发动机机油滤清器虑层强度分析及优化

针对机油滤清器工作工况下进出口压差、机油滤层强度及导流桩高度等问题, 通过试验测试与仿真相结合, 对滤清器初步设计进行了评估及优化, 以确保滤清器在工作工况下进出口压降及滤层强度能满足要求. 首先进行滤层性能试验, 得到滤层的惯性阻力系数和黏性阻力系数; 再通过滤层多孔介质CFD分析, 对滤清器进出口压降进行分析计算. 结果表明: 在-18℃、25℃和70℃的工况下, 进出口压降都小于10kPa, 满足相关要求. 针对滤层的最大主应力超过其抗拉强度的问题, 通过CAE仿真分析, 优化滤层与导流桩间隙, 将滤层最大主应力由110.1MPa降至36.99MPa, 小于其抗拉强度42.8MPa.     

Controlling thermomechanical behavior of semicrystalline hydrogenated polynorbornene through the cis- to trans-cyclopentylene ratio

Though polynorbornene synthesized by ring-opening metathesis polymerization has an intrinsically all-cis configuration of the cyclopentylene backbone rings, a fraction of these rings can be epimerized to the trans configuration during hydrogenation over suitable catalysts. By varying the method of hydrogenation, semicrystalline hydrogenated polynorbornenes (hPNs) with trans levels between 0 and 36% were obtained. With increasing trans content, the glass transition temperature, melting point, and enthalpy of melting decrease modestly. By contrast, the temperature at which the hPN crystal transitions into a rotationally disordered polymorph varies strongly with trans content, ranging from 126 °C (all-cis) to 71 °C at 27% trans; at trans contents of 34% and above, no rotationally-ordered phase is observed at any temperature. The room-temperature Young's modulus shows no dependence on trans content, while the yield stress drops by 20% at 1% trans content and slowly decreases further with additional epimerization. The temperature dependence of the Young's modulus differs for trans-containing versus all-cis polymers, while the temperature dependence of the yield stress is set by the polymorph type (rotationally ordered vs. disordered).     

Nonlinear elastic constitutive relations of residually stressed composites with stiff curved fibres

Applied Mathematics and Mechanics - Mechanical models of residually stressed fibre-reinforced solids, which do not resist bending, have been developed in the literature. However, in some residually...     

水流损失和热补偿共同作用对增强型地热系统(EGS)产能影响的研究

基于青海共和盆地-3705m地热田实测数据,结合流固耦合传热理论并运用Comsol软件,建立了离散型裂隙岩体流体传热模型。考虑水流损失和热补偿共同作用,模拟得到了开采过程中上、下岩层(盖层和垫层)为绝热不渗透、传热不渗透、渗透传热时,储层(上、下岩层和压裂层)温度场的变化特征,分析了产出流量、水流损失、产出温度、产热速率的变化规律。研究结果表明:采热过程中产出流量始终小于注入流量;产出流量增幅速率先增大后减小,最后趋于稳定,前3a产出流量增幅超过总增幅量的3/4;忽略水流损失,将高估产热速率,采热初期甚至达到考虑水流损失时产热速率的3倍以上;考虑水流损失,产热速率呈先快速上升再趋于稳定后逐渐下降的趋势,最优开采时间为3a^11a;研究上、下岩层对产出温度的影响,仅考虑传热,采热寿命延长5.43%,同时考虑渗流传热时,采热寿命延长2.71%;采热前9a,水流损失占主导作用,即流入上、下岩层水流损失对产热速率的影响高于热补偿效应,开采10a后,热补偿效应占主导作用;同时考虑水流损失和热补偿效应得到的产热速率变化规律与实际工程更为符合,建议选择低渗透能力的上、下岩层延长增强型地热系统(EGS)运行时间。     

Enhancing hydrogen evolution of MoS2 basal planes by combining single-boron catalyst and compressive strain

MoS₂ is a promising candidate for hydrogen evolution reaction (HER), while its active sites are mainly distributed on the edge sites rather than the basal plane sites. Herein, a strategy to overcome the inertness of the MoS₂ basal surface and achieve high HER activity by combining single-boron catalyst and compressive strain was reported through density functional theory (DFT) computations. The ab initio molecular dynamics (AIMD) simulation on B@MoS₂ suggests high thermodynamic and kinetic stability. We found that the rather strong adsorption of hydrogen by B@MoS₂ can be alleviated by stress engineering. The optimal stress of −7% can achieve a nearly zero value of ΔG_H (~ −0.084 eV), which is close to that of the ideal Pt–SACs for HER. The novel HER activity is attributed to (i) the B– doping brings the active site to the basal plane of MoS₂ and reduces the band-gap, thereby increasing the conductivity; (ii) the compressive stress regulates the number of charge transfer between (H)–(B)–(MoS₂), weakening the adsorption energy of hydrogen on B@MoS₂. Moreover, we constructed a SiN/B@MoS₂ heterojunction, which introduces an 8.6% compressive stress for B@MoS₂ and yields an ideal ΔGH. This work provides an effective means to achieve high intrinsic HER activity for MoS₂.     

