首页 | 本学科首页   官方微博 | 高级检索  
文章检索
  按 检索   检索词:      
出版年份:   被引次数:   他引次数: 提示:输入*表示无穷大
  收费全文   284篇
  免费   46篇
  国内免费   1002篇
化学   105篇
晶体学   8篇
力学   1030篇
综合类   6篇
数学   15篇
物理学   168篇
  2022年   7篇
  2021年   9篇
  2020年   4篇
  2019年   8篇
  2018年   17篇
  2017年   51篇
  2016年   61篇
  2015年   58篇
  2014年   47篇
  2013年   84篇
  2012年   44篇
  2011年   55篇
  2010年   48篇
  2009年   63篇
  2008年   39篇
  2007年   68篇
  2006年   84篇
  2005年   79篇
  2004年   67篇
  2003年   52篇
  2002年   53篇
  2001年   53篇
  2000年   53篇
  1999年   40篇
  1998年   50篇
  1997年   24篇
  1996年   29篇
  1995年   16篇
  1994年   18篇
  1993年   16篇
  1992年   15篇
  1991年   7篇
  1990年   10篇
  1989年   1篇
  1988年   1篇
  1986年   1篇
排序方式: 共有1332条查询结果,搜索用时 31 毫秒
1.
本文通过固结磨料球与KDP晶体对磨的单因素试验探究固结磨料球中反应物种类、磨粒浓度、反应物浓度、基体硬度对摩擦系数、磨痕截面积和磨痕处粗糙度的影响,试验结果表明:KHCO3固结磨料球对磨后磨痕对称性好,磨痕处的粗糙度值低;磨痕截面积随磨粒和反应物浓度的增加而增大,随基体硬度的增大而降低;磨痕处粗糙度随磨粒和反应物浓度的增加先降低后上升,随基体硬度的增大先上升后降低;摩擦系数受磨粒和反应物浓度影响不明显,随基体硬度的增大而降低。选择KHCO3作为反应物,Ⅰ基体,磨粒浓度为基体质量的100%,反应物浓度为15%制备固结磨料球与KDP晶体对磨后的磨痕轮廓对称度好且磨痕处粗糙度值低,以该组分制备固结磨料垫干式抛光KDP晶体,可实现晶体表面粗糙度Sa值为18.50 nm,材料去除率为130 nm/min的高效精密加工。  相似文献   
2.
对3种不同残奥(RA)含量的马氏体高强钢进行干滑动摩擦磨损试验, 研究RA含量对其磨损性能的影响. 利用扫描电镜、透射电镜、X射线衍射仪等对试验后的磨损表面及横截面显微组织进行表征. 结果表明, RA含量越高, 磨损表面越光滑, 摩擦系数和磨损率越小, 也即马氏体高强钢的耐磨性越好. 磨损引起的大应变使RA发生应变诱导马氏体相变, 导致硬度和硬化层厚度显著增大. RA含量最高的HT3试样的硬度提高了18.3%, 硬化层厚度达70μm. 相比RA含量低的试样, HT3试样表现出很好的耐磨性. 这是因为马氏体相变使硬度逐步增加, 抗裂纹萌生能力提高; 同时由于亚表面良好的韧性, 可延缓和阻止裂纹扩展, 使得点蚀和剥落不易形成. 因此, 要提高马氏体高强钢的耐磨性, 除了硬度要求外, 还需要考虑其亚表面韧性.  相似文献   
3.
应用BP神经网络建立了磨损率与接触应力、滑动速度和材料硬度之间的非线性关系模型,并对该网络模型进行了验证和测试,结果表明,训练良好的神经网络模型能够准确反映样本所蕴含的内在磨损规律,且具有较好的预测效果。基于非线性弹簧阻尼模型和修正的Coulomb摩擦力模型对含间隙曲柄滑块机构进行数值仿真分析,获得间隙机构运动副的接触应力和相对滑动速度,利用训练好的神经网络磨损模型对轴套的磨损进行迭代磨损预测分析,发现随着曲柄转数的增加,轴套表面一些特定位置处的磨损越来越严重,最终导致轴套表面出现非均匀磨损现象,其原因是间隙机构运转过程在一些特定位置处产生了较大接触应力和碰撞力。  相似文献   
4.
