Chemical profiling of Ziziphi spinosae semen using on-line comprehensive two-dimensional liquid chromatography-mass spectrometry based on a novel phthalic anhydride bonded stationary phase

Ziziphi spinosae semen has been widely used to treat insomnia and anxiety. To profile its chemical components, an online comprehensive two-dimensional liquid chromatography-mass spectrometry was developed. In this two-dimensional liquid chromatography system, a novel phthalic anhydride-bonded stationary phase column was combined with a C18 column. As a result, this new stationary phase exhibited remarkable differences in separation selectivity from C18, achieving a good orthogonality of 83.3%. Moreover, this new stationary phase with weaker hydrophobicity than C18 realized solvent compatibility in the online configuration. Coupled with tandem MS, 154 compounds were identified, including 51 unreported compounds. Compared with one-dimensional liquid chromatography-mass spectrometry, this online two-dimensional liquid chromatography-mass spectrometry system exhibited a much higher resolving power in isomer separation. This work provided an effective separation and characterization method for the material basis of Ziziphi spinosae semen. This strategy provides ideas for the material basis research of other traditional Chinese medicines.     

Removal of low-concentration benzene in indoor air with plasma-MnO2 catalysis system

Non-thermal plasma (NTP) and combined plasma-MnO₂ catalytic (CPMC) air cleaners were tested for removal of low-concentration benzene in air. Both air cleaners were made of stainless steel needle matrix plate and used DC corona discharger. The effects of discharge power and relative humidity (RH) on benzene removal efficiency were investigated in a closed chamber. The intermediate products produced in purification processes were analyzed using gas chromatography-mass spectrometer (GC-MS). The concentrations of discharge byproducts and CO₂ selectivity produced in both processes were also compared. It was found that the benzene removal efficiency increased with discharge power in both systems; With the increase of RH in air, benzene removal efficiency firstly increased and then decreased in NTP while it gradually decreased in CPMC. For a fixed discharge power of 9 W and RH of 20% in CPMC, the conversion of benzene increased from 82.9% to 89.6%, the CO₂ selectivity increased from 38% to 80%, the concentration of O₃ decreased from 25.3 ppm to 1.3 ppm, and NO₂ formation decreased from 234 ppm to 25.7 ppm, compared with NTP.     

Numerical study of a well boat operating at a fish farm in current

Dynamic response of a well boat operating at a fish farm in current is investigated numerically. An objective is to determine the operational conditions of the well boat. In terms of the fish farm, a realistic set-up (with single cage) is considered, including a floating collar, an elastic sinker tube, a flexible-closed net cage and a complex mooring system. A time-domain solution is used to find the steady configuration and response. Transverse viscous current loads are estimated using the cross-flow principle. The drag coefficients are obtained empirically by considering cross-sectional details, free surface and three-dimensional (3D) flow effects. The drag force is experimentally validated. The effect of the ship wake on the net loading is also assessed.The most critical scenario with the well boat placed at the weather side of the fish farm is analyzed in detail. Critical response variables for operational limits are the maximum anchor-line tensions and floater stresses. Numerical results show that the anchor loads will increase more than 40% in small current velocities and up to 90% in high current velocities due to the viscous current loads on the boat. There is also a strong increase of the floating collar deformations and stresses when the well boat is in contact with the floating collar.A sensitivity analysis has been carried out to identify the physical parameters affecting the anchor loads and the maximum stress in the floating collar. From our studies, the anchor loads are more sensitive to current direction, bottom weight system, sinker tube depth and mooring line properties (pretension load, anchor chain weight, etc.) and less sensitive to other parameters such as floating collar stiffness and cross-sectional drag coefficients of the well boat. The shading effect of the well boat on the fish-farm inflow has been examined and appeared not negligible with 4% to 10% reduction of the anchor loads for the studied current conditions. The maximum stress in the floating collar is sensitive to well-boat loads related parameters (current direction, cross-sectional drag coefficient) and pretension load in the anchor line; not so sensitive to net loading related parameters such as sinker tube depth and sinker tube weight.Lastly, the operational conditions of the well boat at the fish farm were discussed. Numerical results show that the maximum stresses in the floating collar should be of major concern. The loads in the mooring lines are moderate compared with the corresponding breaking limits.     

Structural response of high solidity net cage models in uniform flow

Hydrodynamic loads acting on a fish farm may be affected by the growth of different biofouling organisms, mainly due to increased solidity of the nets. In this paper, the hydrodynamic loads acting on high solidity net cage models subjected to high uniform flow velocities and the corresponding deformation of the net cages are studied. Model tests of net cylinders with various solidities were performed in a flume tank with a simulated current. Standard Morison-type numerical analyses were performed based on the model tests, and their capability of simulating the occurring loads and the observed net cage deformations for different flow velocities was evaluated.Large deformations of the net cage models were observed, and at high velocities the deformations were close to what is physically possible. Net cage deformation appeared to be less dependent on solidity than on flow velocity and weights. Drag forces increased with increasing flow velocity and were dependent on both bottom weights and netting solidity. For the lowest solidity net, drag forces were close to proportional to flow velocity. For the three high solidity nets, the measured drag forces were of similar magnitude, and drag increased less with increasing flow velocity above approximately 0.5 m/s than at lower velocities.This study shows that a basic reduced velocity model is not sufficient to model the interaction between the fluid flow and net (hydroelasticity) for high solidity net cages subjected to high flow velocities.The standard numerical analysis was in general able to make good predictions of the net shape, and was capable of making an acceptable estimate of hydrodynamic loads acting on the lowest solidity net model (Sn=0.19). For high solidities and large deformations, numerical tools should account for changes in water flow and the global drag coefficient of the net.     

