水硬性石灰合成及拉破坏特性试验研究

水硬性石灰在欧洲石质文物修复和加固中获得了很大成功。我国的石质文物主要是砂岩,水硬性石灰的修复效果不好。为满足我国石质文物修复和加固的需求,本文以石灰石和黏土为原料,在950℃煅烧不同时间,制备出水硬性石,对试样的成分、微观形貌、收缩率、抗拉强度和拉破坏过程等进行了研究。结果表明:(1)试样中含有水硬性成分2CaO·SiO2(C2S);煅烧8h时,成分与欧洲水硬性石灰NHL5接近;1.5CaO·SiO2·xH2O(C-S-H)和CaCO3的含量随龄期的增加逐渐增加。(2)龄期1~3d,收缩率较小;龄期4~6d,收缩率以线性规律增加;7d以后,收缩率趋于稳定。(3)局部变形区随拉应力的增加而变大,邻近局部变形区逐渐合并,形成面积更大的应变局部化带;载荷超过峰值后,产生微裂隙;随载荷进一步增加,微裂隙扩展,贯穿整个试件,发展成宏观裂隙,使试件破坏。(4)抗拉强度随龄期的增加而增加,水硬性石灰中C-S-H、CaCO3等相互交织,构成空间致密体,使试件力学强度提高。合成的水硬性石灰物理力学性能与欧洲水硬性石灰NHL5相近,并且成分均匀、可控,在石质文物修复和加固工程中具有良好应用前景。     

纳米银改性树脂基托机械性能的初步研究

采用磁控溅射技术在聚甲基丙烯酸甲酯(PMMA)树脂基托表面沉积一层纳米银(Ag NPs)涂层.研究了纳米银改性PMMA树脂基托的机械性能,为改性材料的临床应用提供理论基础.根据国际标准ISO2409:2007描述的划格法对涂层与基底的附着力强度进行测试,各组试件的接触角采用静态液滴法测量,三点弯曲法检测试件的弯曲强度.结果显示,各组涂层与PMMA基底材料结合良好,各组试件的表面润湿性变化不大,其中PMMA-Ag NPs80s组疏水性略有提高,各组试件的弯曲强度均符合国家标准.     

pH/temperature double responsive behaviors and mechanical strength of laponite‐crosslinked poly(DEA‐co‐DMAEMA) nanocomposite hydrogels

A nanocomposite (NC) hydrogel crosslinked by inorganic Laponite XLG was successfully synthesized via in situ free radical polymerization of monomers N,N‐diethylacrylamide and (2‐dimethylamino) ethyl methacrylate (DMAEMA). Polymerization was carried out at room temperature due to the accelerating effect of DMAEMA. The as‐prepared hydrogels displayed controlled transformation in optical transmittance and volume in response to small diversification of environmental factors, such as temperature and pH. The compressive strength of swollen D_6:1G₆ hydrogels was as high as 2219 kPa while compressive strain was 95%. Cyclic compression measurement exhibited good elastic properties of NC hydrogels. This work provides a facile method for fabricating stimuli‐responsive hydrogels with superior mechanical property. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 876–884     

基于SVM的固化土无侧限抗压强度模型

为实现较少试验次数下固化土无侧限抗压强度(qu)的准确预测, 提出了基于支持向量机(SVM)的固化土qu的预测模型. 以固化剂各组分掺入比、龄期、初始含水量、固化剂掺量等因素为输入量, 固化土的qu作为输出量, 以径向基为核函数, 采用网格搜索法和交叉验证法进行参数优化, 建立了基于SVM的固化土qu的预测模型. 算例分析表明: 该模型适用于任意条件下固化土qu的精确预测, 且在较小试验成本下实现与响应面法相当的预测精度.     

First-principles investigation on ideal strength of B2 NiAl and NiTi alloys

For B2 NiAl and NiTi intermetallic compounds, the ideal stress–strain image is lack from the perspective of elastic constants. We use first-principles calculation to investigate the ideal strength and elastic behavior under the tensile and shear loads. The relation between the ideal strength and elastic constants is found. The uniaxial tension of NiAl and NiTi along <001> crystal direction leads to the change from tetragonal path to orthogonal path, which is driven by the vanishing of the shear constant C(66). The shear failure under {110}{111} shear deformation occurring in process of tension may result in a small ideal tensile strength(~ 2 GPa) for NiTi. The unlikeness in the ideal strength of Ni Al and Ni Ti alloys is discussed based on the charge density difference.     