This article reports on the implementation of a soft computing technique based on artificial neural networks (ANNs) in analyzing the wear performance of a new class of hybrid composites filled with Linz–Donawitz slag (LDS). LDS is a major solid waste generated in huge quantities during steel making. It comes from slag formers such as burned lime/dolomite and from oxidizing of silica, iron etc. while refining the iron into steel in the LD furnace. In this work, hybrid composites consisting of short glass fiber (SGF) reinforced epoxy filled with different LDS content (0, 7.5, 15 and 22.5 wt%) are prepared by simple hand lay‐up technique. Solid particle erosion trials, as per ASTM G 76 test standards, are conducted on the composite samples following a well‐planned experimental schedule based on Taguchi design of experiments. Significant process parameters predominantly influencing the rate of erosion are identified. The study reveals that the LDS content is the most significant among various factors influencing the wear rate of these composites. Further, a model based on ANN for the prediction of erosion performance of these composites is implemented. The ANN prediction profiles for the characteristic wear properties exhibit very good agreement with the measured results demonstrating that a well‐trained network has been created. The simulated results explaining the effect of significant process variables on the wear rate indicate that the trained neural network possesses enough generalization capability of predicting wear rate even beyond the experimental range. Copyright © 2014 John Wiley & Sons, Ltd.  相似文献   
5.
石墨烯环氧涂层的耐磨耐蚀性能研究   总被引:6,自引:1,他引:5  
将石墨烯水分散液添加到双组份水性环氧树脂中制备石墨烯固体润滑涂层,采用交流阻抗谱和动电位极化曲线研究了涂层在模拟海水(3.5%Na Cl溶液)中的电化学腐蚀行为和失效过程;采用UMT-3摩擦磨损试验机评价了三种石墨烯基环氧涂层在干摩擦和海水环境条件下的滑动摩擦磨损行为,并分析了其磨痕形貌和磨损机理.结果表明:石墨烯可以明显提高水性环氧的涂层电阻和电荷转移电阻,并降低环氧涂层在干燥条件与海水环境的摩擦系数和磨损率;石墨烯环氧涂层的摩擦系数和磨损率在海水环境中均比干摩擦低.  相似文献   
6.
A novel fluorinated chain extender, (1‐(ethyl(2‐hydroxyethyl)amino)‐3‐ ((3,3,4,4,5,5,6,6,7,7,8,8,8‐tridecafluorooctyl)oxy)propan‐2‐ol) (FPO), was synthesized and characterized by nuclear magnetic resonance (NMR), Fourier transform infrared (FTIR), and elemental analysis. Poly (ether urethane)s containing various amounts of the chain extender with fluorinated side chains (FPUs) were prepared by isophorone diisocyanate (IPDI), polytetra‐methylene‐ether‐glycol (PTMG), 3‐aminopropyltriethoxysilane (KH‐550), and 1,4‐butandiol (BDO). Films of FPUs were investigated by water absorption, contact angle, pencil hardness, adhesive force, and thermal analysis. Coating FPUs on micro‐nano concave‐convex structure plate realizes superhydrophobic performance. Scanning electron microscope (SEM) and atomic force microscopy (AFM) demonstrated that there is a lot of irregular concave‐convex structure, which forms a typical air cushion model. X‐ray photoelectron spectroscopy (XPS) analysis showed that surface fluorine content is 165% more than that of film average fluorine content. The superhydrophobic plate with 10% or higher F‐containing FPUs coating is of outstanding chemical corrosion resistance, excellent solvent resistance, and wear resistance.  相似文献   
7.
