An Efficient Numerical Model for Planar Spiral Inductor On-Chip

In this paper, a very useful numerical technique has been developed for analyzing the transient characteristics of a planar-spiral inductor on-chip. A locally conformal technique and an alternating-direction implicit scheme are applied to the finite-difference time-domain method. A formulation for solving three dimensional Maxwell’s equations is proposed. Using the proposed method, various parameters of the planar-spiral inductors have been analyzed and an equivalent circuit, which includes frequency-independent circuit elements, has been introduced. Highly computational efficiency is implemented. Numerical results show excellent agreement with the measured data over a wide frequency range.     

Dynamic surface tension measurements of surfactant solutions using the maximum bubble pressure method – limits of applicability

One of the essential differences in the design of bubble pressure tensiometers consists in the geometry of the measuring capillaries. To reach extremely short adsorption times of milliseconds and below, the so-called deadtime of the capillaries must be of the order of some 10 ms. In particular, for concentrated surfactant solutions, such as micellar solutions, short deadtimes are needed to minimize the initial surfactant load of the generated bubbles. A theoretical model is derived and confirmed by experiments performed for a wide range of experimental conditions, mainly in respect to variations in deadtime and bubble volume.     

Study on the possibilities of controlling the laser output beam properties by an intracavity deformable mirror

The possibilities of controlling the laser beam properties by a deformable mirror introduced into the laser optical cavity were studied theoretically and experimentally. The experiments were performed under conditions of an industrial high power transverse flow cw CO₂ laser operating with a stable resonator of a folded configuration. A deformable bimorph mirror of a surface profile controlled by the voltage applied to the mirror electrodes is implemented to the laser system as a back cavity mirror or as a one of the inner folding mirrors. The near-and far-field characteristics of the laser beam versus the resonator configuration controlled by the changes of the focal length of the deformable mirror are discussed in the paper. The analysis reveals that the resonator with an inner deformable mirror is much more sensitive to the mirror curvature variations than the resonator in which the deformable mirror is used as a back cavity mirror. The presented results show that dynamic and controllable changes in the resonator properties result in the controlled modification and optimisation of the laser output power and spatial parameters of the laser radiation.     

Studies on calcium‐containing poly(urethane ether)s

The calcium salt of mono(hydroxyethoxyethyl)phthalate [Ca(HEEP)₂] was synthesized by the reaction of diethylene glycol, phthalic anhydride, and calcium acetate. Calcium‐containing poly(urethane ether)s (PUEs) were synthesized by the reaction of hexamethylene diisocyanate (HMDI) or tolylene 2,4‐diisocyanate (TDI) with a mixture of Ca(HEEP)₂ and poly(ethylene glycol) (PEG₃₀₀ or PEG₄₀₀) with di‐n‐butyltin dilaurate as a catalyst. A series of calcium‐containing PUEs of different compositions were synthesized with Ca(HEEP)₂/PEG₃₀₀ (or PEG₄₀₀)/diisocyanate (HMDI or TDI) molar ratios of 2:2:4, 3:1:4, and 1:3:4 so that the coating properties of the PUEs could be studied. Blank PUEs without calcium‐containing ionic diols were also prepared by the reaction of PEG₃₀₀ or PEG₄₀₀ with HMDI or TDI. The PUEs were well characterized by Fourier transform infrared, ¹H and ¹³C NMR, solid‐state cross‐polarity/magic‐angle‐spinning ¹³C NMR, viscosity, solubility, and X‐ray diffraction studies. The thermal properties of the polymers were also studied with thermogravimetric analysis and differential scanning calorimetry. The PUEs were applied as top coats on acrylic‐coated leather, and their physicomechanical properties were also studied. The coating properties of PUEs, such as the tensile strength, elongation at break, tear strength, water vapor permeability, flexing endurance, cold crack resistance, abrasion resistance, color fastness, and adhesive strength, were better than the standard values. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2865–2878, 2003     

Effects of Moisture and Stresses on the Structure and Properties of Polyester Resin

The results of a complex study of structural changes in a cured Norpol 440 polyester resin under the action of damp environment and mechanical loading are presented. A considerable effect of absorbed moisture on the structure and some characteristics of the material is revealed by using thermophysical methods and X-ray diffractometry. The joint effect of moisture and mechanical stress is estimated by investigating the creep in stationary and nonstationary moisture conditions. The anisotropy of the material structure formed during creep is evaluated from the results of dilatometric measurements. It is found that the degree of anisotropy of the material after creep accompanied by moisture sorption is higher than that after creep in the conditions of moisture equilibrium with atmosphere. It is established that the aftercure and relaxation of the residual creep deformation come to an end at heating to 80-85°C. At a further rise in temperature and repeated heating, changes in the material structure are not observed.     

