X射线天文望远镜的进展

综述了近年来X射线天文望远镜(如准直型望远镜、编码孔径望远镜、正入射周期多层膜望远镜、掠入射单层膜望远镜和掠入射非周期多层膜望远镜以及新型的“龙虾眼”型望远镜)的发展；阐述了各种X射线天文望远镜工作的原理和成像特点，指出各种X射线天文望远镜之间的性能是相互补充的；简要说明了国内近年来在X射线天文望远镜研究方面取得的进展，并展望了下一步工作．     

B_4C/Mo/Si high reflectivity multilayer mirror at 30.4 nm

The B4C/Mo/Si high reflectivity multilayer mirror was designed for He-Ⅱradiation (30.4 nm) using the layer-by-layer method. The theoretical peak reflectivity was up to 38.2% at the incident angle of 5℃. The B4C/Mo/Si multilayer was fabricated by direct current magnetron sputtering and measured at the National Synchrotron Radiation Laboratory (NSRL) of China. The experimental reflectivity of the B4C/Mo/Si multilayer at 30.4 nm was about 32.5%. The promising performances of the B4C/Mo/Si multilayer mirror could be used for the construction of solar physics instrumentation.     

低温退火的X射线W/Si多层膜应力和结构性能

W/Si多层膜反射镜在硬X射线天文望远镜中有重要应用. 为减小其应力对反射镜面形和望远镜分辨率的影响, 同时保证较高的反射率, 采用150, 175和200 ℃ 的低温退火工艺对采用磁控溅射镀制的W/Si周期多层膜进行后处理. 利用掠入射X射线反射测试和样品表面面形测试对退火前后W/Si多层膜的应力和结构进行表征. 结果表明, 在150 ℃ 退火3 h 后, 多层膜1级峰反射率和膜层结构几乎没有发生变化, 应力减少约27%; 在175 ℃ 退火3 h后, 多层膜膜层结构开始发生变化, 应力减少约50%; 在200 ℃退火3 h 后, 多层膜应力减小超过60%, 但1级布拉格峰反射率相对下降17%, 且膜层结构发生了较大变化. W, Si界面层的增大和相互扩散加剧是应力和反射率下降的主要原因.     

Fabrication and Characterization of Ni Thin Films Using Direct-Current Magnetron Sputtering

Ni films are deposited by using ultra high vacuum dc magnetron sputtering onto silicon substrates at room temperature, and the high-quality and high-density films are prepared. The parameters, such as thickness, density and surface roughness, are obtained by using small-angle x-ray diffraction (XRD) analyses with the Marquardt gradient-expansion algorithm. The deposition rate is calculated and the Ni single layer can be fabricated precisely. Based on the fitting results, we can find that the surface roughness of the Ni films is about 0.7nm, the densities of Ni films are around 97% and the deposition rate is 0.26nm/s. The roughness of the surface is also characterized by using an atomic force microscope (AFM). The changing trend of the surface roughness in the simulation of XRD is in good agreement with the AFM measurement.     

X射线Kirkpatrick-Baez显微镜用超反射镜的研制

 介绍了一种可应用于X射线Kirkpatrick-Baez（KB）显微镜的光学元件—X射线超反射镜。选用的W和B₄C作为镀膜材料，膜对数为20，采用单纯型调优的方法实现了X射线超反射镜设计，用磁控溅射的方法在Si基片上完成了W/B₄C X射线超反射镜的制备。采用高分辨率X射线衍射仪（8 keV）测量了X射线超反射镜的反射特性。制备的X射线超反射镜在掠入射角分别为1.052°和1.143°处，反射角度带宽为0.3°，反射率达到20%，可满足KB型显微镜的要求。     

Design, Fabrication and Measurement of Ni/Ti Multilayer Used for Neutron Monochromator