HgCdTe薄膜的输运特性及其应力调控

窄禁带直接带隙半导体材料碲镉汞(Hg1–xCdxTe)是一种在红外探测与自旋轨道耦合效应基础研究方面都具有重要应用意义的材料.本文对单晶生长的体材料Hg0.851Cd0.149Te进行阳极氧化以形成表面反型层,将样品粘贴在压电陶瓷上减薄后进行磁输运测试,在压电陶瓷未加电压时观察到了明显的SdH振荡效应.对填充因子与磁场倒数进行线性拟合,获得样品反型层二维电子气的载流子浓度为ns=1.25×10^16m^-2.在不同磁场下,利用压电陶瓷对样品进行应力调控,观测到具有不同特征的现象,分析应是样品中存在二维电子气与体材料两个导电通道.零磁场下体材料主导的电阻的变化应来源于应力导致的带隙的改变;而高场下产生类振荡现象的原因应为应力导致的二维电子气能级的分裂.     

离子浓度及表面结构对岩石孔隙内水流动特性的影响

酸性环境引发的岩石孔隙表面溶解增加了孔隙内水溶液的盐离子浓度,破坏了孔隙的表面结构.本文采用分子动力学模拟的方法研究了纳米级岩石孔隙内水溶液的流动特性,分析了盐离子浓度和孔隙表面结构对水流速度分布的影响及原因.研究结果表明:纳米级岩石孔隙内的水溶液流动符合泊肃叶流动特性,流速呈"抛物线"分布;随盐离子浓度增加,水溶液内部氢键网络变得更为致密,水黏度随其呈线性增长;水溶液中离子浓度越大,孔隙表面对水流动的阻力越大,最大流速越小,速度分布的"抛物线"曲率半径越大;岩石孔隙表面结构的破坏改变了流动表面的粗糙程度,增加了孔隙表面对H2O分子的吸引力.随表面结构破坏程度的增大,水溶液在近壁区域的密度增大,流速降低;当表面破坏程度达到50%时,水溶液在近壁区域出现了明显的负边界滑移现象.     

Information Network Modeling for U.S. Banking Systemic Risk

In this work we investigate whether information theory measures like mutual information and transfer entropy, extracted from a bank network, Granger cause financial stress indexes like LIBOR-OIS (London Interbank Offered Rate-Overnight Index Swap) spread, STLFSI (St. Louis Fed Financial Stress Index) and USD/CHF (USA Dollar/Swiss Franc) exchange rate. The information theory measures are extracted from a Gaussian Graphical Model constructed from daily stock time series of the top 74 listed US banks. The graphical model is calculated with a recently developed algorithm (LoGo) which provides very fast inference model that allows us to update the graphical model each market day. We therefore can generate daily time series of mutual information and transfer entropy for each bank of the network. The Granger causality between the bank related measures and the financial stress indexes is investigated with both standard Granger-causality and Partial Granger-causality conditioned on control measures representative of the general economy conditions.     

基于相场描述的拉压不对称强度结构拓扑优化

运用了基于相场描述的拓扑优化方法，来寻找在拉伸和压缩中表现出不对称强度行为的连续体结构的最优布局。依据Drucker-Prager屈服准则和幂率插值方案，优化问题可以描述为在局部应力约束下的最小化结构的体积。用qp放松法来解决应力约束的奇异性，并采用基于P-norm函数的聚合方法对应力约束进行凝聚，该方法实现了约束个数的降低，同时引入了稳定转化法来处理大量的局部应力约束和高度非线性的应力行为，以修正应力，提高优化收敛的稳定性。在优化问题求解时，使用拉格朗日乘子法对目标函数和应力约束进行处理。利用伴随变量法进行灵敏度分析，并通过求解Allen-Cahn方程更新相场函数设计变量。数值算例证明了该优化模型和相应数值技术的有效性，相关算例还揭示了考虑拉压不同强度和考虑同拉压强度约束时得到的结构优化拓扑构型具有显著的差异。     

Wall shear stress modified by bubbles in a horizontal channel flow of silicone oil in the transition region

We performed laboratory experiments on bubbly channel flows using silicone oil, which has a low surface tension and clean interface to bubbles, as a test fluid to evaluate the wall shear stress modification for different regimes of bubble migration status. The channel Reynolds numbers of the flow ranged from 1000 to 5000, covering laminar, transition and turbulent flow regimes. The bubble deformation and swarms were classified as packing, film, foam, dispersed, and stretched states based on visualization of bubbles as a bulk void fraction changed. In the dispersed and film states, the wall shear stress reduced by 9% from that in the single-phase condition; by contrast, the wall shear stress increased in the stretched, packing, and foam states. We carried out statistical analysis of the time-series of the wall shear stress in the transition and turbulent-flow regimes. Variations of the PDF of the shear stress and the higher order moments in the statistic indicated that the injection of bubbles generated pseudo-turbulence in the transition regime and suppressed drag-inducing events in the turbulent regime. Bubble images and measurements of shear stress revealed a correlated wave with a time lag, for which we discuss associated to the bubble dynamics and effective viscosity of the bubble mixture in wall proximity.