Stratifiable Families of Extremals and Sufficient Conditions for Optimality in Optimal Control Problems

It is shown that, if a parametrized fämily of extremals F can be stratified in a way compatible with the flow map generated by F, then those trajectories of the family which realize the minimal values of the cost in F are indeed optimal in comparison with all trajectories which lie in the region R covered by the trajectories of F. It is not assumed that F is a field covering the state space injectively. As illustration, an optimal synthesis is constructed for a system where the flow of extremals exhibits a simple cusp singularity.     

应变Si1-xGex层中p型杂质电离常温和低温特性

本文采用解析的方法计算了应变Si1-xGex层中p型杂质电离度与Ge组分x、温度T以及掺杂浓度N的关系.发现常温时,在同一Ge组分下,随着掺杂浓度的升高,杂质的电离度的先变小,而后又迅速上升到1.在同一掺杂浓度下,轻掺杂时,杂质的电离度随Ge组分的增加先变大,而后几乎不变;重掺杂时,杂质电离能变为0后,杂质电离度为1.低温下,轻掺杂时,载流子低温冻析效应较为明显,杂质的电离度普遍较小,当掺杂浓度大于Mott转换点时,载流子冻析效应不再明显,电离率迅速上升到1.在同一Ge组分下,随着掺杂浓度的升高,杂质的电离度先变小,后变大,而后又迅速上升到1.在同一掺杂浓度下,轻掺杂时,杂质的电离度随Ge组分的增加变大;重掺杂时,杂质电离能变为0后,杂质电离度为1.     

Stability of solutions to the Cauchy problem for a plane hyperbolic system with time-periodic coefficients

Considering a plane hyperbolic system with time-periodic coefficients, we construct a version of the direct Lyapunov method with the condition on the derivative of the Lyapunov functional along the trajectories of the system which is weakened by use of periodicity of the coefficients. We exhibit an illustrative example.     

Evaluation of PLE exhaustiveness for the extraction of PCBs from sediments and the influence of sediment characteristics

Pressurized liquid extractions were performed on eight sediments in order to investigate if a modified US EPA method (100 °C, 100 bar, n-heptane/acetone (1:1), 2 × 5 min) provided exhaustive extractions of polychlorinated biphenyls (PCBs) from sediment, and to study if the extractability of PCBs from the different sediments was affected by characteristics of the sediment. The recovery from the eight native sediments, contaminated in nature, was between 96.4% and 98.9%, as an average of the recoveries from 10 PCB congeners. Hundred percent recovery was defined as the sum of two consecutive extractions (2 × 5 min each) at the stated conditions. The recoveries of the individual congeners were above 94%, except for one congener in one sediment, which had a recovery of 92%. When the recoveries and different characteristics of the sediments were compared, no correlation appeared between recoveries and sediment PCB concentration, total organic carbon (TOC), soot carbon (SC) or amorphous carbon (AC). The fact that carbon did not influence the extractions was somewhat surprising, since previous experiments have indicated a connection. Instead, statistically significant (p < 0.05) correlations were observed for water content and carbon/nitrogen (C/N) ratio. The decrease in recoveries with decreased water content was attributed to less access of the solvent to the analytes due to less matrix swelling. The lowered recoveries with increased C/N ratio can indicate that a difference in structure of the organic matter exists, which influences the binding strength between the analytes and the matrix. The difference in structure can possibly be explained by different origin of the organic matter or by aging effects. Overall the method was found to be exhaustive and the excellent recoveries show that sediment characteristics do not influence the extractions markedly.     

显像管调制特性的测量与分析

测试了显象管调制特性曲线，并分析了特性曲线与显像管工作原理．