砂土串囊式充气锚杆承载力的研究

在砂土地层中,串囊式充气锚杆的研究还比较少,其承载特性及受力机理尚不明确。本文基于莫尔-库仑模型和Vesic圆孔扩张理论法,分别对圆柱体、球体、组合体、椭球体假设下的串囊式充气锚杆的扩大段进行计算分析。并将计算结果与试验得到的实测值进行对比。结果表明:四种形状假设中椭球体的形状假设理论值与实测值的误差最小,仅为8.35%。通过拟合试验数据,并引入与端阻力和侧摩阻力有关的两个系数对承载力公式进行修正,得到了抗拔承载力的经验公式。     

Polymer 4D printing: Advanced shape-change and beyond

4D printing is an exciting branch of additive manufacturing. It relies on established 3D printing techniques to fabricate objects in much the same way. However, structures which fall into the 4D printed category have the ability to change with time, hence the “extra dimension.” The common perception of 4D printed objects is that of macroscopic single-material structures limited to point-to-point shape change only, in response to either heat or water. However, in the area of polymer 4D printing, recent advancements challenge this understanding. A host of new polymeric materials have been designed which display a variety of wonderful effects brought about by unconventional stimuli, and advanced additive manufacturing techniques have been developed to accommodate them. As a result, the horizons of polymer 4D printing have been broadened beyond what was initially thought possible. In this review, we showcase the many studies which evolve the very definition of polymer 4D printing, and reveal emerging areas of research integral to its advancement.     

FeCoCrCuNi高熵合金裂纹及孔洞结构力学与微观构象演化机理的分子动力学模拟研究

本文采用分子动力学方法研究了FeCoCrCuNi高熵合金裂纹及孔洞模型结构在不同轴向拉伸应变速率下的力学与微观结构演化机理. 结果表明：应变速率越高FeCoCrCuNi裂纹结构对应更高的过冲应变和过冲应力，其主要原因是高拉伸速率会导致高强度的BCC结构及孪晶结构的生成，而BCC结构及孪晶结构的产生进而会抑制应力的下降，通过应力-应变曲线，可知FeCoCrCuNi裂纹模型在轴向应力作用下表现为塑性形变. 对于不同尺寸的孔洞FeCoCrCuNi裂纹模型的应力模拟与结构分析，可以得出：孔洞尺寸越大, FeCoCrCuNi裂纹结构对应的过冲应变和过冲应力越小，其主要原因是大尺寸的孔洞造成孔洞之间产生裂纹的，进而会影响这个材料的屈服应变和屈服强度.     

基于相移偏折法的高反射表面面形测量技术

利用单相机所采集的图像实现了对光滑高反射表面面形的直接检测.首先利用相机获取参考平面在标准平面镜中的镜像,然后通过参考平面上的点与归一化成像平面上图像点之间的密集折返对应关系,求得待测镜面的深度距离,从而实现对高反射表面面形的测量.通过光线追迹将该测量过程转化为求解物空间中关于两对应光线束之间的相交问题.以相位为载体获取面形梯度分布,求得该表面的法向量场,并求解相应的反射光线束.通过光线追迹对该光线束与相应入射光线束求“交点”检测高反射表面.对标准平面镜进行实验检测,测量得到的面形平面度为0.19 mm.采用传统方法与本文所提方法对汽车后视镜进行检测,所得检测结果对应点之间的平均距离为0.15 mm,验证了本文方法检测镜面面形的有效性.     

ICP-AES法测定高温合金中5种非金属元素

本文研究了快速测定高温合金中5种非金属元素(As、B、P、Se、Si)的分析方法,以满足高温合金行业对非金属元素检测的需求。利用王水和高氯酸对高温合金进行酸溶解,并系统研究了基体元素和共存元素对分析元素谱线的光谱干扰情况,同时进行了分析谱线的选择。5种非金属元素的检出限在5.5 ～ 11.9 ug/ml,5次数据的相对标准偏差(RSD,n=5)为0.9 % ～ 7 %,各元素的回收率在96 % ～ 102 %之间,该方法适用于高温合金中非金属元素的测定。     

Uniform stability of semilinear wave equations with arbitrary local memory effects versus frictional dampings

This paper is concerned with the mixed initial–boundary value problem for semilinear wave equations with complementary frictional dampings and memory effects. We successfully establish uniform exponential and polynomial decay rates for the solutions to this initial–boundary value problem under much weak conditions concerning memory effects. More specifically, we obtain the exponential and polynomial decay rates after removing the fundamental condition that the memory-effect region includes a part of the system boundary, while the condition is a necessity in the previous literature; moreover, for the polynomial decay rates we only assume minimal conditions on the memory kernel function g, without the usual assumption of $g^{\prime }$ controlled by g.     

Formation of low-temperature deformation-induced segregations of nickel in Fe–Ni-based austenitic alloys

ABSTRACT

The authors present the results of an investigation in Fe–Ni-Cr austenitic alloys of the low-temperature deformation-induced segregations of nickel that form in the micro regions being (i) located close to grain- and subgrain boundaries and (ii) characteristic of the concentration and magnetic inhomogeneities indicated by the appearance of a dark diffraction contrast at the electron diffraction patterns taken from these regions typical (at the same time) of an enhanced value of Curie temperature. The observed effects were connected with the micro distortions caused by the local change of lattice parameter because of an increase in nickel concentration, as well as in the result of a magnetostriction dilatation. Using methods of the X-ray energy dispersive spectroscopy (XEDS) and atomic-probe body-section radiography (tomography – APT) has made it possible to determine the borders of those regions of austenite that were characteristic of an enhanced concentration of nickel in the fields of the localisation of a deformation-induced segregation of nickel in the vicinity of grain (subgrain) boundaries of austenitic alloys of the types Fe–13Cr–30Ni and Fe–37Ni–3Ti.     

Connecting free volume with shape memory properties in noncytotoxic gamma‐irradiated polycyclooctene

The free volume holes of a shape memory polymer have been analyzed considering that the empty space between molecules is necessary for the molecular motion, and the shape memory response is based on polymer segments acting as molecular switches through variable flexibility with temperature or other stimuli. Therefore, thermomechanical analysis (TMA) and positron annihilation lifetime spectroscopy (PALS) have been applied to analyze shape recovery and free volume hole sizes in gamma‐irradiated polycyclooctene (PCO) samples, as a noncytotoxic alternative to more conventional PCO crosslinked via peroxide for future applications in medicine. Thus, a first approach relating structure, free volume holes and shape memory properties in gamma‐irradiated PCO is presented. The results suggest that free volume holes caused by gamma irradiation in PCO samples facilitate the recovery process by improving movement of polymer chains and open possibilities for the design and control of the macroscopic response. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1080–1088     

3D‐morphology reconstruction of nanoscale phase‐separation in polymer memory blends

In many organic electronic devices functionality is achieved by blending two or more materials, typically polymers or molecules, with distinctly different optical or electrical properties in a single film. The local scale morphology of such blends is vital for the device performance. Here, a simple approach to study the full 3D morphology of phase‐separated blends, taking advantage of the possibility to selectively dissolve the different components is introduced. This method is applied in combination with AFM to investigate a blend of a semiconducting and ferroelectric polymer typically used as active layer in organic ferroelectric resistive switches. It is found that the blend consists of a ferroelectric matrix with three types of embedded semiconductor domains and a thin wetting layer at the bottom electrode. Statistical analysis of the obtained images excludes the presence of a fourth type of domains. The criteria for the applicability of the presented technique are discussed. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 1231–1237