气相输运沉积制备c轴择优取向的碘化铋薄膜

铋基卤化物材料因其无毒和优良的光电性能而显示出巨大的应用潜力。BiI₃作为一种层状重金属半导体,已被用于X射线检测、γ射线检测和压力传感器等领域,最近其作为一种薄膜太阳能电池吸收材料备受关注。本文采用简单的气相输运沉积(VTD)法,以BiI₃晶体粉末作为蒸发源,在玻璃基底上得到高质量c轴择优取向的BiI₃薄膜。并通过研究蒸发源温度和沉积距离对薄膜物相和形貌的影响,分析了BiI₃薄膜择优生长的机理。结果表明VTD法制备的BiI₃薄膜属于三斜晶系,其光学带隙为~1.8 eV。沉积温度对薄膜的择优取向有较大影响,在沉积温度低于270 ℃时,沉积的薄膜具有沿c轴择优取向生长的特点,超过此温度,c轴择优取向生长消失。在衬底温度为250 ℃、沉积距离为15 cm时制备的薄膜结晶性能最好,晶体形貌为片状八面体。     

Growth and characterization of two-dimensional crystals for communication and energy applications

This review article covers the growth and characterization of two-dimensional (2D) crystals of transition metal chalcogenides, h-BN, graphene, etc. The chemical vapor transport method for bulk single crystal growth is discussed in detail. Top-down methods like mechanical and liquid exfoliation and bottom-up methods like chemical vapor deposition and molecular beam epitaxy for mono/few-layer growth are described. The optimal characterization techniques such as optical, atomic force, scanning electron, and Raman spectroscopy for identification of mono/few-layer(s) of the 2D crystals are discussed. In addition, a survey was done for the application of 2D crystals for both creation and deterministic transfer of single-photon sources and photovoltaic systems. Finally, the application of plasmonic nanoantenna was proposed for enhanced solar-to-electrical energy conversion and faster/brighter quantum communication devices.     

Synthesis of flower-like WS2 by chemical vapor deposition

Flower-like tungsten disulfide (WS₂) with a diameter of 5-10 μm is prepared by chemical vapor deposition (CVD). Scanning electron microscopy (SEM), energy dispersive spectrometer (EDS), Raman spectroscopy, and ultraviolet-visible (UV-vis) spectroscopy are used to characterize its morphological and optical properties, and its growth mechanism is discussed. The key factors for the formation of flower-like WS₂ are determined. Firstly, the cooling process causes the generation of nucleation dislocations, and then the "leaf" growth of flower-like WS₂ is achieved by increasing the temperature.     

煤直接液化油中混合酚的分离研究

利用分子筛择形特点，对煤直接液化油中的混合酚实施高效分离。本研究选取间甲酚和对甲酚作为分离煤直接液化油馏分段混合酚的模型化合物，采用化学液相沉积法对HZSM-5吸附剂的孔口结构进行改变，分析分子筛硅铝比及颗粒粒径对模型化合物间甲酚和对甲酚吸附分离性能的影响，以获得高性能固相吸附剂，并将其应用于180-190℃馏分段混合酚分离。结果表明，当分子筛硅铝比为25、粒径为3-5 μm时，分子筛的孔口结构调节效果最优；当正硅酸乙酯的最小用量为0.2 mL/g时，固相吸附剂的吸附量为0.03 g/g，对甲酚选择性高于95%。由于外表面沉积物对吸附剂的孔口结构变化，导致对甲酚选择性的提高。进一步采用HZSM-5（1）吸附剂对真实煤直接液化油混合酚的分离中发现，苯酚和对甲酚的选择性均达到100%。     

Preparation of coatings from a series of silicone/fluorine‐functionalized polyacrylates via electrophoretic deposition

Silicone/fluorine‐functionalized polyacrylates were synthesized and subsequently used to prepare corrosion‐resistant transparent coatings via electrophoretic deposition. The coated tin plate with the functionalized polyacrylate had a gloss value higher than 95.0 GU and resisted rust after immersion in a 5 wt% NaCl solution for 10 days. In addition, these coatings remained adhered strongly to the tin plates even after they were bent. It is hoped that this work will provide useful experimental data and assist researchers with the design of applicable coatings with desirable properties. Copyright © 2015 John Wiley & Sons, Ltd.     

