旋涂法制备WO3薄膜电致变色性能

"智能窗"大规模推广顺应可持续发展潮流,三氧化钨(WO_3)是生产"智能窗"的一种重要电致变色材料,但调控WO_3薄膜电致变色性能机制仍待进一步研究。采用旋涂法制备WO_3薄膜,重点研究了溶液浓度和旋涂次数对调控WO_3薄膜电致变色性能的影响。通过表面轮廓仪测量薄膜厚度,X射线衍射(XRD)测量薄膜结晶情况,原子力显微镜(AFM)和扫描电子显微镜(SEM)分析薄膜表面形貌,光谱仪测量薄膜初始态、着色态和褪色态的透射率。实验结果表明,随着溶液浓度增加(0. 2～1. 0 mol/L),薄膜厚度从9. 7 nm增加到33. 3 nm,透射率调制能力从0%提升到37. 0%;多次旋涂薄膜厚度线性增长,线性拟合优度(R~2)达0. 98,5次旋涂后透射率调制能力达51. 3%。改变溶液浓度和旋涂次数都是调控薄膜透射率调制能力的有效手段,精准调控薄膜透射率调制能力对设计不同应用场景的电致变色器件具有重大意义。     

In原子在GaAs(001)表面的成核与扩散研究

近年来,半导体量子点特别是InAs量子点的基本物理性质和潜在应用得到了广泛研究。许多研究者利用InAs量子点结构的改变以调制其光电特性。本文采用液滴外延法在GaAs(001)表面沉积了不同沉积量的In(3 ML、4 ML、5 ML),以研究In的成核机制和表面扩散。实验发现,随着In沉积量的增加,液滴尺寸(包括直径、高度)明显增大。不仅如此,在相同的衬底温度下,沉积量越大,液滴密度越大。利用经典成核理论,计算了GaAs(001)表面In液滴形成的临界厚度为0.57 ML,计算的结果与已报道的实验一致。从In原子在表面的迁移和扩散,以及衬底中Ga和液滴中的In之间的原子互混原理解释了In液滴形成和形貌演化的机理。实验中得到的In液滴临界厚度以及In液滴在GaAs(001)上成核机理,可以为制备InAs量子点提供实验指导。     

工质对微通道沸腾液膜瞬态变化的影响

本文采用去离子水和无水乙醇两种工质,利用微通道流动沸腾同步测量实验系统,研究了液膜厚度的瞬态变化规律,实验发现流动沸腾形成的初始液膜厚度在毛细数Ca很宽的范围内都遵循Taylor流动原理;液膜形成后,在蒸发和蒸汽流动携带的耦合作用下,厚度迅速减薄直至蒸干;由于水的汽液黏度比小,速度梯度小,剪切作用带来的液膜厚度减少量小,且水的汽化潜热大,吸收相同热量时蒸发量小,导致水的液膜厚度变化斜率较小,通过理论分析提出了沸腾液膜厚度变化的计算模型,计算结果与实验结果的误差小于20%。     

虚拟震源测深法及其在INDEPTH-3台阵中的应用

基于中美合作项目INDEPTH第3期在青藏高原布设的台站，使用虚拟震源测深法研究青藏高原中部的地壳厚度。结果显示，拉萨地体和羌塘地体的地壳结构存在巨大差异。拉萨地体的地壳厚度大约为57 km，与艾里均衡说预测的地壳厚度基本一致，说明拉萨地体的地壳结构比较简单。羌塘地体的地壳厚度为60~75 km，向北有增厚趋势，明显较艾里均衡说预测的地壳厚，说明羌塘地体地壳结构比较复杂，原因有可能是羌塘地体下存在高温流体和低速带，或者与印度板块岩石圈在班公湖-怒江缝合带以北向下俯冲有关。     

染料敏化太阳能电池载流子传输的数值模拟

由于在染料敏化太阳能电池(dye-sensitized solar cell, DSSC)中存在染料弛豫、半导体薄膜中电子与氧化态染料分子发生反应和电子在电解质中与氧化态离子复合等不利反应,利用一个更完善的DSSC载流子传输模型对电池的光电性能进行模拟就显得非常重要。为此,本文基于由多重俘获理论建立的DSSC中的包括电子、染料阳离子、碘化物和三碘化物在内的载流子传输模型,数值模拟得到了不同TiO₂薄膜厚度、不同入射光强度与不同染料分子吸收系数下DSSC的J-V曲线。结果表明,随着TiO₂薄膜厚度的增加,太阳能电池的短路电流密度增大,开路电压减小,光电转换效率先增大后减小。当DSSC的TiO₂薄膜厚度为20 μm时,光电转换效率达到最大值7.41%,同时光电转换效率随入射光强度与染料分子吸收系数的增大均有一定程度提高,其中在吸收系数为4 500 cm^-1时,光电转换效率为6.73%。以上结果可以为改进DSSC的光电性能提供理论指导。     

Effect of thickness variations of lithium niobate on insulator waveguide on the frequency spectrum of spontaneous parametric down-conversion

We study the effect of waveguide thickness variations on the frequency spectrum of spontaneous parametric down-conversion in the periodically-poled lithium niobate on insulator (LNOI) waveguide. We analyze several variation models and our simulation results show that thickness variations in several nanometers can induce distinct effects on the central peak of the spectrum, such as narrowing, broadening, and splitting. We also prove that the effects of positive and negative variations can be canceled and thus lead to a variation-robust feature and an ultra-broad bandwidth. Our study may promote the development of on-chip photon sources in the LNOI platform, as well as opens up a way to engineer photon frequency state.     

