Ag(I)-Catalyzed/Acid-Mediated Cascade Cyclization of ortho-Alkynylaryl-1,3-dicarbonyls to Access Arylnaphthalenelactones and Furanonaphthol Libraries via Aryl-Disengagement

ortho-Alkynylarylketone derivatives were employed as key precursors for a one-pot synthesis of arylnaphthalenelactone and furanonaphthol libraries. In this work, we discovered a cost-effective protocol to prepare arylnaphthalenelactones in one-pot using inexpensive starting material, malonate ester, which was conveniently functionalized leading to a variety of structures. Moreover, we also found an unexpected oxy-dearylation reaction which could be used to synthesize furanonaphthol analogs. These novel methods could be applied to a broad range of substrates to give the corresponding products in up to 83% yield. Notably, these classes of compounds exhibited more significant inhibition against protein-tyrosine phosphatase 1B (PTP1B) enzyme than a standard compound, ursolic acid.     

Multivariate optimization and comparison between conventional extraction (CE) and ultrasonic-assisted extraction (UAE) of carotenoid extraction from cashew apple

Carotenoids are an essential component of cashew and can be used in pharmaceuticals, cosmetics, natural pigment, food additives, among other applications. The present work focuses on optimizing and comparing conventional and ultrasound-assisted extraction methods. Every optimization step took place with a 1:1 (w:w) mixture of yellow and red cashew apples lyophilized and ground in a cryogenic mill. A Simplex-centroid design was applied for both methods, and the solvents acetone, methanol, ethanol, and petroleum ether were evaluated. After choosing the extractor solvent, a central composite design was applied to optimize the sample mass (59–201 mg) and extraction time (6–34 min). The optimum conditions for the extractor solvent were 38% acetone, 30% ethanol, and 32% petroleum ether for CE and a mixture of 44% acetone and 56% methanol for UAE. The best experimental conditions for UAE were a sonication time of 19 min and a sample mass of 153 mg, while the CE was 23 min and 136 mg. Comparing red and yellow cashews, red cashews showed a higher carotenoid content in both methodologies. The UAE methodology was ca. 21% faster, presented a more straightforward composition of extracting solution, showed an average yield of superior carotenoid content in all samples compared to CE. Therefore, UAE has demonstrated a simple, efficient, fast, low-cost adjustment methodology and a reliable alternative for other applications involving these bioactive compounds in the studied or similar matrix.     

Chelating Metal Ions in a Metal-Organic Framework for Constructing a Biomimetic Catalyst Through Post-modification

Crystal engineering, as a burgeoning technology, has been widely used to construct metalloporphyrins biomimetic catalysts. Herein, a bimetallic metal-organic framework (MOF) was constructed by 4-(4-carboxyphenyl)-1,2,4-triazole ligand, Co²⁺ and Zr⁴⁺ metal ions by solvothermal reaction(named PFC-88). A N,N-chelation site was found between the two adjacent ligands in PFC-88, consequently a porphyrin-like structure was obtained through chelating Fe³⁺ in this site by post-modification, named PFC-88-Fe. The result of a single crystal X-ray technology verified that Fe ions were successfully metalated in the N,N-chelation site of PFC-88, which is assisted by the X-ray absorption near-edge structure(XANES) spectra. An o-phenylenediamine oxidation reaction was applied to assessing the catalytic activity of PFC-88-Fe, in which the absorbance increases of phenazine-2,3-diamine at λ=418 nm were recorded by absorption spectroscopy in kinetic mode, exhibiting the application potential as a biomimetic catalyst.     

Green synthesis and characterization of Tb-Fe-O-Cu ceramic nanocomposite and its application in simultaneous electrochemical sensing of zinc,cadmium and lead

In this work, a green technique for preparing TbFeO₃/CuO was reported by employing Crataegus and Lantana Camara leaves as fuel and alkalizing agents, respectively. The new sensor based on the perovskite-type nanocomposite was employed as a sensitive and selective platform to detect Pb(II), Zn(II) and Cd(II) simultaneously. TbFeO₃/CuO/Carbon paste electrode (CPE) exhibited a large specific surface area and great electrical conductivity, which enhanced electron transport in the electrochemical process considerably. Moreover, square wave anodic stripping voltammetry (SWASV) was used for the investigation of some factors influencing the sensor sensitivity like pH, modifier concentration, as well as accumulation time and potential. Therefore, the low detection limit (LOD) and a wide linear range were obtained at optimum conditions. In this study, a linear range between 0.9 and 110 µg/L for three ions and LOD of 0.48, 0.29 and 0.12 for zinc, cadmium and lead were achieved, respectively. Moreover, TbFeO₃/CuO/CPE was employed to detect zinc, cadmium and lead ions simultaneously in the real samples so that the results have shown consistency with a standard inductively coupled plasma (ICP).     

