Condensed Mode Cooling of Ethylene Polymerization in Fluidized Bed Reactors

This review gives an overview of the evolution of the technology of condensed mode cooling, primarily for the case of ethylene polymerization on supported catalysts in fluidized bed reactors. It is well known that this mode of heat removal is quite effective in allowing polyolefin manufacturers to increase significantly production rates. What is perhaps less well understood are all of the issues that, in addition to the effect of the latent heat of vaporization of injected liquid components, also have an impact on the rate of production and behavior of the reactor. However, the liquid components injected into the reactor can vaporize rapidly under full‐scale conditions, leaving behind several heavy components (with respect to ethylene) that have numerous effects on how the particles behave, on the reaction rate, and on fluidization, fouling, and other parameters related to reactor and process performance.     

Study of the performances of an oxygen carrier: Experimental investigation of the binder's contribution and characterization of its structural modifications

The aim of this work is to investigate the contribution of the binder (NiAl₂O₄) on the performances of the oxygen carrier NiO/NiAl₂O₄. To this purpose, oxidation/reduction cycles have been performed in a fixed bed reactor using CO as a fuel. The results reveal that the binder can react with the fuel to form CO₂, and that its total reduction capacity increases with temperature. XRD characterizations performed on the binder (on the fresh and after several cycles) show a shift of the diffraction peaks of NiAl₂O₄ toward the ones of γ-alumina, which can be attributed to a progressive decomposition of NiAl₂O₄ to alumina and NiO.     

循环流化床粉煤灰可控制备高纯F型八面沸石研究

利用粉煤灰制备沸石分子筛是其高值化利用的重要方向之一.以循环流化床粉煤灰为原料,采用酸浸预处理-氢氧化钠碱熔活化-水热晶化法制备F型八面沸石,并用于吸附亚甲基蓝.考察酸浸温度、碱熔温度及碱灰质量比对粉煤灰结构的影响及碱熔温度、碱灰质量比、液固比及晶化时间对沸石的结构和形貌的影响.通过XRD和SEM对粉煤灰沸石的晶体结构和形貌进行表征.结果表明,利用循环流化床粉煤灰制备高纯F型八面沸石适宜条件为碱熔温度550℃,碱灰质量比1.5:1,液固比12 mL/g,晶体导向剂用量10;,晶化温度100℃,晶化时间20 h.其比表面积高达357 m2/g,且对亚甲基蓝的饱和吸附量高达178 mg/g.     

300 MW等级燃煤机组煤粉炉与循环流化床锅炉汞排放特性比较

选取某地330 MW煤粉炉(PC炉)和350 MW循环流化床锅炉(CFB)的燃煤电厂进行汞排放特性的研究。采用30B法和安大略法对两个燃煤电厂的除尘器入口、除尘器出口、脱硫塔出口和湿式电除尘器出口的烟气进行了取样和汞浓度分析,采集了入炉煤和副产物底渣、飞灰及脱硫石膏样品。通过样品中汞含量的分布,探讨了PC炉与CFB锅炉机组现有污染物控制设备对汞的协同脱除作用。结果表明,350 MW CFB电厂除尘器出口烟气平均汞浓度降低至0.43μg/m~3,布袋除尘器对汞的捕获效率达到98.9%,相应的燃烧副产物中飞灰是汞的主要富集对象。对于330 MW PC炉电厂,除尘器入口和除尘器出口烟气汞浓度均高于350 MW CFB电厂,烟气汞浓度从除尘器入口、除尘器出口到脱硫塔出口依次降低,在脱硫塔出口烟气汞浓度降低至0.42μg/m~3,静电除尘器和湿式脱硫塔对烟气汞的捕获效率分别为75.0%和22.4%,相应的产物中飞灰和脱硫石膏中汞都有一定程度的富集。     

Sorptive elimination of fluoride from contaminated groundwater in a fixed bed column: A kinetic model validation based study

