机械磨抛对CdZnTe薄膜阻变特性的影响

采用磁控溅射法在ITO玻璃上制备了CdZnTe薄膜,探究机械磨抛对CdZnTe薄膜阻变特性的影响。通过对XRD图谱、Raman光谱、AFM显微照片等实验结果分析阐明了机械磨抛影响CdZnTe薄膜阻变特性的物理机制。研究结果表明,磁控溅射制备的薄膜为闪锌矿结构,F43m空间群。机械磨抛提高了CdZnTe薄膜的结晶质量;CdZnTe薄膜粗糙度(Ra)由磨抛前的3.42 nm下降至磨抛后的1.73 nm;磨抛后CdZnTe薄膜透过率和162 cm^-1处的类CdTe声子峰振动峰增强;CdZnTe薄膜的阻变开关比由磨抛前的1.2增加到磨抛后的4.9。机械磨抛提高CdZnTe薄膜质量及阻变特性的原因可能是CdZnTe薄膜在磨抛过程中发生了再结晶。     

石英晶体板非线性高频振动的拓展伽辽金法分析

针对考虑几何和材料非线性的石英晶体板厚度剪切振动和弯曲振动的方程组,利用扩展伽辽金法对该方程组进行转化和求解,分别获得了强烈耦合的厚度剪切振动模态和弯曲振动模态的频率响应关系,绘制了不同振幅比和不同驱动电压影响下的频率响应曲线图。数值计算结果表明可以选取石英晶片的最佳长厚比尺寸来避免两种模态的强烈耦合。驱动电压的变化将引起石英晶体谐振器厚度剪切振动频率的明显改变,必须将振动频率的漂移值控制在常用压电声波器件的允许值之内。扩展伽辽金法对石英晶体板非线性振动方程组的求解为非线性有限元分析和偏场效应分析奠定了基础。     

Solvent Influence on Absorption Spectra and Tautomeric Equilibria of Symmetric Azomethine-Functionalized Derivatives: Structural Elucidation and Computational Studies

A new series of azomethine-functionalized compounds was synthesized from the condensation of 2-hydroxy-1,3-propanediamine and 2-thienylcarboxaldehydes in the presence of a drying agent. The derivatives were spectroscopically characterized by NMR, LC-MS, UV/Vis, IR and elemental analysis. Variable temperature ¹H-NMR (−60 to +60 °C) was performed to investigate the effect of solvent polarity; the capability of solvent to form H-bond was found to dramatically influencing the tautomerization process of the desired structures. The calculated thermochemical parameters (ΔH₂₉₈, ΔG₂₉₈ and ΔS₂₉₈) at DFT and MP2 levels of theory explained that 3 b exists in equilibrium with two tautomers. The basis of the electronic absorptions was pursued through Time-Dependent Density-Functional Theory (TD-DFT). Analysis of the structural surfaces was inspected and the molecular electrostatic potential (MEP) demonstrated that the three functionalized compounds were relatively analogous in the electronic distributions. Furthermore, the electrophilic and nucleophilic centers lying on the molecular surfaces were probably playing a key-role in stabilizing the compounds through the nonclassical C−H⋅⋅⋅π interactions and hydrogen bonding. The impact of solvent polarity on absorption spectra were investigated via solvatochromic shifts. For instance, compound 3 c displayed a gradual shift of the maximum absorption to the red area when the solvent polarity was increased, recording a 21 nm of bathochromic shift. In contrast, no significant solvent-effect on 3 a and 3 b was observed. The solvation relation was pursued between Gutmann's donicity numbers the experimental λ_max; exhibited almost positive linear performance with a minor oscillation, that ascribe to the possible weak interface between the molecules of solute and designated solvents. The bandgap energy of all products were assessed experimentally using optical absorption spectra following Tauc approach, giving −4.050 ( 3 a ), −3.900 ( 3 b ) and −3.210 ( 3 c ) eV. However, the ΔE were computationally figured out from TD-DFT simulation to be −4.258 ( 3 a ), −4.022 ( 3 b ) and −3.390 ( 3 c ) eV.     

Surface charging behaviors of electrocatalytic interfaces with partially charged chemisorbates

The surface charge is a key concept in electrochemistry. Mathematically, the surface charge is obtained from a spatial integration of the volume charge along a particular direction. Ambiguities thus arise in choosing the starting and ending points of the integration. As for electrocatalytic interfaces, the presence of chemisorbates further complicates the situation. In this minireview, I adopt a definition of the surface charge within a continuum picture of the electric double layer. I will introduce surface charging behaviors of firstly ordinary electrochemical interfaces and then electrocatalytic interfaces featuring partially charged chemisorbates. Particularly, the origin of nonmonotonic surface charging behaviors of electrocatalytic interfaces is explained using a primitive model. Finally, a brief account of previous studies on the nonmonotonic surface charging behavior is presented, as a subline of the spectacular history of electric double layer.     

