排序方式: 共有11条查询结果,搜索用时 171 毫秒
1.
2.
3.
4.
5.
By means of numerical simulations, we analyze the scintillation characterization for multiple incoherent uplink Gaussian beams under weak fluctuations cases. Because truly independent beams are difficult to create, we present a more general but approximate model for the multiple of beams traveling through partially correlated paths. This model compares with wave-optics simulations and highlights the reduced correlation coefficient as the beam separation is increased. The scintillation index of three and six incoherent uplink Gaussian beams is also induced. The result shows that the scintillation index decreases with the increase of beams amount and beam separation. When the beams amount and strength of atmospheric turbulence are fixed, the reduction of scintillation index is affected by the ratio of beams separation and the Fried length. The corresponding physical mechanisms for the results are discussed. 相似文献
6.
100kW功率固体激光中继镜系统对1km高度目标作用效果模拟 总被引:3,自引:0,他引:3
分析了激光中继镜技术的概念及丁作过程,建立了中继镜系统模型,并在Hufnagel-Valley 5/7大气湍流模型条件下分别计算了100 kW功率,10 km高度,发射、接收、二次发射望远镜均为外径0.5 m、内径0.2 m望远镜的固体激光中继镜系统和100 kW功率,外径0.5 m、内径0.2 m发射望远镜的常规高能激光系统对1 km高度目标作用的极值功率密度与目标水平距离的关系曲线.由于中继镜系统对目标可作用时间长,根据相关资料确定常规激光系统和中继镜系统的极值功率密度破坏阈值标准分别为4000 W/cm2和800 W/cm2.分析结果得到常规高能激光系统对目标的最大可作用距离为1.38 km,中继镜系统的最大可作用距离为12.2 km. 相似文献
7.
针对热容激光器的热透镜效应,给出了棒状钕玻璃热容激光器的热透镜公式表达式。理论上分析了热透镜焦距自平衡补偿方法的基本原理。在考虑了棒状钕玻璃热容激光器的具体特性的基础上,设计了一种简单的热透镜焦距自平衡补偿方法,使光抽运钕玻璃热容激光器在热透镜焦距变化情况下,可以使激光输出光斑大小稳定。为了解棒状热容激光器热透镜焦距的影响,利用自研的光栅型曲率传感器测量了热容激光器总的热透镜等效焦距的大小,结果表明热传导在抽运光发射完20 s左右后才建立热平衡产生了明显的热透镜效应; 随着抽运脉冲个数的增加,热透镜效应随之变大。 相似文献
8.
9.
基于标量衍射理论建立了光谱色散平滑(SSD)、随机相位板(RPP)和偏振匀滑(PS)联用的光束匀滑方案数值仿真模型。以斑纹对比度和偏振度为主要评价参量,利用该模型研究了径向偏振调制的匀滑及消偏振特性。研究表明,径向偏振调制可以有效降低聚焦光斑斑纹对比度和偏振度。使用半波片拼接方式产生近似径向偏振光时,拼接单元数对匀滑及偏振特性影响较小,8片拼接的匀滑效果已与理想径向偏振光几乎一致。对比分析了径向偏振调制、正交偏振调制和双折射楔三种PS方式,结果表明,由于三种PS方式本质上的一致性,光束的匀滑及偏振特性差别较小。 相似文献
10.
We demonstrate a high efficiency 1083 nm fibre amplifier tandem pumped by a 1030 nm fibre laser. The 1030 nm fibre laser is coupled into a 25 m long single clad ytterbium doped fibre via a high power wave division multiplexer to core pump the 1083 nm signal laser. An output power of 4.5 W and a power conversion efficiency of 76.6% are achieved without power-roll. The performance of the amplifier can be improved by optimizing the gain fibre length. 相似文献