The current investigation involves a continuous adsorption experiment in a packed bed column for the sorptive elucidation of fluoride from contaminated groundwater using an activated soil-clay mixture. Through the combination of naturally accessible laterite soil with silica enriched clay (3:1 ratio), a low-cost Al–Si heterogeneous material has been developed. Following detailed characterization, the developed materials were employed in a long-time column process to achieve a high degree of fluoride separation from real-world groundwater. In a packed bed column investigation, the effect of bed height, initial fluoride concentration, and flow rate on the breakthrough properties of the adsorption system were investigated. By using a non-linear regression equation, three model kinetics, such as the Thomas Model, Adams-Bohart Model, and Yoon-Nelson Model, were fitted to validate the column-based experimental data, by analysing the breakthrough curves profiles, and distinct kinetic parameters. The Bed Depth Service Time Analysis (BDST) model was tested to express the effect of bed height on breakthrough curves, as well as to predict the time for breakthrough, and material depletion under optimal conditions. The Thomas and Yoon-Nelson models were identified to be the most appropriate ones for describing the entire breakthrough curve, whereas the Adams-Bohart model was only utilised to predict the first half of the dynamic process. With correlation coefficients (R²) 0.96, the experimental results were well suited to Thomas, Yoon-Nelson, and Adams-Bohart models. Finally, regeneration assessment was carried out where even after four cycles of operation, regenerated adsorbent showed a rejection efficacy of 78% to fluoride that proves the viability of the material and methodology.     

Open-channel turbulent flow over non-uniform gravel beds

the measurements of flow over non-uniform gravel open channel have been conducted with Laser Doppler Velocimetry (LDV). The experimental results indicate that the distribution of mean velocity agrees well with the Nikuradse's law. From the distributions of resistance coefficient, reference level and turbulence intensity, the classification of small scale roughness case is obtained.Project supported by the National Science Foundation of China     

Modeling fluid and heat transport in the reactive, porous bed of downdraft (biomass) gasifier

A fluid flow and heat transfer model has been developed for the reactive, porous bed of the biomass gasifier to simulate pressure drop, temperature profile in the bed and flow rates. The conservation equations, momentum equation and energy equation are used to describe fluid and heat transport in porous gasifier bed. The model accounted for drag at wall, and the effect of radial as well as axial variation in bed porosity to predict pressure drop in bed. Heat transfer has been modeled using effective thermal conductivity approach. Model predictions are validated against the experiments, while effective thermal conductivity values are tested qualitatively using models available in literature. Parametric analysis has been carried out to investigate the effect of various parameters on bed temperature profile and pressure drop through the gasifier. The temperature profile is found to be very sensitive to gas flow rate, and heat generation in oxidation zone, while high bed temperature, gas flow rate and the reduction in feedstock particle size are found to cause a marked increase in pressure drop through the gasifier. The temperatures of the down stream zones are more sensitive to any change in heat generation in the bed as compared to upstream zone. Author recommends that the size of preheating zone may be extended up to pyrolysis zone in order to enhance preheating of input air, while thermal insulation should not be less than 15 cm.     

Investigation of operational parameters for an industrial CFB combustor of coal, biomass and sludge

The combustion of coal and/or biomass （sludge, wood waste, RDF, etc.） in a circulating fluidized bed has been a commercial topper for over 20 years, and references to principles and applications are numerous and widespread although few data are presented concerning the operation of large scale CFB-units. The authors studied the CFB-combustion at UPM-Kymmene （Ayr）, a major paper mill relying for its steam production upon the combustion of coal （80-85 %）, wood bark （5-10%） and wastewater treatment sludge （5-10%）. The maximum capacity of the CFB is 58 MWth. A complete diagnostic of the operation was made, and additional tests were performed to assess the operating mode. The plant schematics, relevant dimensions and process data are given. To assess the operation of the UPM-CFB, it is important to review essential design parameters and principles of CFB combustors, which will be discussed in detail to include required data, heat balance and flowrates, operating versus transport velocity, kinetics and conversion （including the possible effect of the Bouduard reaction if carbon is present）. Since the residence time in the riser and the cyclone efficiency determine the burnout of circulating fuel-particles, the UPM-CFB was subjected to a stimulus response technique using nickel oxide as tracer. Results illustrate the efficiency of the cyclone separation and the number of recycle loops for particles of a given size. Results will also be used to assess the cyclone operation and efficiency and to comment upon expected and measured carbon conversion.     

Waves in a Bed under Periodic Tangential Loading

The far-zone structure of the wave field in an elastic bed on a rigid foundation is considered. The wave field is generated by a tangential periodic force applied to the bed surface. The amplitude- frequency characteristics of surface vibrations for propagating modes are found. The partition of energy between different modes is considered.__________Translated from Prikladnaya Mekhanika i Tekhnicheskaya Fizika, Vol. 46, No. 4, pp. 109–115, July– August, 2005.