In this paper, graphene oxide/polyethylene glycol (GO/PEG) composite water-based lubricant was prepared by an ultrasonic dispersion method, and characterized and analyzed by Fourier transform infrared (FT-IR), Raman spectroscopy, X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), and thermogravimetric analysis (TGA). The suspension performance of GO/PEG composite water-based lubricant in water was verified by static sedimentation and centrifugation, and then, the prepared GO/PEG composite water-based lubricant was added into 304 stainless steel and 6061 aluminum alloy, and the coefficient of friction (COF) curve, average COF value, average wear rate, corresponding photomicrographs of balls and disks after wear, and energy-dispersive spectrometer (EDS) elemental analysis were used to illustrate the lubrication effect and lubrication mechanism. The results show that the GO/PEG composite water-based lubricant possesses excellent suspension ability in water, and the average COF value and wear rate of GO/PEG composite water-based lubricant are reduced by 78.8% and 88.8%, respectively, compared with water lubrication. The excellent lubrication effect of GO/PEG composite water-based lubricant can effectively reduce the cold-welding and adhesive wear phenomenon, mainly because GO/PEG composite water-based lubricant first fills the uneven surface of friction mating to form a high-quality lubricating film and then because of the special space structure of GO and the low shear between GO layers and the synergistic lubrication effect of GO/PEG.  相似文献   
8.
混凝土运输过程中搅拌筒的磨损一直是一种常见潜在危害,磨损严重时会导致叶片失效,对搅拌的质量和出料匀质性产生影响。通过实验获取搅拌筒内部的磨损费时费力,因此有必要采取一种数值分析方法对搅拌筒的磨损进行预测并提出改进。本文采用摩擦磨损实验的方法来标定颗粒与搅拌筒之间的Archard磨损常数,采用JKR接触模型表征混凝土的流动性能,采用离散元方法(DEM)对搅拌筒筒体及叶片磨损进行预测分析。通过法向接触能量与切向接触能量的对比,证明搅拌筒中的磨损主要为伴有冲击作用的磨粒磨损,搅拌车搅拌筒中搅拌叶片顶部的磨损较为严重。针对磨损比较严重的叶片顶部进行改进,采用T型耐磨结构等改进叶片结构,叶片顶部结构改进后搅拌筒使用寿命能得到明显提升。  相似文献   
9.
为提高304不锈钢的摩擦学性能,将质量分数为30%和60%的球形WC添加到铁基复合粉末,采用等离子堆焊技术在其表面制备了WC增强铁基复合涂层.分析其显微组织结构、物相和显微硬度,在恒定载荷(50 N)和滑动速度(20 mm/s)下进行干摩擦磨损试验,研究其干滑动摩擦学性能.结果表明:富含Cr的固溶强化奥氏体、高硬度的Cr7C3和WC增强相的存在,提高了WC增强铁基堆焊层的硬度,30%WC和60%WC涂层的显微硬度达到HV0.2665和HV0.2724,比铁基涂层提高了21.1%和31.9%,是304基体的3.7和4倍;30%WC和60%WC涂层的摩擦系数和磨损率分别为0.59和2.639×10~(–6) mm~3·N~(–1)·m~(–1),0.42和1.111×10~(–6) mm~3·N~(–1)·m~(–1).30%WC和60%WC涂层均表现出优异的耐磨性能,其磨损机理分别为黏着磨损和二体磨粒磨损的混合机制,和三体磨粒磨损.  相似文献   
10.
室温条件下,采用CFT-Ⅰ型多功能材料表面综合性能测试仪对AISI 4340钢进行了往复干摩擦磨损试验,研究了其摩擦磨损特性.采用扫描电子显微镜(SEM)和能谱仪(EDS)对磨痕和亚表层进行了观察和检测,分析了磨损表面微观形貌、亚表层塑性变形和碳氧元素含量演化.结果表明:磨损形式以磨粒磨损为主,并伴随轻微黏着磨损和剥落磨损;磨损表面分布着长度、宽度、深度不一的划痕以及鳞片状和颗粒状磨屑;磨损表面出现轻微氧化,磨屑呈现不同程度的碳富集和氧化;亚表层出现明显摩擦影响层,距表层越近,塑性变形越明显,晶界角逐渐汇聚于表面,在表面处趋于平行;往复运动导致塑性变形方向不一致,磨痕中部,塑性变形向某位置聚集.  相似文献   
设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号