Determination of tensile strength of UHMWPE fiber-reinforced polymer composites

Quasi-static tensile test of UHMWPE fiber-reinforced composite laminate is challenging to perform due to low interlaminar shear strength and low coefficient of friction. Tensile tests proposed in the literature were conducted and limitations associated with each method led to the evolution of a new method. Tensile test of single-ply was realized as the best representative of tensile strength of a composite than tensile test of UHMWPE laminate. A fixture was developed for single-ply tests which increased friction and provided the mechanical constraint to slipping. The fixture is easy to fabricate and has provided repeatable results for eight grades of UHMWPE fiber-based (0/90) fabrics. Reported tensile strengths are in quite high range of 900–1500 MPa.     

Ocimum basilicum seed mucilage reinforced with montmorillonite for preparation of bionanocomposite film for food packaging applications

Use of nanocomposites is a well-established approach in enhancing the mechanical and barrier properties of bionanocomposite film for food packaging applications. The seed mucilage of Ocimum basilicum was employed for the preparation of bionanocomposite films with montmorillonite (MMT) as nanofiller. The films were prepared by solvent-casting method at varied solution pH (1, 3, 5 and 9) and MMT loading (1%, 3%, 5%, 10%, 15% and 20%). The films were characterized for physical, mechanical and barrier properties in addition to microstructure and X-ray diffraction pattern. XRD analysis revealed the exfoliated dispersion of MMT at pH 9, confirming its effective interaction with the bionanocomposite film. Maximum film tensile strength was achieved at a lower MMT load of 5%. Water vapour permeability reduced with increase in MMT loading up to 5%, followed by an increase at higher MMT loadings. Film formed at pH 9 showed tensile strength of 17.3 ± 0.33 MPa and reduced water vapour permeability (WVP) of 0.21 g mm.m⁻².hr⁻¹.kPa⁻¹.     

Highly stretchable,self-adhesive,and self-healable double network hydrogel based on alginate/polyacrylamide with tunable mechanical properties

A number of synthetic hydrogels suffer from low mechanical strength. Despite of the recent advances in the fabrication of tough hydrogels, it is still a great challenge to simultaneously construct high stretchability, and self-adhesive and self-healing capability in a hydrogel. Herein, a new type of double network hydrogel was prepared based on irreversible cross-linking of polyacrylamide chains and Schiff-base reversible cross-linking between glycidyl methacrylate-grafted ethylenediamine and oxidized sodium alginate (OSA). The combination of both cross-linkings and their synergistic effect provided a novel hydrogel with high strength, stretchable, rapid self-healing, and self-adhesiveness to different material. Besides, the hydrogels with diverse OSA content could maintain their original shapes after loading–unloading tensile test. The resulting hydrogel has a great potential in various fields for supporting and load-bearing substance.     

应力为SGBVE分布强度为指数分布下结构可靠度的估计

考虑了应力服从SGBVE分布,强度服从指数分布的应力—强度模型,分别在应力参数未知和部分强度参数未知的情形下给出了该模型可靠度的估计,并讨论了其性质.     

嵌段共聚物相容剂对聚合物共混体系力学性能影响的连续介观模拟

结合介观动力学方法和三维弹簧格子模型, 研究了嵌段共聚物相容剂对相容性较差的聚合物二元共混体系力学性能的影响. 在适当范围内不断增加嵌段共聚物相容剂的用量, 研究了相容剂含量对体系杨氏模数及拉伸强度的影响, 同时也对不同体系材料的破碎位点进行了分析. 结果表明, 未加入相容剂的二元共混体系在拉伸模拟中表现出较低的拉伸强度, 而适量添加相容剂可以显著提升材料的拉伸强度, 随着相容剂含量的增加, 共混体系的破碎位点会发生转移并最终改善材料的整体性能. 而相容剂的加入对体系杨氏模数的影响较小. 该连续模拟方法为关联聚合物复合体系的微观结构和宏观力学性能提供了一条高效的途径.