甲烷浓度对碳化硅基底金刚石薄膜摩擦性能影响

利用热丝化学气相沉积法(HFCVD)在碳化硅基底上制备金刚石薄膜,采用场发射扫描电子显微镜、拉曼光谱仪、原子力显微镜研究了在不同甲烷浓度条件下制备的金刚石薄膜表面形貌及物相组成,在干摩擦条件下通过往复式摩擦磨损实验测试并计算了已制备金刚石薄膜的摩擦系数和磨损率,结合物相分析及摩擦磨损实验结果分析了甲烷浓度的改变对金刚石薄膜摩擦磨损性能的影响。结果表明,由于甲烷气体含量的升高,金刚石薄膜结晶质量下降,薄膜由微米晶向纳米晶转变。摩擦磨损实验结果显示:3%甲烷浓度条件下制备的金刚石薄膜耐磨性较好,磨损率为2.2×10^-7 mm³/mN;5%甲烷浓度条件下制备的金刚石薄膜摩擦系数最低(0.032),磨损率为5.7×10^-7 mm³/mN,制备的金刚石薄膜的耐磨损性能相比于碳化硅基底(磨损率为9.89×10^-5 mm³/mN)提升了两个数量级,显著提高了碳化硅基底的耐磨性。     

n-In0.35Ga0.65N/p-Si异质结的制备及其电学性能研究

采用双光路双靶材脉冲激光沉积(PLD)系统在p-Si衬底上外延生长InGaN薄膜,研究了InGaN薄膜的显微组织结构和n-InGaN/p-Si异质结的电学性能。研究表明,InGaN薄膜为单晶结构,沿[0001]方向择优生长,薄膜表面光滑致密,In的原子含量为35%。霍尔(Hall)效应测试表明In_0.35Ga_0.65N薄膜呈n型半导体特性,具有高的载流子浓度和迁移率及低的电阻率。I-V曲线分析表明In_0.35Ga_0.65N/p-Si异质结具有良好的整流特性,在±4 V时的整流比为25,开路电压为1.32 V。In_0.35Ga_0.65N/p-Si异质结中存在热辅助载流子隧穿和复合隧穿两种电流传输机制。经拟合,得到异质结的反向饱和电流为1.05×10^-8 A,势垒高度为0.86 eV,理想因子为6.87。     

Can a Procedure for the Growth of Single-layer Graphene on Copper be used in Different Chemical Vapor Deposition Reactors?

In the last decade, catalytic chemical vapor deposition (CVD) has been intensively explored for the growth of single-layer graphene (SLG). Despite the scattering of guidelines and procedures, variables such as the surface texture/chemistry of catalyst metal foils, carbon feedstock, and growth process parameters have been well-scrutinized. Still, questions remain on how best to standardize the growth procedure. The possible correlation of procedures between different CVD setups is an example. Here, two thermal CVD reactors were explored to grow graphene on Cu foil. The design of these setups was entirely distinct, one being a “showerhead” cold-wall type, whereas the other represented the popular “tubular” hot-wall type. Upon standardizing the Cu foil surface, it was possible to develop a procedure for cm²-scale SLG growth that differed only by the carrier gas flow rate used in the two reactors.     

Modeling of the elementary gas-phase reaction during chemical vapor deposition of silicon carbide from CH3SiCl3/H2

We established a gas-phase, elementary reaction model for chemical vapor deposition of silicon carbide from methyltrichlorosilane (MTS) and H₂, based on the model developed at Iowa State University (ISU). The ISU model did not reproduce our experimental results, decomposition behavior of MTS in the gas phase in an environment with H₂. Therefore, we made several modifications to the ISU model. Of the reactions included in existing models, 236 were lacking in the ISU model, and thus were added to the model. In addition, we modified the rate constants of the unimolecular reactions and the recombination reactions, which were treated as a high-pressure limit in the ISU model, into pressure-dependent rate expressions based on the previous reports (to yield the ISU+ model), for example, H₂(+M) → H + H(+M), but decomposition behavior remained poorly reproducible. To incorporate the pressure dependencies of unimolecular decomposition rate constants, and to increase the accuracies of these constants, we recalculated the rate constants of five unimolecular decomposition reactions of MTS using the Rice-Ramsperger-Kassel-Marcus method at the CBS-QB3 level. These chemistries were added to the ISU+ model to yield the UT2014 model. The UT2014 model reproduced overall MTS decomposition. From the results of our model, we confirmed that MTS mainly decomposes into CH₃ and SiCl₃ at the temperature around 1000°C as reported in the several studies.