Ni/Ti multilayers, which can be used for neutron monochromators, are designed, fabricated and measured. Firstly, their reflectivities are simulated based on the Nevot-Croce model. Reflectivities of two Ni/Ti multilayer mirrors with periods d = 10.3 nm （M1） and d = 7.8 nm （M2） are calculated. In the calculation, the reflectivity of the Ni/Ti multilayer is taken as a function of the gazing angle with different roughness factors δ =1.0 nm and = 1.5 nm. Secondly, these two multilayers are fabricated by the direct current magnetron sputtering technology. Thirdly their structures are characterized by small-angle x-ray diffraction. The roughness factors are fitted to be 0.68 nm and 1.16nm for M1 and M2, respectively. Finally their reflective performances are measured on the V14 neutron beam line at the Berlin Neutron Scattering Centre （BENSC）, Germany. The experimental data show that the grazing angle of the reflected neutron intensity peak increases, but the reflected neutron intensity decreases, with the decreasing periods of the multilayers.     

水窗波段反射式偏振光学元件的设计和制作

水窗波段是软X射线进行生物活细胞显微成像的最佳波段,因此对于水窗波段偏振光学元件的研究有着非常重要的意义。用菲涅耳公式计算出在水窗波段内不同材料组合对应不同波长的最大反射率,模拟分析了多层膜周期和表界面粗糙度对多层膜偏振光学元件性能的影响。用超高真空磁控溅射镀膜设备,制作出2．40nm、3．00nm和4．30nm波长处W／B4C多层膜偏振元件,并用X射线衍射仪对元件的周期厚度进行了测量,得到的测量结果与设计值偏差很小,可以进行实际应用。为水窗波段反射式偏振光学元件的研究提供了理论依据,同时也为相应偏振光学元件的制备确定了合适的工艺参量。     

基于遗传算法的30.4 nm多层膜设计

阐述了用遗传算法设计周期和非周期多层膜的原理和实现过程,完成了30.4 nm Mg/SiC周期和非周期多层膜设计,研究了遗传算法中不同种群数和多层膜膜厚取值范围对优化结果的影响.计算发现,种群数的恰当选取是使算法快速达到或逼近最优解的前提,膜厚取值范围的合理选择是提高算法效率的关键.设计得到入射角10°的周期多层膜和15°~22°范围内的宽角多层膜在波长30.4 nm处的反射率依次为56.57%与39.96±0.29%,5°入射的双功能多层膜在波长30.4 nm和58.4 nm处的反射率分别为54.1%和0.1%.结果表明遗传算法也是一种很好的多层膜设计方法.     

13.9 nm马赫贞德干涉仪用软X射线分束镜研究

 介绍了13.9 nm马赫贞德干涉仪用软X射线分束镜的设计、制备与性能检测。基于分束镜反射率和透过率乘积最大的评价标准，设计了13.9 nm软X射线激光干涉实验用多层膜分束镜。采用磁控溅射方法在有效面积为10 mm×10 mm、厚度为100 nm的Si3N4基底上镀制了Mo/Si多层膜，制成了多层膜分束镜。利用X射线掠入射衍射的方法测量了Mo/Si多层膜的周期。用扩束He-Ne激光束进行的投影成像方法定性分析了分束镜的面形精度，利用光学轮廓仪完成了分束镜面形精确测量。利用北京同步辐射装置测量了分束镜反射率和透射率，在13.9 nm处，分束镜反射率和透过率乘积达4%。使用多层膜分束镜构建了软X射线马赫贞德干涉仪，并应用于13.9 nm软X射线激光干涉实验中，获得了清晰的含有C8H8等离子体电子密度信息的动态干涉条纹。     

光信息科学与技术专业实验室建设探讨

根据同济大学光信息科学与技术专业的教学计划,同时结合我校的科研条件,筹建了相应的专业实验室。介绍了同济大学光信息科学与技术专业实验室建设过程中的规划和7类实验项目的内容和意义,如光谱学系列实验、光学系统CAD设计系列、光学薄膜CAD设计系列、光学薄膜特性测试实验、激光系列实验、光电基础和光电探测系列实验和光纤光学与光纤通信系列实验。