化学类拔尖学生培养与高校青年教师成长协同发展实践*

在高等教育大众化的背景下,通过教学改革培养高素质的拔尖人才已显得非常重要。介绍一种以新入职的青年教师为实施主体的“理论课助教+实验课教学+科研训练”相结合的教学形式。通过连续、跟踪式的教学,不但可以选拔、培养出拔尖的化学类本科生,而且能够促进新入职的青年教师快速成长进步,起到“教学相长”的作用。     

线上线下混合式实验教学模式的改革与探索

大学化学实验课程是培养材料、化学、化工等专业人才应用基本操作和理论解决实际问题的综合性实践训练环节。文章探讨了当前大学化学实验发展由于受到仪器设备大型化、专业化、成本大、更新快等因素限制出现瓶颈,设计了线上线下混合实验教学模式,进行相应的软硬件建设,并开展线上线下混合式实验教学模式的改革与探索。该教学模式具有良好的教学效果,并且可复制可推广,为创新人才的培养和实验教学的创新提供了有益的借鉴。     

Coupling characteristics of laterally coupled gratings with slots

Laterally-coupled ridge-waveguide distributed feedback lasers fabricated without epitaxial regrowth steps have the advantages of process simplification and low cost. We present a laterally coupled grating with slots. The slots etched between the ridge and grating area are designed to suppress the lateral diffusion of carriers and to reduce the influence of the aspect-ratio-dependent-etching effect on the grating morphology in the etching process. Moreover, the grating height in this structure can be decreased to lower the aspect ratio significantly, which is advantageous over the conventional laterally coupled ridge waveguide gratings. The effects of five main structural parameters on the coupling characteristics of gratings are studied by MODE Solutions. It is found that varying the lateral width of the grating can be used as an effective way to tune the coupling strength; narrow slots (100 nm and 300 nm) and wide ridge (2 μm-4 μm) promote the stability of grating coupling coefficient and device performance. It is important to note that the grating bottom should be fabricated precisely. The comparative study of carrier distribution and mode field distribution shows that the introduction of narrow slots can strengthen the competitive advantage and stability of the fundamental mode.     

Asymmetric nonlinear-mode-conversion in an optical waveguide withPT symmetry

Asymmetric mode transformation in waveguide is of great significance for on-chip integrated devices with one-way effect, while it is challenging to achieve asymmetric nonlinear-mode-conversion (NMC) due to the limitations imposed by phase-matching. In this work, we theoretically proposed a new scheme for realizing asymmetric NMC by combining frequency-doubling process and periodic PT symmetric modulation in an optical waveguide. By engineering the one-way momentum from PT symmetric modulation, we have demonstrated the unidirectional conversion from pump to second harmonic with desired guided modes. Our findings offer new opportunities for manipulating nonlinear optical fields with PT symmetry, which could further boost more exploration on on-chip nonlinear devices assisted by non-Hermitian optics.     

Relationship between the spatial position of the seed and growth mode for single-crystal diamond grown with an enclosed-type holder

The relationship between the spatial position of the diamond seed and growth mode is investigated with an enclosed-type holder for single-crystal diamond growth using the microwave plasma chemical vapor deposition epitaxial method. The results demonstrate that there are three main regions by varying the spatial position of the seed. Due to the plasma concentration occurring at the seed edge, a larger depth is beneficial to transfer the plasma to the holder surface and suppress the polycrystalline diamond rim around the seed edge. However, the plasma density at the edge decreases drastically when the depth is too large, resulting in the growth of a vicinal grain plane and the reduction of surface area. By adopting an appropriate spatial location, the size of single-crystal diamond can be increased from 7 mm × 7 mm × 0.35 mm to 8.6 mm × 8.6 mm × 2.8 mm without the polycrystalline diamond rim.     

Preparation of a monolithic column with a mixed‐mode stationary phase of reversed‐phase/hydrophilic interaction for capillary liquid chromatography

A monolithic capillary column with a mixed‐mode stationary phase of reversed‐phase/hydrophilic interaction chromatography was prepared for capillary liquid chromatography. The monolith was created by an in‐situ copolymerization of a homemade monomer N,N‐dimethyl‐N‐acryloxyundecyl‐N‐(3‐sulfopropyl) ammonium betaine and a crosslinker pentaerythritol triacrylate in a binary porogen agent consisting of methanol and isopropanol. The functional monomer was designed to have a highly polar zwitterionic sulfobetaine terminal group and a hydrophobic long alkyl chain moiety. The composition of the polymerization solution was systematically optimized to permit the best column performance. The columns were evaluated by using acidic, basic, polar neutral analytes, as well as a set of alkylbenzenes and Triton X100. Very good separations were obtained on the column with the mixed‐mode stationary phase. It was demonstrated that the mixed‐mode stationary phase displayed typic dual retention mechanisms of reversed‐phase/hydrophilic interaction liquid chromatography depending on the content of acetonitrile in the mobile phase. The method for column preparation is reproducible.     

