Nonlinear elastic constitutive relations of residually stressed composites with stiff curved fibres

Applied Mathematics and Mechanics - Mechanical models of residually stressed fibre-reinforced solids, which do not resist bending, have been developed in the literature. However, in some residually...     

Densitometry and indirect normal‐phase HPTLC–ESI–MS for separation and quantitation of drugs and their glucuronide metabolites from plasma

The present work describes novel methods using densitometry and indirect or off‐line high performance thin‐layer chromatography–mass spectrometry (HPTLC–MS) for the simultaneous detection and quantification of asenapine, propranolol and telmisartan and their phase II glucuronide metabolites. After chromatographic separation of the drugs and their metabolites the analytes were scraped, extracted in methanol and concentrated prior to mass spectrometric analysis. Different combinations of toluene and methanol–ethanol–n‐butanol–iso‐propanol were tested for analyte separation and the best results were obtained using toluene–methanol–ammonia (6.9:3.0:0.1, v/v/v) as the elution solvent. All of the drug–metabolite pairs were separated with a homologous retardation factor difference of ≥22. The conventional densitometric approach was also studied and the method performances were compared. Both of the approaches were validated following the International Conference on Harmonization guidelines, and applied to spiked human plasma samples. The major advantage of the TLC–MS approach is that it can provide much lower limits of detection (1.98–5.83 pg/band) and limit of quantitation (5.97–17.63 pg/band) with good precision (?3.0% coefficient of variation) compared with TLC–densitometry. The proposed indirect HPTLC–MS method is simple yet effective and has tremendous potential in the separation and quantitation of drugs and their metabolites from biological samples, especially for clinical studies.     

HgCdTe薄膜的输运特性及其应力调控

窄禁带直接带隙半导体材料碲镉汞(Hg1–xCdxTe)是一种在红外探测与自旋轨道耦合效应基础研究方面都具有重要应用意义的材料.本文对单晶生长的体材料Hg0.851Cd0.149Te进行阳极氧化以形成表面反型层,将样品粘贴在压电陶瓷上减薄后进行磁输运测试,在压电陶瓷未加电压时观察到了明显的SdH振荡效应.对填充因子与磁场倒数进行线性拟合,获得样品反型层二维电子气的载流子浓度为ns=1.25×10^16m^-2.在不同磁场下,利用压电陶瓷对样品进行应力调控,观测到具有不同特征的现象,分析应是样品中存在二维电子气与体材料两个导电通道.零磁场下体材料主导的电阻的变化应来源于应力导致的带隙的改变;而高场下产生类振荡现象的原因应为应力导致的二维电子气能级的分裂.     

水硬性石灰合成及拉破坏特性试验研究

水硬性石灰在欧洲石质文物修复和加固中获得了很大成功。我国的石质文物主要是砂岩,水硬性石灰的修复效果不好。为满足我国石质文物修复和加固的需求,本文以石灰石和黏土为原料,在950℃煅烧不同时间,制备出水硬性石,对试样的成分、微观形貌、收缩率、抗拉强度和拉破坏过程等进行了研究。结果表明:(1)试样中含有水硬性成分2CaO·SiO2(C2S);煅烧8h时,成分与欧洲水硬性石灰NHL5接近;1.5CaO·SiO2·xH2O(C-S-H)和CaCO3的含量随龄期的增加逐渐增加。(2)龄期1~3d,收缩率较小;龄期4~6d,收缩率以线性规律增加;7d以后,收缩率趋于稳定。(3)局部变形区随拉应力的增加而变大,邻近局部变形区逐渐合并,形成面积更大的应变局部化带;载荷超过峰值后,产生微裂隙;随载荷进一步增加,微裂隙扩展,贯穿整个试件,发展成宏观裂隙,使试件破坏。(4)抗拉强度随龄期的增加而增加,水硬性石灰中C-S-H、CaCO3等相互交织,构成空间致密体,使试件力学强度提高。合成的水硬性石灰物理力学性能与欧洲水硬性石灰NHL5相近,并且成分均匀、可控,在石质文物修复和加固工程中具有良好应用前景。     

Wall shear stress modified by bubbles in a horizontal channel flow of silicone oil in the transition region

We performed laboratory experiments on bubbly channel flows using silicone oil, which has a low surface tension and clean interface to bubbles, as a test fluid to evaluate the wall shear stress modification for different regimes of bubble migration status. The channel Reynolds numbers of the flow ranged from 1000 to 5000, covering laminar, transition and turbulent flow regimes. The bubble deformation and swarms were classified as packing, film, foam, dispersed, and stretched states based on visualization of bubbles as a bulk void fraction changed. In the dispersed and film states, the wall shear stress reduced by 9% from that in the single-phase condition; by contrast, the wall shear stress increased in the stretched, packing, and foam states. We carried out statistical analysis of the time-series of the wall shear stress in the transition and turbulent-flow regimes. Variations of the PDF of the shear stress and the higher order moments in the statistic indicated that the injection of bubbles generated pseudo-turbulence in the transition regime and suppressed drag-inducing events in the turbulent regime. Bubble images and measurements of shear stress revealed a correlated wave with a time lag, for which we discuss associated to the bubble dynamics and effective viscosity of the bubble mixture in wall proximity.     