以磷化铁为添加剂沿(111)面生长磷掺杂金刚石大单晶

掺杂是调控金刚石性能的一种重要手段。本文采用温度梯度法,在5.6 GPa、1 312 ℃的条件下,选用Fe₃P作为磷源进行磷掺杂金刚石大单晶的合成。金刚石样品的显微光学照片表明,随着Fe₃P添加比例的增加,金刚石晶体的颜色逐渐变深,包裹体数量逐渐增加,晶形由板状转变为塔状直至骸晶。金刚石晶形的变化表明Fe₃P的添加使生长金刚石的V形区向右偏移,这是Fe₃P改变触媒特性的缘故。红外光谱分析表明,Fe₃P的添加使金刚石晶体中氮含量上升,这说明磷的进入诱使氮原子更容易进入金刚石晶格中。激光拉曼光谱测试表明,随着Fe₃P添加比例的增加,所合成的掺磷金刚石的拉曼峰位变化不大,其半峰全宽(FWHM)值变大,这说明磷的进入使得金刚石晶格畸变增加。XPS测试结果显示,随着Fe₃P添加比例的增加,金刚石晶体中磷相对碳的原子百分含量也会增加,这意味着添加Fe₃P所合成的金刚石晶体中有磷存在。     

Terahertz generation in quantum cascade structures by two-color deriving fields: An approach to reach inversion population via optical pumping

In this paper, a quantum cascade laser (QCL) design is proposed based on GaAs/AlGaAs material system, which simultaneously operates at three widely separated wavelengths (${\lambda }_1=11.1\mu m,{\lambda }_2=14.1\mu m$ and ${\lambda }_{THz}=60\mu m$). In the design, all the wavelength radiations are achieved by the engineering of the electronic spectrum via the quantum-well widths and the applied electric field in a single active region within a same waveguide. The mid-infrared (mid-IR) wavelengths are obtained by adoption a dual-upper-state active region, and the proposed design aims to use both the mid-IR radiations as the coherent deriving fields to populate the upper THz lasing state to aid the THz-laser population inversion via optical pumping instead of direct electrical injection. A detailed analysis of electronic transport in the structure is carried out using a multi-level rate-equation model. The results show that the proposed structure offers an alternative approach to room temperature THz generation in QCLs.     

材料表征方法理论与实践课程的改革与建设*

通过与超星专业慕课制作团队合作搭建网络教学平台,将线上慕课教学与线下实验教学相结合,对材料表征方法理论与实践课程进行了全方位的改革。与传统实验教学相比,改革后的课程不仅能够激发学生的学习兴趣,实现时间空间的相对自由,还可以完善考核机制,提升教学质量,从而为高校化学研究生实验课程的改革提供一定的借鉴意义。     

气相输运沉积制备c轴择优取向的碘化铋薄膜

铋基卤化物材料因其无毒和优良的光电性能而显示出巨大的应用潜力。BiI₃作为一种层状重金属半导体,已被用于X射线检测、γ射线检测和压力传感器等领域,最近其作为一种薄膜太阳能电池吸收材料备受关注。本文采用简单的气相输运沉积(VTD)法,以BiI₃晶体粉末作为蒸发源,在玻璃基底上得到高质量c轴择优取向的BiI₃薄膜。并通过研究蒸发源温度和沉积距离对薄膜物相和形貌的影响,分析了BiI₃薄膜择优生长的机理。结果表明VTD法制备的BiI₃薄膜属于三斜晶系,其光学带隙为~1.8 eV。沉积温度对薄膜的择优取向有较大影响,在沉积温度低于270 ℃时,沉积的薄膜具有沿c轴择优取向生长的特点,超过此温度,c轴择优取向生长消失。在衬底温度为250 ℃、沉积距离为15 cm时制备的薄膜结晶性能最好,晶体形貌为片状八面体。     

雾化辅助化学气相沉积法氧化镓薄膜生长研究

采用自主设计搭建的雾化辅助化学气相沉积系统设备,开展了Ga₂O₃薄膜制备及其特性研究工作。通过X射线衍射研究了沉积温度、系统沉积压差对Ga₂O₃薄膜结晶质量的影响。结果表明,Ga₂O₃在425~650 ℃温度区间存在物相转换关系。随着沉积温度从425 ℃升高至650 ℃,薄膜结晶分别由非晶态、纯α-Ga₂O₃结晶状态向α-Ga₂O₃、β-Ga₂O₃两相混合结晶状态改变。通过原子力显微镜表征探究了生长温度对Ga₂O₃薄膜表面形貌的影响,从475 ℃升高至650 ℃时,薄膜表面粗糙度由26.8 nm下降至24.8 nm。同时,高分辨X射线衍射仪测试表明475 ℃、5 Pa压差条件下的α-Ga₂O₃薄膜样品半峰全宽仅为190.8″,为高度结晶态的单晶α-Ga₂O₃薄膜材料。