Multivariate optimization and comparison between conventional extraction (CE) and ultrasonic-assisted extraction (UAE) of carotenoid extraction from cashew apple

Carotenoids are an essential component of cashew and can be used in pharmaceuticals, cosmetics, natural pigment, food additives, among other applications. The present work focuses on optimizing and comparing conventional and ultrasound-assisted extraction methods. Every optimization step took place with a 1:1 (w:w) mixture of yellow and red cashew apples lyophilized and ground in a cryogenic mill. A Simplex-centroid design was applied for both methods, and the solvents acetone, methanol, ethanol, and petroleum ether were evaluated. After choosing the extractor solvent, a central composite design was applied to optimize the sample mass (59–201 mg) and extraction time (6–34 min). The optimum conditions for the extractor solvent were 38% acetone, 30% ethanol, and 32% petroleum ether for CE and a mixture of 44% acetone and 56% methanol for UAE. The best experimental conditions for UAE were a sonication time of 19 min and a sample mass of 153 mg, while the CE was 23 min and 136 mg. Comparing red and yellow cashews, red cashews showed a higher carotenoid content in both methodologies. The UAE methodology was ca. 21% faster, presented a more straightforward composition of extracting solution, showed an average yield of superior carotenoid content in all samples compared to CE. Therefore, UAE has demonstrated a simple, efficient, fast, low-cost adjustment methodology and a reliable alternative for other applications involving these bioactive compounds in the studied or similar matrix.     

Application of Machine Learning for Tool Condition Monitoring in Turning

The machining process is primarily used to remove material using cutting tools. Any variation in tool state affects the quality of a finished job and causes disturbances. So, a tool monitoring scheme (TMS) for categorization and supervision of failures has become the utmost priority. To respond, traditional TMS followed by the machine learning (ML) analysis is advocated in this paper. Classification in ML is supervised based learning method wherein the ML algorithm learn from the training data input fed to it and then employ this model to categorize the new datasets for precise prediction of a class and observation. In the current study, investigation on the single point cutting tool is carried out while turning a stainless steel (SS) workpeice on the manual lathe trainer. The vibrations developed during this activity are examined for failure-free and various failure states of a tool. The statistical modeling is then incorporated to trace vital signs from vibration signals. The multiple-binary-rule-based model for categorization is designed using the decision tree. Lastly, various tree-based algorithms are used for the categorization of tool conditions. The Random Forest offered the highest classification accuracy, i.e., 92.6%.

     

Rapid qualitative profiling and quantitative analysis of Juglandis Mandshuricae Cortex and seven flavonoids by ultra-high performance liquid chromatography–quadrupole/orbitrap high-resolution mass spectrometry

Juglandis Mandshuricae Cortex is the bark of Juglans mandshurica Maxim., which has been used as a folk medicine plant in China and India. In this study, an ultra-high performance liquid chromatography–quadrupole/orbitrap high-resolution mass spectrometry method was developed to clarify and quantify the chemical profiling of Juglandis Mandshuricae Cortex rapidly. A total of 113 compounds were characterized. Among them, seven flavonoids were simultaneously quantified in 15 min, including myricetin, myricetrin, taxifolin, kaempferol, quercetin, quercitrin, and naringenin. The method was validated for accuracy, precision, and the limits of detection and quantification. All calibration curves showed a good linear relationship (r > 0.9990) within test ranges. The intra- and inter-day relative standard deviations were less than 2.16%. Accuracy validation showed that the recovery was between 95.6 and 101.3% with relative standard deviation values below 2.85%. The validated method was successfully applied to determine the contents of seven flavones in Juglandis Mandshuricae Cortex from seven sources and the contents of these places were calculated respectively. This method provides a theoretical basis for further developing the medicinal value of Juglandis Mandshuricae Cortex.     

SAPO-34提升铁钒基催化剂抗碱性能研究

采用浸渍法制备Fe-VO_x/SAPO-34和Fe-VO_x/TiO₂脱硝催化剂,探究SAPO-34分子筛与TiO₂两种载体负载铁钒基氧化物催化活性及抗碱性能的差异。借助X射线衍射(XRD)、X射线光电子能谱(XPS)、氨气程序升温脱附(NH₃-TPD)、氢气程序升温还原(H₂-TPR)、原位红外漫反射(in-situ DRIFTs)等表征手段对催化剂的骨架结构、表面物化性质、氧化还原能力以及对反应气体的吸脱附情况进行分析。结果表明:SAPO-34分子筛内部特定的孔道结构和稳定的骨架,有利于活性组分在载体上均匀分散,降低碱金属对表面活性中心的物理覆盖作用;同时其表面丰富的酸位点能够作为碱金属捕获位,保护催化剂表面的活性中心,保证催化剂的吸附-反应过程能够正常进行,从而使Fe-VO_x/SAPO-34表现出良好的抗碱金属能力。     

以磷化铁为添加剂沿(111)面生长磷掺杂金刚石大单晶

掺杂是调控金刚石性能的一种重要手段。本文采用温度梯度法,在5.6 GPa、1 312 ℃的条件下,选用Fe₃P作为磷源进行磷掺杂金刚石大单晶的合成。金刚石样品的显微光学照片表明,随着Fe₃P添加比例的增加,金刚石晶体的颜色逐渐变深,包裹体数量逐渐增加,晶形由板状转变为塔状直至骸晶。金刚石晶形的变化表明Fe₃P的添加使生长金刚石的V形区向右偏移,这是Fe₃P改变触媒特性的缘故。红外光谱分析表明,Fe₃P的添加使金刚石晶体中氮含量上升,这说明磷的进入诱使氮原子更容易进入金刚石晶格中。激光拉曼光谱测试表明,随着Fe₃P添加比例的增加,所合成的掺磷金刚石的拉曼峰位变化不大,其半峰全宽(FWHM)值变大,这说明磷的进入使得金刚石晶格畸变增加。XPS测试结果显示,随着Fe₃P添加比例的增加,金刚石晶体中磷相对碳的原子百分含量也会增加,这意味着添加Fe₃P所合成的金刚石晶体中有磷存在。