Residual stress in polyethylene pipes

This paper deals with residual stress in polyethylene (PE) pipes as an important factor that influences their lifetime. Residual hoop stress distribution in a PE pipe was determined using a methodology previously carried out by the authors on polypropylene pipes. Axial residual stress magnitude was determined by comparison of experimental data and finite element modelling. Based on the obtained results, a new simplified methodology for determining the residual hoop stress is proposed. The method needs only one circular specimen made of pipe, but, unlike older methods, provides a more precise estimation of residual hoop stress distribution taking into account its exponential shape. Some older results from literature are recalculated using this method and residual hoop stress of various PE pipe grades and dimensions are then compared. To provide an idea of residual hoop stress influence on lifetime of a pipe, a lifetime estimation is carried out for the examined pipe.     

Cold,warm, and hot programming of shape memory polymers

In this article, programming is classified as hot, warm, and cold, based on the temperature zone within which the programming is conducted. The strain and stress locking and releasing mechanisms are discussed within the thermodynamics framework. A new formula is developed for quantifying the strain recovery ratio of cold-programmed SMPs. Stress fixity ratio and stress recovery ratio are also defined based on the understanding of stress locking and recovery mechanisms. State-of-the-art literature on warm and cold programming is reviewed. Well-controlled programming as well as free strain recovery test and constrained stress recovery test are conducted, in order to validate the memory mechanisms discussed in this study. It is found that, while programming temperature has an insignificant effect on the final free shape recovery, it has a significant effect on the stress recovery. The recovery stress programmed by cold programming may be lower, equal to, or higher than that by hot programming, due to the different stress locking mechanisms and other factors such as damage during the thermomechanical cycle. Cold, Warm, and Hot Programming of Shape Memory Polymers © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1319–1339     

Stress memory polymers

Like shape memory polymers, a novel phenomenon of stress memory was shown in which the stress of a material can respond to an external stimulus. This concept was further enlightened by a switch‐spring‐frame model that would eliminate the limitation of existing models which overlooked the stimulus responsive nature of such polymers. The discovery being reported in this article was stemmed from a real case study into shape memory polymer fibers in compression stocking for varicose veins. The breakthrough of stress memory enabled researchers to develop applications needing stimuli‐responsive forces, which can broaden the horizon of such smart polymers in emerging smart products in many multidisciplinary fields such as sensors, stress garments, and massage devices, electronic skins, and artificial muscles. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 893–898     

The ASBM-SA turbulence closure: Taking advantage of structure-based modeling in current engineering CFD codes

Structure-based turbulence models (SBM) carry information about the turbulence structure that is needed for the prediction of complex non-equilibrium flows. SBM have been successfully used to predict a number of canonical flows, yet their adoption rate in engineering practice has been relatively low, mainly because of their departure from standard closure formulations, which hinders easy implementation in existing codes. Here, we demonstrate the coupling between the Algebraic Structure-Based Model (ASBM) and the one-equation Spalart–Allmaras (SA) model, which provides an easy route to bringing structure information in engineering turbulence closures. As the ASBM requires correct predictions of two turbulence scales, which are not taken into account in the SA model, Bradshaw relations and numerical optimizations are used to provide the turbulent kinetic energy and dissipation rate. Attention is paid to the robustness and accuracy of the hybrid model, showing encouraging results for a number of simple test cases. An ASBM module in Fortran-90 is provided along with the present paper in order to facilitate the testing of the model by interested readers.     

航空导管弯曲试验的疲劳裂纹萌生寿命

飞行器液压导管受接头和卡箍等约束，在使用的振动环境中，会因弯曲应力而导致破裂，影响到飞行安全．本文对飞行器液压系统通用的不锈钢导管的裂纹萌生寿命进行了试验研究．首先在对8 mm、12 mm 无缺陷导管和含U 型缺口8 mm 导管的疲劳试验和有限元分析的基础上，得到了导管的最大拉应变-裂纹萌生寿命数据．然后采用基于强度极限和弹性模量估算法的Manson-Coffin 公式来预测导管裂纹萌生寿命．最后引入加载类型修正系数、表面质量修正系数、试样尺寸修正系数、应力集中敏感系数和有效应力集中系数，使修正后的公式对三种类型的导管均有较好的裂纹萌生寿命预测精度．