Sliding mode control for a diffuse interface tumor growth model coupling a Cahn–Hilliard equation with a reaction–diffusion equation

We consider the sliding mode control (SMC) problem for a diffuse interface tumor growth model coupling a Cahn–Hilliard equation with a reaction–diffusion equation perturbed by a maximal monotone nonlinearity. We prove existence and regularity of strong solutions and, under further assumptions, a uniqueness result. Then, we show that the chosen SMC law forces the system to reach within finite time a sliding manifold that we chose in order that the tumor phase remains constant in time.     

喷流冷却复合陶瓷薄片激光器的热特性仿真分析及实验研究

为分析喷流冷却复合陶瓷薄片激光器的热特性,设计用于冷却复合陶瓷薄片的喷流冷却系统.利用湍流换热理论和计算流体动力学仿真方法建立喷流冷却复合陶瓷薄片激光器的流固耦合热仿真模型,定义评价其冷却能力和冷却均匀性的定量参数.根据该仿真模型得到喷流冷却系统的最优设计参数,并进行实验验证.使用163孔喷板,流量为0.2kg/s,入口温度为20℃,在1200 W泵浦时获得359 W激光输出功率,并测得复合陶瓷薄片上表面的最高温度为92℃.激光输出功率与复合陶瓷薄片上表面温度均与泵浦功率呈近似正线性关系,且温度的实验值与仿真值相符度较高.     

Tightly coupled aeroelastic model implementation dedicated to fast aeroelastic tailoring optimisation of high aspect ratio composite wing

This paper presents the development of a code, called GEBTAero, dedicated to very flexible aircraft (VFA) aeroelasticity and especially the evaluation of aeroelastic tailoring effect on critical speeds. GEBTAero is an open source code consisting in a tightly coupling between a geometrically exact beam theory -and a finite state induced flow unsteady aerodynamic model, including an homogenisation tool. This model has been implemented in Fortran using GEBT code and optimised open source libraries with particular focus on computation speed. Besides a non linear transient dynamic simulation capacity, a particular focus is put on the fast critical speed computation strategy using a non-iterative modal approach about the geometrically non linear deformed shape of the wing with the computation of only a few aeroelastic modes. Computation speed and accuracy of this implementation is assessed using widely used aeroelastic test cases and compared successfully to other aeroelastic codes. Configurations using aeroelastic tailoring, which are the core target of this solver, are then evaluated numerically on a representative high aspect ratio anisotropic composite wing and a simple 2-ply composite laminates with both variable ply orientations. It illustrates the strong correlation between the structural bending/twisting coupling of an unbalanced composite laminates and its critical aeroelastic speed. It also shows the high sensitivity of ply orientation on the aeroelastic behaviour.     

Study of blood collection and sample preparation for analysis of vitamin D and its metabolites by liquid chromatography–tandem mass spectrometry

The analysis of vitamin D status, with special emphasis on 25-hydroxyvitamin D and 1,25-dihydroxyvitamin D, is gaining interest in clinical studies due to the classical and non-classical effects attributed to this prohormone. In this research, the influence of the two steps preceding determination (viz. sample collection and preparation) on the quantitative analysis of vitamin D and its more important metabolites has been studied. Two preparation approaches, deproteination and solid-phase extraction (SPE), have been evaluated in terms of sensitivity to delimit their application, thus establishing that detection of 1,25-dihydroxyvitamin D cannot be addressed by protein precipitation. Concerning sample collection, serum and plasma reported high accuracy (above 83.3%) for vitamin D and metabolites, while precision, expressed as relative standard deviation, was below 12.9% for all analytes in both samples. Statistical analysis revealed that serum and plasma provided similar physiological levels for vitamin D₃, 24,25-dihydroxyvitamin D₃ and 25-hydroxyvitamin D₃, while significantly different levels were obtained for 1,25-dihydroxyvitamin D₃, always higher in plasma than in serum. Sample collection and treatment have proved to be significant in the analysis of vitamin D and its relevant metabolites.