cost micro-supercapacitors

In the pursuit to enlarge the library of polyimide materials for energy applications, new polyimide/MWCNTs composite films have been developed by MWCNTs-assisted polycondensation reaction of a hydroxyl and triphenylmethane-containing diamine with benzophenone tetracarboxylic dianhydride targeting to highlight their electrical storage capability as flexible electrodes in micro-supercapacitors (mSCs). The Fourier-transform infrared spectroscopy, proton nuclear magnetic resonance, UV–vis, fluorescence, and Raman spectroscopies were used to demonstrate the evolution of interfacial interactions between MWCNTs and the precursors (diamine monomer and intermediate polyamidic acid) and polyimide matrix that proved to be the origin of MWCNTs homogeneous dispersion. Thus, composite films incorporating 1, 3, 5, and 10 w.t.% MWCNTs were obtained and thoroughly investigated with regard to their morphology, mechanical behavior, thermal stability, and electrical conductivity. The electrochemical performance of these composites was first analyzed in a classical three-electrode cell by cyclic voltammetry and galvanostatic charge-discharge in both aqueous and organic electrolyte systems. By far, the best electrical storage capacity was obtained with the composite polyimide film containing 10% MWCNTs that was further used as both active material and current collector in a flexible symmetric mSC realized by a straightforward and low-cost procedure. In the attempt to better exploit the advantages of this composite film, it was layered with a graphite-containing paint and tested as an electrode in a flexible mSC, which provided satisfactory results. To our knowledge, this is the first report on the electrical charge storage capability of a polyimide/MWCNTs free-standing film as a flexible electrode in mSCs, which do not require time- and resource-consuming processing steps.     

Enhanced thermal conductivity and mechanical properties of polymeric composites through formation of covalent bonds between boron nitride and rubber chains

Hexagonal boron nitride (BN) platelets, also known as white graphite, are often used to improve the thermal conductivities of polymeric matrices. Due to the poor interfacial compatibility between BN platelets and polymeric matrices, in this study, polyrhodanine (PRd) was used to modify BN platelets and prepared functionalized BN-PRd platelets, thereby enhancing the interfacial interaction between the thermal conductive filler and polymeric matrix. Then, BN-PRd platelets were dispersed into the nitrile butadiene rubber (NBR) matrix to yield high thermally conductive composites. The presence of N? C═S groups in PRd allowed the combination of PRd and NBR chains containing stable covalent bonds via vulcanization reaction. The thermal conductivity of the as-prepared 30 vol% BN-PRd/NBR composite reached 0.40 W/mK, representing an increment of 135% over pure NBR (0.17 W/mK). In addition, the largest tensile strength of NBR composite containing 30 vol% BN-PRd platelets was 880% times of pure NBR. The 30 vol% BN-PRd/NBR composite also displayed a relatively high dielectric constant (9.35 at 100 Hz) and a low dielectric loss tangent value (0.07 at 100 Hz), indicating their usefulness as dielectric flexible materials of microelectronics. In sum, the simplicity and good efficiency of formation of covalent bonds between boron nitride and rubber chains look very promising for large-scale industrial production of high thermally conductive composites.     

Rh(III)-Catalyzed One-Step Synthesis of ortho-Alkynylated Perylene Imide Dyes: Optical and Electrochemical Properties of New Derivatives

A one-step Rh-catalyzed site-selective ortho-C−H alkynylation of perylene as well as naphthalene mono- and diimides is reported. A single step regioselective access to ortho-C−H alkynylated derivatives of these ryleneimides not only increases the step economy of the ortho-functionalization on these dyes but also provides a quick access route towards highly functionalized dyes that have potential optoelectronic applications. Increased solubility of tetra(triisopropylsilyl)acetylenyl PDIs in organic solvents greatly enhances their utility for further derivatization.