Method of measuring one-dimensional photonic crystal period-structure-film thickness based on Bloch surface wave enhanced Goos-Hänchen shift

This paper puts forward a novel method of measuring the thin period-structure-film thickness based on the Bloch surface wave (BSW) enhanced Goos-Hänchen (GH) shift in one-dimensional photonic crystal (1DPC). The BSW phenomenon appearing in 1DPC enhances the GH shift generated in the attenuated total internal reflection structure. The GH shift is closely related to the thickness of the film which is composed of layer-structure of 1DPC. The GH shifts under multiple different incident light conditions will be obtained by varying the wavelength and angle of the measured light, and the thickness distribution of the entire structure of 1DPC is calculated by the particle swarm optimization (PSO) algorithm. The relationship between the structure of a 1DPC film composed of TiO₂ and SiO₂ layers and the GH shift, is investigated. Under the specific photonic crystal structure and incident conditions, a giant GH shift, 5.1×10³ times the wavelength of incidence, can be obtained theoretically. Simulation and calculation results show that the thickness of termination layer and periodic structure bilayer of 1DPC film with 0.1-nm resolution can be obtained by measuring the GH shifts. The exact structure of a 1DPC film is innovatively measured by the BSW-enhanced GH shift.     

Geometric Design of Anode-Supported Micro-Tubular Solid Oxide Fuel Cells by Multiphysics Simulations

High volumetric power density (VPD) is the basis for the commercial success of micro-tubular solid oxide fuel cells (mtSOFCs). To find maximal VPD (MVPD) for anode-supported mtSOFC (as-mtSOFC), the effects of geometric parameters on VPD are analyzed and the anode thickness, t_an, and the cathode length, l_ca, are identified as the key design parameters. Thermo-fluid electrochemical models were built to examine the dependence of the electrical output on the cell parameters. The multiphysics model is validated by reproducing the experimental I-V curves with no adjustable parameters. The optimal l_ca and the corresponding MVPDs are then determined by the multiphysics model for 20 combinations of r_in, the inner tube radius, and t_an. And all these optimization are made at 1073.15 K. The results show that:(i) significant performance improvement may be achieved by geometry optimization, (ii) the seemingly high MVPD of 11 and 14 W/cm³ can be easily realized for as-mtSOFC with single-and double-terminal anode current collection, respectively. Moreover, the variation of the area specific power density with l_ca2(2 mm, 40 mm) is determined for three representative (r_in, t_an) combinations. Besides, it is demonstrated that the current output of mtSOFC with proper geometric parameters is comparable to that of planar SOFC.     

经腹彩色多普勒超声检查对子宫内膜异位症的诊断价值

本研究选取我院100例子宫内膜异位症患者作为病例组、同期健康妇女100例作为对照组,探讨了经腹彩色多普勒超声检查对子宫内膜异位症患者子宫动脉血流特征、子宫特征的诊断价值。结果显示,病例组的子宫体积、子宫内膜厚度测定值均大于对照组(P<0.05);摆动子宫颈后,病例组的EDV测定值低于对照组,RI测定值大于对照组(P<0.05);通过绘制ROC曲线,可知EDV、RI、子宫体积大小、子宫内膜厚度诊断子宫内膜异位症的AUC值均超过0.65,灵敏度和特异度都较高,漏诊率和误诊率也在可控范围内。本研究证实,通过经腹彩色多普勒超声检测子宫动脉血流参数及子宫形态特征,对诊断子宫内膜异位症具有一定的临床参考价值。     

Synergic Enhancement of High-density Polyethylene through Ultrahigh Molecular Weight Polyethylene and Multi-flow Vibration Injection Molding: A Facile Fabrication with Potential Industrial Prospects

General-purpose plastics with high strength and toughness have been in great demand for structural engineering applications. To achieve the reinforcement and broaden the application scope of high-density polyethylene(HDPE), multi-flow vibration injection molding(MFVIM) and ultrahigh molecular weight polyethylene(UHMWPE) are synergistically employed in this work. Herein, the MFVIM has better shear layer control ability and higher fabrication advantage for complex parts than other analogous novel injection molding technologies reported.The reinforcing effect of various filling times and UHMWPE contents as well as the corresponding microstructure evolution are investigated.When 5 wt% UHMWPE is added, MFVIM process with six flow times thickens the shear layer to the whole thickness. The tensile strength and modulus increase to 2.14 and 1.39 times, respectively, compared to neat HDPE on the premise of remaining 70% impact strength. Structural characterizations indicate that the enhancement is attributed to the improvement of shish-kebab content and lamellae compactness, as well as related to the corresponding size distributions of undissolved UHMWPE particles. This novel injection molding technology with great industrial prospects provides a facile and effective strategy to broaden the engineering applications of HDPE materials. Besides, excessive UHMWPE may impair the synergistic enhancement effect, which is also reasonably explained.