Crystallization of colloidal crystal on hydrogel surface

A dip-coating method to fabricate wet and dry type of colloidal crystal films was developed. The wet type of colloidal crystal film was fabricated by lifting an agarose-hydrogel-coated substrate out of an aqueous suspension containing monodisperse polymer spheres and the dry type of colloidal crystal film was derived by following desiccation of the wet film. Monodisperse spheres formed ordered structures in the both type of the films, which contributed sharp reflection peaks. Brilliant colors were observed when the reflection peaks fell in the visible region. Formation mechanism of the colloidal crystal and their optical properties were discussed.     

己烯雌酚在导电炭黑糊电极上的伏安行为及其在痕量检测中的应用

由于具有较高的信/噪比,导电炭黑糊电极(CCBPE)具有优良的电分析化学性能。论文采用循环伏安(CV)及线性扫描伏安(LSV)等方法研究了己烯雌酚(DES)在CCBPE上的电化学行为,初步探讨了电极响应机理。在此基础上,对影响伏安响应信号的因素(诸如支持电解质种类、pH值、富集电位和富集时间等)进行了研究和优化。在优化条件下,DES的氧化峰电流与其浓度在3.1×10-9～1.55×10-7mol/L范围内呈良好的线性关系,检测限为1.55×10-9mol/L(S/N=3)。据此建立了一种快速、高灵敏的DES检测方法。应用于测定经过简单预处理的淡水渔业水样,得到了满意的结果。     

Numerical modeling of current loads on a net cage considering fluid–structure interaction

In this paper we propose and discuss a numerical method to model the current loads on a net cage. In our numerical model, the fluid–structure interaction is taken into consideration. The net cage is modeled on the mass-spring model; the flow field is modeled by the finite volume method (FVM). A novel hybrid volume approach is used to add the resistance force of the net cage into the flow field for coupling the fluid and net. The net resistance to the flow is calculated directly by the net’s current load using Newton’s Third Law. The resistance force is discretized in the hybrid volume and represented in the source term of the Navier–Stokes equation. By using the hybrid volume method, the mesh grid is separated from the net shape, and sparse grid (0.1 m) can be used to calculate the flow field for computational efficiency. Based on the detailed flow field, we can predict the net’s current load more accurately. The final results are derived by the segregated iterative calculation of net shape and flow field. Current forces acting on both rigid and flexible net cages are simulated at water velocity from 0 to 1 m/s; the simulation results of proposed numerical method are compared with the existing experiments, good agreements are shown in both flow field and current force, the mean normalized absolute error of the current force between simulations and measurements is about 5%.     

Highly Active TiO2/Polyelectrolytes Hybrid Multilayered Hollow Nanofibrous Photocatalyst Prepared from Electrouspun Fibers Using Electrostatic Layer-by-Layer Technique

Compared to conventional film photocatalysts, fiber photocatalyst has a greater surface-to-volume ratio and a 3-D open structure that allows its surface active sites to be accessible for reactants more easily and effectively. However, TiO ₂ powder (Degussa P25), by itself, cannot be prepared in the form of fibers, but with the help of a polymer nanofiber, TiO ₂ particles can be immobilized in a fibrous network of polyelectrolyte. Here, hybrid multilayered hollow nanofibers (HMHNFs) composed of TiO ₂ /polyelectrolyte (PE) have been prepared by a combination of a electrospinning method and layer-by-layer (LBL) technology. The results show that both the average diameter and the wall thickness of the HMHNFs can be well controlled by the template, as well as the number of coating layers. The dried morphology of the obtained HMHNFs is dependent on the inner deposited numbers of the polyelectrolyte layers. When compared with other nanostructured TiO ₂ materials, such as commercial TiO ₂ nanoparticles (P25, Degussa) and TiO ₂ films, the hollow TiO ₂ /PE hybrid nanofibers exhibited higher photocatalytic activities.     

真空离子溅射法制备TiO2∶Au复合纳米纤维新型光催化剂及其 降解乙醛性能研究

采用静电纺丝技术与真空离子溅射相结合的方法制备了TiO2∶Au复合纳米纤维, 并采用SEM和X射线电子能谱仪对其进行了表征. 结果表明TiO2∶Au纳米纤维的表面形态能通过Au沉积时间得到很好的控制. 同时在紫外光照射下采用乙醛体系考察了TiO2纳米纤维和TiO2∶Au复合纳米纤维催化剂降解乙醛性能, 结果证明TiO2∶Au复合纳米纤维具有更好的催化效率, 紫外光照射70 min后乙醛被完全降解.     

C60团簇与等离子体相互作用的分子动力学模拟

用分子动力学模拟方法研究了C60团簇与稠密等离子体的相互作用。在线性化的伏拉索夫-泊松理论框架下,借助于经典的等离子体介电函数,推导了团簇的阻止本领的一般表达式。用数值方法求解了团中离子的运动方程,研究了团簇的库仑爆炸过程,讨论了入射速度、等离子体密度和电子温度对阻止本领和库仑爆炸的影响。结果发现尾流效应降低了C60团簇离子的库仑爆炸速度,甚至压缩了团簇的结构,在高速、低密、高温的情况下库仑爆炸进行得更快。